Omnitron Systems iConverter GM3 Quick Start Manual

2 and 3 port network interface devices

Advertisement

Quick Links

iConverter
2 and 3 Port GM3
®
Network Interface Devices
Quick Start Guide
38 Tesla, Irvine, CA 92618 USA
Phone: (949) 250-6510; Fax: (949) 250-6514
General and Copyright Notice
This publication is protected by U.S. and international copyright laws. All rights
reserved. The whole or any part of this publication may not be reproduced, stored
in a retrieval system, translated, transcribed, or transmitted, in any form, or by
any means, manual, electric, electronic, electromagnetic, mechanical, chemical,
optical or otherwise, without prior explicit written permission of Omnitron Systems
Technology, Inc.
The following trademarks are owned by Omnitron Systems Technology, Inc.:
FlexPoint
, FlexSwitch
, HybridNID
TM
TM
OmniLight
, OmniConverter
, RuggedNet
®
®
OST
and the Omnitron logo.
TM
All other company or product names may be trademarks of their respective owners.
The information contained in this publication is subject to change without notice.
Omnitron Systems Technology, Inc. is not responsible for any inadvertent errors.
Warranty
This network product and the included AC/DC power adapter are warranted to the
original purchaser (Buyer) against defects in material and workmanship for a period
of two (2) years from the date of shipment. The warranty for the network product can
be extended to three (3) years by registering the product at www.omnitron-systems.
com/support within ninety (90) days from the date of shipment. During the warranty
period, Omnitron will, at its option, repair or replace a product which is proven to be
defective with the same product or with a product with at least the same functionality.
For warranty service, the product must be sent to an Omnitron designated facility,
at Buyer's expense. Omnitron will pay the shipping charge to return the product
to Buyer's designated US address using Omnitron's standard shipping method.
Limitation of Warranty
The foregoing warranty shall not apply to product malfunctions resulting from
improper or inadequate use and/or maintenance of the equipment by Buyer, Buyer-
supplied equipment, Buyer-supplied interfacing, unauthorized modifications or
tampering with equipment (including removal of equipment cover by personnel not
specifically authorized and certified by Omnitron), or misuse, or operating outside
the environmental specification of the product (including but not limited to voltage,
ambient temperature, radiation, unusual dust, etc.), or improper site preparation
or maintenance.
No other warranty is expressed or implied. Omnitron specifically disclaims the implied
warranties of merchantability and fitness for any particular purpose.
The remedies provided herein are the Buyer's sole and exclusive remedies. Omnitron
shall not be liable for any direct, indirect, special, incidental, or consequential
damages, whether based on contract, tort, or any legal theory.
, iConverter
, miConverter
, NetOutlook
®
®
TM
, Omnitron Systems Technology, Inc.
®
Page 2
,
®
,
TM

Advertisement

Table of Contents
loading

Summary of Contents for Omnitron Systems iConverter GM3

  • Page 1 Omnitron Systems Technology, Inc. The following trademarks are owned by Omnitron Systems Technology, Inc.:...
  • Page 2: Product Overview

    Directive) of the European Community directive 2012/19/EU on waste electrical and electronic equipment (WEEE) which, together with the RoHS Directive 2015/863/ The iConverter GM3 is an intelligent Network Interface Device (NID), that delivers EU, for electrical and electronic equipment sold in the EU after July 2019. Such...
  • Page 3: Serial Console Port

    Serial Console Port 1) Configure DIP-switches The module can be configured by attaching the serial port to a DB-9 serial (RS-232) The GM3 has two banks of DIP-switches. The location of the DIP-switches is equipped computer with terminal emulation software such as ProComm or Putty. The illustrated below.
  • Page 4 SW1: P1 Auto/Manual Negotiation “AN/MAN” - All Models SW3, SW4 and SW5: Reserved - SFP/SFP Model When this DIP-switch is in the “AN” position (factory default), the port automatically These DIP-switches are reserved and must be in the DOWN (default) position. determines the duplex and pause modes of the connected remote device.
  • Page 5 SW1, SW2 - P1, P2 Auto/Manual Negotiation “AN/MAN” Function When these DIP-switches are in the “AN” position (factory default), the port RTP/OFF NORM / 1:1 automatically determines the duplex and pause modes of the connected remote RTP (DOWN) NORM (DOWN) Non-redundant mode - independent mode device.
  • Page 6: Installing The Module

    DIP-switch Bank 2 Settings: All 2 and 3-Port Models 2) Installing the Module The function of DIP-switch Bank 2 is outlined in the table below. Wall Mounting - Standalone Module The wall mounting height of the module should be less than or equal to 2 meters Switch Description DOWN (Default)
  • Page 7 3) Apply Power WARNING: Only a DC power source that complies with AC Power - Standalone Modules safety extra low voltage (SELV) requirements can be connected to the DC-input power supply. Secure the ground wire to the ground screw located on the back of the module. Route the power cord through the provided strain relief for additional support and connect the barrel connector at the end of the wire on the AC/DC adapter to the barrel WARNING REGARDING EARTHING GROUND:...
  • Page 8: Verify Operation

    5) Verify Operation WARNING!!! Verify the module is operational by viewing the LED indicators. NEVER ATTEMPT TO OPEN THE CHASSIS OR SERVICE THE POWER SUPPLY. OPENING THE LED Function Color OFF State ON/Blinking State CHASSIS MAY CAUSE SERIOUS INJURY OR DEATH. “Legend”...
  • Page 9 LED Function LED Legend/State Color OFF State ON/Blinking State Link Speed “Legend” “1000” “100” Power Green No power ON: Module has power Port not linked “PWR” Port linked at 100Mbps P1 Link Activity ON: Port linked at 1000M Green Port not linked at 1000M “1000”...
  • Page 10: Specifications

    Chassis Backplane: 2-Port: 1.6A @ 3.3VDC DC Power Requirements (Plug-in) 3-Port: 2.0A @ 3.3VDC Address: Omnitron Systems Technology, Inc. Terminal: 2-Pin Terminal (non-isolated) 38 Tesla 8 - 32VDC inclusive of tolerance Irvine, CA 92618, USA 0.6A @ 9VDC (typical), 0.45A @ 12VDC (typical)

Table of Contents