LG LDP6797 Series Quick Install page 2

HOME APPLIANCES
LG DISHWASHERS
LDP6797_
Top Control Dishwasher with QuadWash™
QUICK INSTALL & CLEARANCES
For full installation directions/clearances please refer to
the corresponding User Manual and Installation Guide.
DIMENSIONS / CLEARANCES
Product Dimensions (in) (W x H x D)
Depth with Door Closed with Handle (in)
Depth with Door Open (in)
Carton Dimensions (in) (W x H x D)
POWER RATINGS
ENERGY STAR® Qualified
CEE Tier
Energy Use (kWh/Year)
Water Factor (WF)
PREPARING ELECTRICAL WIRING
•
Operate this appliance with the correct voltage as shown in your User Manual and
on the rating plate. Connect it to a dedicated, properly grounded branch circuit
which is protected by a time delay fuse. Connect the appliance using 3-wires,
including a ground wire.
•
If an outlet and other power connector are used, it should be in an accessible
location adjacent to
and not behind the
dishwasher and within
4 ft. of the dishwasher's
side.
•
The wiring must be
grounded properly. If in
doubt, have it checked
by a qualified electrician.
Do not connect any other
appliance to the same
outlet.
•
Route the wiring.
•
Make sure the electrical
cable is oriented in the
right side channel.
▲
WARNING
!
•
For personal safety, remove house fuse or open circuit breaker before installation.
•
Do not use an extension cable or adapter with this dishwasher
•
If you find any damage to the dishwasher, contact your retailer or contractor.
© 2018 LG Electronics USA, Inc. All rights reserved. "LG Life's Good" is a registered trademark of LG Corp. All other product and brand names are trademarks or registered trademarks of their respective owners. Design, features and specifications are subject to
change without notice. Non-metric weights and measurements are approximate. Some features may require Internet access. Content and services may vary by product and are subject to change without notice. 10/22/18
23 3/4" x 33 3/5" x 24 3/5"
24 5/8"
50 1/2"
28" x 34 7/10" x 29 3/5"
Yes
1
258 kWh
2.8
Electrical cable
4 1/2" - 6"
PREPARING CABINET OPENING
•
This dishwasher is designed to fit a standard dishwasher opening.
An opening may be needed on both sides to route plumbing and
electrical connections.
•
Select a location as close to the sink as possible for easy connections to water and
drain lines.
•
To ensure proper drainage,
install the dishwasher no more
than 12 ft. from the sink.
•
If installing the dishwasher in a
corner, leave a minimum of 2"
between the dishwasher and
the adjacent wall.
•
To allow for proper clearance
of plumbing and electrical, use
the template included with
the literature to determine
the clearance on the side of
the cabinet where the cabinet
meets the back wall. Using a 2
1/2" diameter hole saw, drill a
hole in the target area as shown
on the template.
▲
WARNING
!
Don't use existing holes unless they are in the target area. Otherwise, the water
supply and drain hose may be damaged by being crushed or kinked.
▲
! CAUTION
Failure to properly locate the hole for the water and drain lines may prevent the
dishwasher from installing flush with the cabinets and could result in kinked or
damaged lines. Installation damage is not covered by the warranty, and leaks caused
by improper installation may result in property damage.
PREPARING WATER SUPPLY CONECTION
•
Make sure the house water supply is turned off before connecting
the dishwasher water lines.
•
Connect the dishwasher to a hot water supply with a temperature range between
120 °F (49 °C) and 149 °F (65 °C). This temperature range provides the best
washing results and shortest cycle time. To prevent damage to dishes, the
temperature should not
exceed 149 °F (65 °C).
•
When connecting the
dishwasher water
line, sealing tape or
compound should be
used on pipe threads
to avoid leaks. Tape or
compound should not
be used on compression
fittings.
•
The water supply tube
must be located in the
6 1/2" - 7 1/4"
left side channel.
Water supply line
NOTE
Use new hoses when connecting to the water supply. Do not reuse old hoses.