Related Manuals for NEC NP01LK
Summary of Contents for NEC NP01LK
- Page 1 Support Kit Handling Instructions Model NP01LK サポートキット取扱説明書 NP01LK 型名 支撑套件操作说明书 NP01LK 型号...
-
Page 2: Table Of Contents
CONTENTS Introduction ..............3 CAUTION .................4 Things to prepare ............4 Included items ...............5 Preparation ..............6 How to install the support kit ........7 Adjusting the focus ...........14 Throw distance ............17 目次 はじめに ................3 注意 ...................4 用意するもの ..............4 同梱品 ................5 準備 ...................6 サポートキッ トの取り付け方 ........7 フォーカス調整... -
Page 3: Introduction
( English ) Introduction This is the handling instructions of the support kit for the fixed focus lens, NP44ML, describing how to attach the support kit and how to adjust the focus. This instructions also includes tables of throw distances of the lens unit mounted on the projector. About the procedures for mounting the lens unit, please refer to the projector User’s Manual. -
Page 4: Caution
CAUTION • After installing the lens unit, be sure to secure it to the projector using the support kit. Fail- ure to do so could cause the lens unit to fall, resulting in injury. • Power off the projector and unplug the power cord before installing the lens unit and the support kit. Things to prepare • Phillips head screwdriver • For ceiling mount or portrait position, a mounting bracket with sufficient strength to support the combined weight of the projector, the lens unit, and the support kit 注意 • レンズユニッ トを取り付けた後は、必ずサポートキッ トを使ってレンズユニッ トをプロジェク ター本体に固定してください。固定しないと、レンズユニットが落下して、けがの原因とな ります。 • レンズユニットとサポートキットの取り付けは、プロジェクターの電源を切り、電源プラグ をコンセントから抜いた状態で行ってください。 用意するもの •... -
Page 5: Included Items
Included items Support bracket Screw 8 pcs Adapter (A) For PA803U/PA723U/PA653U/PA853W/PA703W/PA903X Adapter (B) For PA803UL/PA703UL/PA653UL 同梱品 サポート金具 ネジ ８本 アダプター (A) NP-PA803UJL/NP-PA723UJL/NP-PA653UJL/NP-PA853WJL/NP-PA703WJL/NP-PA903XJL 用 アダプター (B) NP-PA803ULJL/NP-PA703ULJL/NP-PA653ULJL 用 内含物品 支撑支架 螺钉 ８个 适配器 (A) 适用于 NP-PA803U+/NP-PA653U+/NP-PA853W+/NP-PA753W+/NP-PA703W+/NP-PA653W+/ NP-PA903X+/NP-PA803X+/NP-PA703X+ ... -
Page 6: Preparation
Preparation Return the projector lens position to the home position without the lens mounted. For details on connecting the power cord and turning on/off, refer to the projector User’s Manual. Connect the power cord to the projector. For PA803U/PA723U/PA653U/PA853W/PA703W/PA903X, press the (POWER) button to turn on the power to the projector. For PA803UL/PA703UL/PA653UL, do not press the (POWER) button. Press and hold the ZOOM/L-CALIB button for 2 seconds or longer. ... -
Page 7: How To Install The Support Kit
How to install the support kit The following explanation uses the case of PA803U as an example. 1. Turn over the projector. Lay down the projector cabinet upside down on a table with soft cloth laid. While doing this, align the front of the projector with the end of the table. CAUTION • For moving the projector, make sure you have at least two people. Attempting to move the projector alone could result in back pain or other injuries. サポートキッ... - Page 8 2. Fix the adapter to the lens unit. As describing on the illustration, put the adapter (A) on the lens unit whose protrusions meet with the screw holes on the adapter and fasten them by 2 screws. • For PA803UL/PA703UL/PA653UL, use the adapter (B). The attaching procedure is the same as the above. NOTE: Do not touch the glass on the lens unit. 2. レンズユニットにアダプターを取り付ける。 アダプター...
- Page 9 3. Adjust the tilt of the lens unit. Adjust the focus balance at the periphery of the projected image. For table use: Move the tilt lever to the “+” position. For ceiling use: Move the tilt lever to the “-“ position. For other uses: Move the tilt lever to the center (around “T” letter). 3. レンズユニットのチルト調整を行う 投写画面の周辺部分のフォーカスバランスを調整します。 テーブルに設置する場合：チルトレバーを＋の位置に合わせます。 天吊りで設置する場合：チルトレバーを−の位置に合わせます。 上記以外で設置する場合：チルトレバーを中央（T の文字付近）に合わせます。 3. 调整镜头单元的倾斜度。 调整投影图像外围的聚焦平衡。 对于在桌上使用 ： 将倾斜杆移动到 “+”位置。 对于在天花板上使用 ： 将倾斜杆移至 “ - ”位置。 对于其他用途 ： 将倾斜杆移动至中心 （ “T”字母周围） 。...
