Autonics BEN Series Manual

Autonics BEN Series Manual

Compact, amplifier built-in type with universal voltage

Advertisement

BEN Series
Compact, amplifier built-in type with Universal voltage

Features

● Small and power supply built-in type
● Easy installation with LED indicators on product
● Enables to set the operation mode by VR
(Light ON/Dark ON)
● Status and output LED indication
● Built-in IC photo diode for ambient light and electrical noise
Please read "Caution for your safety" in operation
manual before using.

Specifications

● Free power, Relay contact output type
Model
Sensing type
Sensing distance
Sensing target
Hysteresis
Response time
Response time
Power consumption
Light source
Sensitivity adjustment
Control output
Relay lifetime
Light receiving element
Indicator
Insulation resistance
Insulation type
Noise resistance
Dielectric strength
Mechanical
Vibration
Malfunction
Mechanical
Shock
Malfunction
Ambient illumination Sunlight : Max. 11,000㏓, Incandescent lamp : Max. 3,000㏓(Receiver illumination)
Environ-
Ambient temperature -20 to 65℃, storage : -25 to 70℃
ment
Ambient humidity
Protection
Material
Cable
Individual
Accessory
Common
Unit weight
※ 1: The sensing distance is specified with using the MS-2 reflector and same as the MS-4 reflector. Sensing distance is setting range of the
reflector. The sensor can detect under 0.1m.
※ 2: It is for Non-glossy white paper(100×100mm).
※ The temperature or humidity mentioned in Environment indicates a non freezing or condensation environment.
A-44
BEN10M-TFR
BEN5M-MFR
Retroreflective
Through-beam
(Standard type)
10m
0.1 to 5m
Opaque materials of
Opaque materials of Min. ø60mm
Min. ø16mm
-
Max. 20ms
24-240VAC ±10% 50/60Hz, 24-240VDC ±10%(Ripple P-P : Max. 10%)
Max. 4VA
Infrared LED(850nm)
-
Adjustment VR
Selectable Light ON or Dark ON by VR
Relay contact output
● Relay contact capacity: 30VDC 3A of resistive load, 250VAC 3A resistive load
● Relay contact composition: 1c
Mechanically: Min. 50,000,000 operation, Electrically: Min. 100,000 operation
Photo IC
Operation indicator : red, Stability indicator : green
(The red lamp on Emitter of transmitted beam type is for power indication)
Min. 20MΩ(at 500VDC megger)
Double or strong insulation (Mark :
±1,000V the square wave noise(pulse width : 1㎲) by the noise simulator
1000VAC 50/60Hz for 1minute
1.5mm amplitude or 300m/s
at frequency of 10 to 55Hz(for 1 min.) in each of X, Y, Z directions for 2 hours
2
1.5mm amplitude or 300m/s
at frequency of 10 to 55Hz(for 1 min.) in each of X, Y, Z directions for 10 minutes
2
500m/s²(approx. 50G) in each of X, Y, Z directions for 3 times
100m/s²(approx. 10G) in each of X, Y, Z directions for 3 times
35 to 85%RH, storage : 35 to 85%RH
IP50(IEC standard)
● Case, Case cover: Heat resistant ABS ● Sensing part: PC(with polarizing filter: PMMA)
ø5, 5-wire, Length: 2m(Emitter of through-beam type: ø5, 2-wire, Length: 2m)
(AWG22, Core diameter: 0.08mm, Number of cores: 60, Insulator out diameter: ø1.25)
-
Reflector(MS-2)
VR adjustment driver, Mounting bracket, Bolts/nuts
Approx. 354g
Approx. 208g
BEN3M-PFR
Retroreflective
(Built-in polarizing filter)
※ 1
※ 1
0.1 to 3m
Red LED(660nm)
, Dielectric voltage between the measured input and the power: 1kV)
(MS-4)
(MS-2)
※ MS-4 is sold separately.
BEN300-DFR
Diffuse reflective
※ 2
300mm
Translucent,
Opaque materials
Max. 20% at ratedsetting
distance
Infrared LED(940nm)
-
Approx. 195g

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BEN Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Autonics BEN Series

  • Page 1 BEN Series Compact, amplifier built-in type with Universal voltage Features ● Small and power supply built-in type ● Easy installation with LED indicators on product ● Enables to set the operation mode by VR (Light ON/Dark ON) ● Status and output LED indication ●...
  • Page 2 Amplifier Built-in type with Universal voltage ● DC power, Solid state output type Photo electric Model BEN10M-TDT BEN5M-MDT BEN3M-PDT BEN300-DDT sensor Retroreflective Sensing type Through-beam Retroreflective Diffuse reflective (with polarizing filter) Fiber optic ※ 1 ※ 1 ※ 2 Sensing distance 0.1 to 5m 0.1 to 3m 300mm...
  • Page 3 BEN Series Feature data Retroreflective type(Standard type) Retroreflective type(Built-in polarizing filter) ● BEN5M-MFR ● BEN5M-MDT ● BEN3M-PFR ● BEN3M-PDT Parallel shifting characteristic Parallel shifting characteristic Measuring method Data Measuring method Data Operation level Operation level Reflector(MS-2) Reflector(MS-2) Stable operation level Stable operation level ℓ...
  • Page 4 Amplifier Built-in type with Universal voltage Operation mode Diffuse reflective type Photo ● BEN300-DFR ● BEN300-DDT electric sensor Operation mode Light ON Sensing area characteristic Fiber Received light optic Receiver operation sensor Measuring method Data Interrupted light Standard sensing target: Operation indicator Operation level Door/Area...
  • Page 5 BEN Series Connections Through-beam Retroreflective Diffuse reflective ● BEN5M-MFR(Standard type) ● BEN10M-TFR1 ● BEN10M-TFR2 ● BEN300-DFR ● BEN3M-PFR(Built-in polarizing filter) 24-240VAC±10% 24-240VAC±10% 24-240VAC±10% 24-240VDC±10% 24-240VDC±10% 24-240VDC±10% Reflector (Brown) (MS-2) (Blue) (Brown) (Blue) (Brown) (Blue) Sensing Sensing target target Emitter Receiver...
  • Page 6 Amplifier Built-in type with Universal voltage Mounting and sensitivity adjustment Photo electric sensor Through-beam type Retroreflective type 1. Supply the power to the photoelectric sensor, after 1. Supply the power to the photoelectric sensor, after Fiber optic setting the emitter and the receiver facing each other. setting the photoelectric sensor and the reflector(MS-2) sensor 2.

This manual is also suitable for:

Ben10-tfrBen5m-mfrBen3m-pfrBen300-dfr

Table of Contents