Table of Contents
Advertisement
Quick Links
Centrum SV... DV... TV...
EN
Installation and operating instructions
29993227
29993228
29993229
29993230
29993231
29993232
29993233
29993234
29993235
29993236
29993237
29993238
29993239
29993240
29993241
29993242
29993243
29993244
CD_TE062 rev00
Centrum SV406
Centrum SV408
Centrum SV605
Centrum SV608
Centrum SV1004
Centrum SV1006
Centrum DV406
Centrum DV408
Centrum DV605
Centrum DV608
Centrum DV1004
Centrum DV1006
Centrum TV406
Centrum TV408
Centrum TV605
Centrum TV608
Centrum TV1004
Centrum TV1006
Advertisement
Table of Contents
Related Manuals for Wilo Centrum SV Series
Summary of Contents for Wilo Centrum SV Series
- Page 1 Centrum SV... DV... TV... Installation and operating instructions 29993227 Centrum SV406 29993228 Centrum SV408 29993229 Centrum SV605 29993230 Centrum SV608 29993231 Centrum SV1004 29993232 Centrum SV1006 29993233 Centrum DV406 29993234 Centrum DV408 29993235 Centrum DV605 29993236 Centrum DV608 29993237 Centrum DV1004 29993238 Centrum DV1006 29993239...
-
Page 2: Table Of Contents
Page 1) General 2) Safety Instructions 2.1 Symbols and Signals 2.2 Risks Incurred by Failure to Comply 2.3 Operator Safety Precautions 2.4 Inspection and assembly 2.5 Modification and Spare Parts 2.6 Unauthorised Operation 3) Transport and Storage 3.1 Storage 3.2 Transport 4) Description and Operation 4.1 Description of the control Device 4.2 Operation Modes... -
Page 3: General
The use of other spare parts may Both the general safety instructions in the invalidate claims revoking the liability of Wilo for “Safety” section and those in subsequent sections any consequences. indicated by danger symbols should be carefully 2.6 Unauthorised Operation... -
Page 4: Transport
Electronic Control. Electronic Control contains an pressure. To avoid hammer effect in the system electronic regulation system using pressure and Wilo recommend you install a Wilo Cavsa Valve flow sensors and a frequency inverter. 3 pump Product Code: 2817747 sets also use a Speedcentre control panel in 4.2.4 Manual Mode (3 Pump Only) -
Page 5: Dry Run Protection
It is advisable building installation. to enter into a maintenance agreement with ATTENTION! Observe the requirements from a specialist company or with Wilo UK service the water supply companies and the local rule department. Checks should be made on the in force. -
Page 6: Warranty
7 Warranty WILO reserve the right to inspect an installation to verify that the equipment has been installed in accordance with the written instructions. The full warranty document is downloadable at www.wilo. co.uk click on local information then downloads. Before requesting a site visit, the following information must be available to the service team: •... - Page 7 Fig. 2 - Electronic Control Drive Manual Mode Inverter On (Green LED) Automatic Mode Alarm (Red LED) Menu Pump Running (Yellow LED) Enter Pump in Automatic Mode (Green LED) Value Setting Up Value Setting Down Fig. 3 - Speedcentre (3 pump only)
- Page 8 Fig. 4 - Pump Schematics Fig. 5.1 - Wiring Schematics - 1 Pump System...
- Page 9 Fig. 5.2 - Wiring Schematics - 2 Pump System...
- Page 10 Fig. 5.3 - Wiring Schematics - 3 Pump System...
- Page 11 Table 1 - Settings Menu (Hold down menu button to access) MENU SETTINGS FACTORY UNIT Language Language select English I max Set the maximum current rating of the pumps Amps Rotation Sense Change the rotation of the motors Clockwise Min Speed Minimum running speed of the motor Dry Run Prot Turn on or off the dry running protection...
- Page 12 Table 3 - Drive Fault Codes & Troubleshooting ERROR CODE BOOSTER BEHAVIOUR TROUBLESHOOT Check the hydraulic supply. The controller starts the pump every 30 minutes over 24 hours. If dry If a set point pressure higher than the E011 DRY RUN running remains, it switches off the pressure the pump can deliver is pro- pump.
- Page 13 Table 4 - Booster Troubleshooting SYMPTOM CAUSES TROUBLESHOOT Suction piping obstructed or valve Check valve opening and clean the piping on suction manifold closed if necessary The pump “fault” indicator on the control Thermal relay tripped box must be lit. Check the setting of the current Switch it again.
-
Page 14: Spares Parts
CONTROL PANEL - 2 Pump • • • • • • 29990642 CONTROL PANEL - 3 Pump • • • • • • 29990499 3 PUMP CONTROLLER SPEEDCENTRE For all spares orders or enquiries please contact Wilo spares at Email: spareparts.uk@wilo.com Ph: 01283 523000... - Page 15 EC - Declaration of conformity Herewith, we declare that Wilo-Centrum of the series Centrum SV*** Centrum DV*** Centrum TV*** (The serial number is marked on the product site plant) in its delivered state complies with the following relevant provisions: EC-Machinery Directive...
- Page 16 Wilo UK LTD Second Avenue Centrum 100 Burton on Trent Staffordshire DE14 2WJ T: +44 (0)1283 523000 E: sales.uk@wilo.com ©Copyright Wilo UK LTD 2020 www.wilo.com/gb/en...
Need help?
Do you have a question about the Centrum SV Series and is the answer not in the manual?
Questions and answers