- Page 10 4. Mount the lens unit on the projector and adjust the lens position According to the instructions on the projector User’s Manual, mount the lens unit onto the projector. Connect the power cord to the projector and power it on. ...
- Page 11 5. Adjust the support bracket. Loosen the wing nut on the support bracket and pull out the L-shaped metal fitting. Rotate the dial to align its hole with its top position. 6. Fix the support bracket to the projector. As shown on the illustration, place the support bracket and use four screws to tighten them.
- Page 12 ピン 插针 7. Connect the support bracket to the adapter. Move the L-shaped metal fitting of the support bracket to meet with the adapter, and insert the adapter pin into the hole of dial. When doing this, make sure that the L-shaped metal fitting and the adapter are so securely fixed that the adapter pin can be seen through the hole of dial. 7. サポート金具とアダプターを接続する。 サポート金具のＬ字型の金具を動かしてアダプターに当て、アダプターのピンをダイヤル の開口に入れます。 このとき、Ｌ字型の金具とアダプターが確実に付いて、ダイヤルの開口からピンが見えて いることを確認してください。 7. 将支撑支架连接至适配器。 移动支撑支架的 L 形金属配件，使其与适配器相对接，并将适配器插针插入拨盘的孔中。 在执行此操作时，请确保稳固安装...
- Page 13 8. Tighten a screw to fix the support bracket and the adapter. Tighten two screws to fix the L-shaped metal fitting and the adapter. Tighten the wing nut. This completes mounting the support kit. After installing the projector, connect the power cord and video cables, and then turn on the projector. Finally, adjust the focus. 8. サポート金具とアダプターをネジでしめ付ける。 ...
-
Page 14: Adjusting The Focus
Adjusting the focus 1. Press the FOCUS button on the cabinet. The LENS FOCUS control screen will be displayed on. * In another way, press and hold the CTL button and then press VOLUME/ FOCUS +/- button on the remote control. 2. When the cursor is on the CENTER on on-screen menu, press either ◀ or ▶ button to align focus of screen center. フォーカス調整... - Page 15 3. Press the ZOOM/L-CALIB button on the cabinet. The LENS ZOOM control screen will be displayed on. * In another way, press and hold the CTL button and then press D-ZOOM/ZOOM +/- button on the remote control. 4. Press either ◀ or ▶ button to align the focus of screen peripheral area. 3. プロジェクター本体の ［ZOOM/L-CALIB］ボタンを押す。 ズーム調整画面が表示されます。 • リモコンで操作する場合は ［CTL］ボタンを押したまま ［部分拡大／ズーム＋ / −］ボタンを 押します。 4.
- Page 16 5. Adjust the tilt Loosen the two screws that were tightened in “7. Connect the support bracket to the adapter”. Use your hand or a Phillips head screw driver to rotate the dial of the support bracket, and then adjust the vertical focus balance of the projected image. Tighten the two screws that were loosened in step . Follow 1 to 4 of “Adjusting the focus” to re-adjust the focus and check if you have obtained the best focus balance in the vertical direction. This completes adjusting the focus. 5.
-
Page 17: Throw Distance
Throw distance ① • Throw distance shows a distance between the center of the lens unit projection win- ② dow and the screen face. (Unit: m) • Figures are designed values. They can vary depending on the lens unit. ③ 投写距離 • 投写距離は、レンズユニット投写窓中心か ら投写画面までの距離です。 （単位：m） • 各数値は設計値です。レンズユニットによ りばらつきがあります。 ④ 投射距离 • 投射距离表示镜头投射窗中心与屏幕表面 之间的距离。... - Page 18 PA803U/PA723U/PA653U NP-PA803UJL/NP-PA723UJL/NP-PA653UJL NP-PA803U+/NP-PA723U+/NP-PA653U+ Screen size (inch) スクリーンサイズ（型） 屏幕尺寸 ( 英寸 ) 0.15 0.67 0.59 1.89 0.17 0.70 0.60 1.95 0.32 0.84 0.70 2.31 0.54 1.06 0.84 2.86 0.76 1.28 0.98 3.40 0.90 1.43 1.07 3.77 1.20 1.72 1.26 4.49 1.42 1.94 1.40 5.04 1.64 2.16...
- Page 19 PA903X NP-PA903XJL NP-PA903X+/NP-PA803X+/NP-PA703X+ Screen size (inch) スクリーンサイズ（型） 屏幕尺寸 ( 英寸 ) 0.15 0.68 0.47 2.02 0.18 0.70 0.49 2.07 0.29 0.81 0.54 2.37 0.50 1.02 0.64 2.93 0.71 1.23 0.74 3.49 0.85 1.37 0.81 3.86 1.13 1.66 0.95 4.61 1.35 1.87 1.05 5.17 1.56 2.08...
- Page 20 © NEC Display Solutions, Ltd. 2018-2019 Printed in Japan 7N8N9514...