BrassCraft CSSL Instructions Manual page 3

DANGER: DO NOT USE motorized
equipment or other sources of
combustion to dissipate gas vapors.
Motorized equipment can ignite gas
vapors causing fire or explosion
which may result in property
damage and/or personal injury
including death. (Figure N)
DANGER: Fuel gases are colorless,
tasteless and in its pure state, odorless.
They are odorized (rotten egg smell) so that their presence can be detected. LP
gases are heavier than air and dissipate slower than natural or manufactured
gases. LP gas, if released in quantity, will accumulate in low-lying areas such as
a basement or crawl space.
®
THIS SAFETY+PLUS EXCESS FLOW VALVE (included with the connector) IS NOT
DESIGNED TO ACTIVATE IF ANY OF THE FOLLOWING CONDITIONS ARE PRESENT:
• There are small leaks such as pin hole leaks or lesser leaks caused by cracks
or loose connections that do not increase the gas flow above normal operating
capacity of the appliance.
• The gas appliance malfunctions or the user fails to shut off gas burners.
• There is foreign matter, such as pipe thread sealant, lodged in the valve.
• The manual gas shut-off valve is partially opened, or there is a pipe break or
damage that has occurred upstream of the Safety+PLUS
prevents sufficient gas flow through the valve.
• There is insufficient gas flow from an improperly sized gas piping system
upstream of the Safety+PLUS valve.
• The gas flow through the valve is in the wrong direction. The excess flow valve
responds to gas flow in one direction only (see product label). The valve must be
installed so that the arrows point in the direction of gas flow.
• The Safety+PLUS valve is damaged, exposed to fire or improperly installed.
WARNING: Replace the Safety+PLUS
to fire.
®
WARNING: Safety+PLUS
EXCESS FLOW VALVE is only intended for use with
packaged connector.
©2019 Brasscraft Manufacturing Company
®
excess flow valve that
®
valve if it has been damaged or exposed
Brasscraft Manufacturing Company, 39600 Orchard Hill Place Novi, Michigan 48375-5331
TOLL-FREE: 877.272.7755 FAX: 248.305.6011 www.brasscraft.com
Manufacturer assumes no responsibility for failure due to improper installation.
©2019 Brasscraft Manufacturing Company, Novi, MI 48375-5331 U.S.A. All Rights Reserved.
www.brasscraft.com Designed, Machined and Assembled in the U.S.A. BrassCraft
El fabricante no asume ninguna responsabilidad si la instalación no se hace de acuerdo al instructivo. Diseñado,
Maquinado y Ensamblado en E.U.A. BrassCraft
PSC1106 Range & Dryer Kit Contents:
• 1/2 in. OD x 48 in. Coated Stainless Steel Gas Connector
• Safety+PLUS ® Excess Flow Valve -1/2 in. MIP (tapped 3/8 in. FIP)
• 1/2 in. MIP (tapped 3/8 in. FIP) steel fitting
• 1/2 in. FIP steel fitting
• 3/8 in. MIP steel fitting
• 3mil leak detection solution
Fig. N
• 3mil pipe thread sealant
PSC1107 Professional Range & Furnace Kit Contents:
• 5/8 in. OD x 48 in. Coated Stainless Steel Gas Connector
• Safety+PLUS Excess Flow Valve - 3/4 in. MIP
®
• 3/4 in. MIP (tapped 1/2 in. FIP) steel fitting
• 1/2 in. MIP steel fitting
• 3mil leak detection solution
• 3mil pipe thread sealant
® brand is a trademark of
Brasscraft Mfg. Co.
® brand es una marca registrada de Brasscraft Mfg. Co.
325.04 Rev. 11/19