Subscribe to Our Youtube Channel
Related Manuals for NTC NT59
Summary of Contents for NTC NT59
- Page 1 NTC STAVEBNÍ TECHNIKA spol. s r.o. Jiřinková 120, 552 03 Česká Skalice Czech Republic Tel.: + 420 491 452 184 E- info@ntc-vibro.by mail: www.ntc-vibro.by Представительство в РБ Tel.: + 375 44 737 23 37 e-mail: info@ntc-vibro.by NT59, NT65, NT68, NT-70H...
- Page 2 Prohlašujeme, že zařízení definované níže uvedenými údaji je ve shodě s požadavky níže uvedených NV a směrnic We declare that the trough below mentioned specifications defined equipment complies with requirements of below cited Directives Výrobce (manufacturer): NTC STAVEBNÍ TECHNIKA spol. s r.o. Jiřinková 120, Česká Skalice 552 03 Sídlo firmy (legal address): IČ...
-
Page 3: Safety Instructions
Vibratory tampers Operation manual 1. SAFETY INSTRUCTIONS Vibratory tampers NT are powerful compaction Pay special attention to the safety instructions. machines. These safety instructions must be maintained all Read and understand the operation manual the time, otherwise these may arise a danger to before using starting the machines. - Page 4 Vibratory tampers Operation manual 1. Check the machine thoroughly, repair all failures before starting the engine. If the Jobsite: failures cannot be repaired at the jobsite, do 9. No bystanders are allowed within the not operate the machine. operational range of the machine. Especially 2.
- Page 5 Vibratory tampers Operation manual At the designated types of machinery, vibratory rammer, type NT 59, NT 65 N,NT 68 and NT 70H in accordance with the Act No. 22/1997 Coll. as amended, on technical requirements for products placed stickers symbols safety signs, symbols and informative descriptions of the design and implementation determine the technical norm.
- Page 6 Vibratory tampers Operation manual 2. DESCRIPTION 2.1. Definition of Vibratory Tamper Vibratory tamper is a compaction machine, increases and water contained in the soil is which executes fast repeating blows to the soil pushed out. which is compacted. Vibratory tampers are suitable for compaction During compaction, distances between soil of backfills at digs, compaction of foundations, particles get shorter, specific weight of the soil...
-
Page 7: Operation
Vibratory tampers Operation manual 3. OPERATION 3.1. Starting 1. Turn the fuel tap down. Turn the ignition 4. After the engine gets started, move the switch to position „ON“. choke lever slowly into the basic position. 2. At cold engine: Let the engine to warm up at idle speed for Close the choke. - Page 8 Vibratory tampers Operation manual 6 . Work with the rammer quick stop moving the 5. The tamper is designed to move forward during operation. The forward speed can be throttle to "OFF" increased by pushing the handle down. 3.3. Turning Off The Engine 1.
-
Page 9: Troubleshooting
Vibratory tampers Operation manual wash, let dry and lightly oil Fill. Before and check, whether the fuel does not leak. Drain installing squeeze out excess oil. the fuel tank if necessary. Paper filters blown clean with compressed air NOTE! from the inside liner. Lower the tamper always on the front or If the cartridge is very dirty or damaged, replace right-hand side (with the fuel tank cap up). - Page 10 4.3. Spare Parts All spare parts are available from: NTC STAVEBNÍ TECHNIKA spol. s r.o. Jiřinková 120 552 03 Česká Skalice When ordering the spare parts, please note the type and serial number of the machine, which is stamped on the nameplate of the machine.
-
Page 11: Warranty
Vibratory tampers Operation manual 5. WARRANTY 5.1. Warranty Period The warranty period is 12 months from commissioning of the goods, unless otherwise stated in the sales contract. 5.2. Warranty Terms The supplier warrants the goods as follows: The supplier will repair or replace parts which prove to be defective due to faulty material, manufacturing failure, improper assembly, etc.
Need help?
Do you have a question about the NT59 and is the answer not in the manual?
Questions and answers