Advertisement
2018-2019 Ford Mustang Ecoboost OEM-Style Fog Light Kit
Parts List:
LED Foglight Assemblies
(if you ordered part#3601)
Wiring harness
Ford OEM Switch
PB-3601 Parts Bag
Thank you for purchasing one of our products. Please familiarize yourself with the parts included as well
as the instructions before attempting installation. Please seek the help of a certified technician if you feel
unable to complete the installation safely and properly. Failure to read and follow the instructions below
may result in personal injury or damage to property. Starkey Products, Inc. and our retailers assume no
liability for failures to comply with guidelines and warnings outlined in this instruction manual.
If you are receiving this instruction manual with part #3651 (Starkey Fog Light Wiring & Switch Kit),
skip to the 'Wiring in Engine Bay' section on page 2. Otherwise, begin steps immediately below.
Fog light installation into bumper:
Removing the bumper is not necessary. Driving the vehicle onto ramps or raising the front end of the
car will greatly ease installation. Before beginning the steps below, turn off the car, remove key, and
engage the emergency brake.
1. Open hood of car and make sure hood is held open securely.
2. Removing the air deflector will allow you access to fog light mounting points. The air deflector is
held on by 17 screws and 2 push pins (shown as dots in picture 1 below). Use a ratchet & 7mm
socket OR wrench to remove the screws. The pins are removed with a flat head screwdriver - pry
up on center part of the pin and then pry up on the body of the pin. See picture 2.
3. Use flathead screwdriver to remove the 3 lower push pins in each wheel well. These push pins
help support the air deflector. Save for re-installation later. The deflector is removed by pulling
back/ down gently. Set aside hardware and deflector for re-attachment later.
4. Unplug connectors on each lamp.
5. Remove 3 screws holding each lamp assembly in place and carefully remove lamp assembly. See
picture 3.
6. Install new lamp. Re-use 3 mounting screws.
Remove air deflector. It is held on
by 17 screws/ 2 push pins.
Quantity:
2
1
1
1
Pry up on center part of pin first.
1
Then pry out entire push pin.
Part Number: 3601 / 3651
Tool List:
Flat head & Phillips screwdriver
Ratchet & Socket set OR
Adjustable Wrench
Wire stripping tool or razor blade
Unplug wiring & remove 3
2
screws holding lamp on.
© 2019 Starkey Products, Inc.
3
Page 1
Version 1.0
Advertisement
Table of Contents
Related Manuals for Starkey 3601
Summary of Contents for Starkey 3601
- Page 1 Failure to read and follow the instructions below may result in personal injury or damage to property. Starkey Products, Inc. and our retailers assume no liability for failures to comply with guidelines and warnings outlined in this instruction manual.
- Page 2 Part Number: 3601 / 3651 Remove black panel shown. Save Be sure that the nut is re-attached Make sure tan fuse is seated 8 retaining pins for re-install later. tightly. properly in slot (position 66). Wiring in Engine Bay: 1. Remove the battery cover on the passenger side. It is held on by 3 caps that you can unscrew by hand.
- Page 3 Part Number: 3601 / 3651 Pry downward with screwdriver 4 clips hold switch in. 2 clips are Connect wire tap to pin # 14 wrapped in a rag. shown above. shown by solid black dot above. 10. Route the wiring for the driver side fog light/ switch over the radiator along the frame of the car.
- Page 4 Part Number: 3601 / 3651 Cut the gray wire (pin#14) 2 Strip 1/4” of the insulation off Slide red cap from connector onto inches from the connecter. each end of the wire you cut. gray wire and then re-attach. At this point we will connect the green wire from the fog light wiring harness to the correct wire behind the headlight switch connector.
- Page 5 Part Number: 3601 / 3651 Final Installation: 1. Re-connect the negative battery cable to the car battery. Remember to re-tighten the bolt. 2. Double check everything to make sure it was connected properly. Now press the Engine Start button. Test the fog light switch to make sure the lights turn ON and OFF. If the lights do not power on or do not turn off with the switch, visit the trouble shooting section below.
- Page 6 Limited Warranty: This warranty covers defects in materials or workmanship in any component sold by Starkey Products, Inc. or its authorized dealers. Warranty is effective for five years from the date of purchase. Coverage terminates if you sell or transfer ownership of the product.
Need help?
Do you have a question about the 3601 and is the answer not in the manual?
Questions and answers