Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Binks QS-5012-CE
Summary of Contents for Binks QS-5012-CE
- Page 1 SBBI-E-19-095 iss1 AIR MOTOR DRIVES and AGITATORS for PRESSURE FEED TANKS IMPORTANT: Read and follow all instructions and SAFETY PRECAUTIONS before using this equipment. Retain for future reference. P 1 - 12 P 24 - 34 P 13 - 23 P 35 - 45 P 46 - 56 Page 1...
-
Page 2: Atex Classification
Includes air adjusting for speed control with hose and fittings for tank regulator connection. QMS-431-CE, 433-CE and 434-CE Agitator for use with QS-5012-CE Gear reduction drive on 2, 10 and 15 gall tanks models. Alternatively can be used without a drive motor for manual operation. - Page 3 4. Use lubricating medium resistant to carburisation and has an auto ignition temperature of more than 185ºC for T4 equipment. 5. User shall verify the presence of gearbox lubricant (QS-5012-CE only) in accordance with the instructions on P5, before operating the air motor.
-
Page 4: Installation
1. These instructions are for fitting of the lid. Fully tighten with a spanner (1.875 Wait until all the air has escaped through the QS-5012-CE drive unit to an installed AF). valve before removing the pressure tank QMS-431-CE,... -
Page 5: Operation
Tank (Fig. 9) pressure must relieved using QS-5012-CE Operation (Fig. 5) following steps: 1. Follow the pressure relief procedure at the start of the INSTALLATION section. 1. Turn off the main air supply to the tank. 2. Unscrew the centre blanking plug from Fig 3 2. -
Page 6: Replacement Of Parts
(94) and fit key (95) before installation section. pressure 0.7bar (10psi) and re-start the engaging the motor to the gearbox. 16. Re-fit the drive motor QS-5012-CE as motor. Run until no more traces of Apply thread locking compound to the per installation section. - Page 7 end plates and rotor assembly. If scoring 17.5mm (11/16”) then re-new the vanes. free up and center the rotor in the body. exists, send unit to a Gast Authorized Install new vanes (44), the angle cuts on 18. Apply a small amount of grease to Service Facility.
- Page 8 Ref. Replacement Description Individual Fig 5 Part No. Parts Req. 53 350-401 Air Strainer Strainer Cap + 55 Screen · + 56 Felt Strainer Body 58 - Gearbox Assembly (see fig 6) 59 32243-133 Washer 60 QMS-35 Air Motor Support 61 - Cap screw 3/8”...
- Page 9 QMS-431, 433 and 434 AGITATOR PARTS LIST Fig 7 Ref. Part No. Description No of Parts Req. QMS-431-CE Agitator Assembly 8L (includes items 20 to 31) QMS-433-CE Agitator Assembly 40L QMS-434-CE Agitator Assembly 60L QMS-46 Retaining Nut QMS-447 Thrust Collar Kit (includes items 22 and 23) —...
- Page 10 Parts list for PT-427-CE, PT-418-CE, Ref. Replacement Part Description Individual Parts Req. PT-419-CE & PT-428-CE PT-410 * 35 Air Motor Assembly QMS-455 QS-190 Fig 8 End Cap PT-65 * 37 ——– End Cap Gasket 38 PT-58 Bearing 39 ——– Screw (1/4”-28 x 1/2”) * 40 ——–...
- Page 11 Parts list for QMS-430-CE Ref. Replacement Description Individual Part No. Parts Req. Fig 9 Street Elbow 1/4”(M) 19 ——-- 1/4”NPT(F) 20 H-2008 Nipple 1/4” NPS(M) 21 HAV-500 Air Adjusting Valve 22 HA-57001 Hose assembly 23 ——- Service Tee 1/4” 32A KK-4991 Agitator Kit Motor Assembly (incl parts 33 QMS-428...
-
Page 12: Service Checks
Service Checks Condition Cause Correction Air motor is sluggish or rotates Dirt or foreign object trapped in the Flush the motor, or strip motor and slowly or stops motor or from Internal corrosion clean as instructed on P4 Air motor runs hot and slows down Vanes misaligned Strip and rebuild motor Air motor runs slowly...
Need help?
Do you have a question about the QS-5012-CE and is the answer not in the manual?
Questions and answers