Advertisement
2013-2014 Ford Mustang GT-Style Fog Light Conversion Kit
Parts List:
Fog light (Left & Right)
Upper grille with surround
Lower grille
Wiring harness extenders (set)
PB-3506 Parts bag
Thank you for purchasing one of our products. Please familiarize yourself with the parts included as well
as the instructions before attempting installation. Please seek the help of a certified technician if you feel
unable to complete the installation safely and properly. Failure to read and follow the instructions below
may result in personal injury or damage to property. Starkey Products, Inc. and our retailers assume no
liability for failures to comply with guidelines and warnings outlined in this instruction manual.
This kit is designed for 2013 V6 Mustangs or GT California Special Mustangs that came with lower
valance fog lamps from the factory. If your Mustang did not come with fog lights from the factory, you
will also need Starkey part number 3551 (wiring and OEM switch kit) to power your LED fog lamps.
Removing the bumper:
Removing the bumper is necessary. Although it may sound daunting, it is actually quite simple.
Driving the vehicle onto ramps or raising the front end of the car will greatly ease installation. Before
beginning the steps below, turn off the car, remove key, and engage the emergency brake.
1. Removing the splash/ rock guard is the first step to removing the bumper. The splash guard has 17
screws holding it in place. Use a ratchet & 8mm socket OR Phillips screwdriver to remove the 6
screws closest to the front (nose) of the car. Use a 7mm socket to remove the remaining 11 screws.
After the 17 screws are removed splash guard can be detached by pulling back/ down gently. Set
aside 17 screws and splash guard for re-attachment later. See picture 1.
2. After removing the splash guard, unplug the turn signal indicator lamps. These are disconnected
by squeezing the clip where the wires enter the connector.
Black splash guard should be
removed. It is held by 17 screws.
Quantity:
2
1
1
1
1
Remove black panel shown. Save 8
retaining pins for re-install later.
Part Number: 3506
Tool List:
Flat head & Phillips screwdriver
•
Ratchet & Socket set OR
•
Adjustable Wrench
•
Small knife
•
Pry up on center part of pin first. Then
pry out entire retainer pin.
© 2012 Starkey Products, Inc.
Page 1
Version 1.2
Advertisement
Table of Contents
Related Manuals for Starkey 3506
Summary of Contents for Starkey 3506
- Page 1 If your Mustang did not come with fog lights from the factory, you will also need Starkey part number 3551 (wiring and OEM switch kit) to power your LED fog lamps. Removing the bumper: Removing the bumper is necessary.
- Page 2 If the black Styrofoam came off, simply re-attach it with the 4 ribbed push pins. See picture 7 below. The following steps will explain how to remove the upper and lower grille. Take your time during this part of the installation. Page 2 Version 1.2 © 2012 Starkey Products, Inc.
- Page 3 See picture 11. Top row of tabs shown. Pry up with 3 screws hold on each fog lamp. Use screwdriver while pushing tab down. 5/16 socket or flat head to tighten. Page 3 Version 1.2 © 2012 Starkey Products, Inc.
- Page 4 Inc. or its authorized dealers. Warranty is effective for five years from the date of purchase. Coverage terminates if you sell or transfer ownership of the product. Starkey Products will repair or replace the defective or malfunctioning product or any defective or malfunctioning part thereof at no charge. This warranty covers parts and labor only.
Need help?
Do you have a question about the 3506 and is the answer not in the manual?
Questions and answers