Download Print this page

Yamaha CX-1 Owner's Manual: Features; Supplied Accessories

Natural sound stereo pre-amplifier.
Hide thumbs

Advertisement

Caution: Read this before operating your unit
1
To ensure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2
Install your unit in a cool, dry, clean place – away from
windows, heat sources, and too much vibration, dust,
moisture or cold. Avoid sources of hum (transformers,
motors). To prevent fire or electrical shock, do not
expose to rain and water.
3
Do not operate the unit upside-down. It may overheat,
possibly causing damage.
4
Never open the cabinet. If a foreign object drops into
the set, contact your dealer.
5
Always set the volume control to "–
the audio source play: increase the volume gradually to
an appropriate level after the play is started.
1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product
MUST be used. Follow all installation instructions.
Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class "B" digital devices. Compliance with
these requirements provides a reasonable level of
assurance that your use of this product in a residential
environment will not result in harmful interference with
other electronic devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.

FEATURES

Continuously Variable Loudness Control
>
only
PURE DIRECT Switch to Reproduce the Purest Source
Sound
SUBSONIC FILTER Switch to Cut Out Undesirable Ultra-
Low-Frequency Signals

SUPPLIED ACCESSORIES

After unpacking, check that the following parts are contained.
Remote Control Transmitter.
<
>
<
>
CX-1
CX-2
PHONO
POWER
+
PRESET
A/B/C/D/E
TUNER
CD
SKIP
PLAY
SEARCH
PAUSE/STOP
DISC SKIP
DIR A
DECK A/B
DIR B
AUX
PLAY
TAPE 1
C H A P T E R
C H A P T E R
REC/PAUSE
STOP
REC MUTE
TAPE 2
TAPE 3
REC
REC/PAUSE
PAUSE
DIR A
DIR A
DIR B
DIR B
TAPE 1
TAPE 1
REC MUTE
REC MUTE
TAPE 2
TAPE 2
MUTING
+
MUTE
MUTE
VOLUME
A
B
C
D
E
F
" before starting
FCC INFORMATION
<
For CX-2
Batteries
Audio Connection Cord
6
Do not use force on switches, knobs or cords. When
moving the set, first turn the unit off. Then gently
disconnect the power plug and the cords connecting to
other equipment. Never pull the cord itself.
7
Do not attempt to clean the unit with chemical solvents;
this might damage the finish. Use a clean, dry cloth.
8
When not planning to use this unit for long periods of
time (ie., vacation, etc.), disconnect the AC power plug
from the wall outlet.
9
Be sure to read the "Troubleshooting" section on
common operating errors before concluding that your
unit is faulty.
10
Do not connect audio equipment to the AC outlets on
the rear panel if that equipment requires more power
than the outlets are rated to provide.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit "OFF" and "ON", please try
to eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
PHONO (MM/MC) Selector Switch
Video Signal Input/Output Capability (Including S Video
<
Connections)
For CX-2 only
Remote Control Capability
REMOTE CONTROL Connector to Make the Power of
the Power Amplifier MX-1 or MX-2 Controlled by This
Unit
>
Remote Control Cable
3

Advertisement

   Related Manuals for Yamaha CX-1

This manual also for:

Cx-2

Comments to this Manuals

Symbols: 0
Latest comments: