Related Manuals for mIoT Captis Power+
Summary of Contents for mIoT Captis Power+
- Page 1 Captis Power+ Installation Guide April 2020 Installation Guide Captis Power+ Rev. 1...
-
Page 2: Table Of Contents
Captis Power+ Installation Guide April 2020 CONTENTS Introduction ........................... 3 Captis Power+ Dimensions ....................3 Captis power+ ........................3 Installation ..........................4 Before You Begin ......................4 What Is In The Captis Box ....................4 Installing the Captis ....................... 4 Mounting the Captis ...................... -
Page 3: Introduction
Captis Power+ Installation Guide April 2020 INTRODUCTION The Captis cellular data logger has been developed to fill measurement requirements across a broad range of applications and locations. The Captis Power+ can be connected to a wide range of sensors through a variety of input types. -
Page 4: Installation
Captis Power+ Installation Guide April 2020 INSTALLATION BEFORE YOU BEGIN Before starting this installation, you will need the following items: • The contents of the Captis box. • The sensor that will be connected to the Captis • An internet-connected device, such as a phone or tablet. -
Page 5: Mounting The Captis
Captis Power+ Installation Guide April 2020 MOUNTING THE CAPTIS Consider the following points when deciding on the mounting location for the Captis: • An external LTE antenna must be used as the Captis Power+ will be installed inside a cabinet. -
Page 6: Terminating The Sensor
Use the diagram below to determine how to wire the connections between the Captis Power+ terminals and the sensor. If you require guidance connecting your specific sensors, please contact mIoT at miot.com.au/contact... -
Page 7: Selecting An External Lte Antenna
Captis Power+ Installation Guide April 2020 SELECTING AN EXTERNAL LTE ANTENNA mIoT recommended LTE antennas include: Taoglas Cyclops WM.90 698 – 960MHz/1719-2690MHz Wide-Band High Efficiency Flexible Inner Steel Core Whip, IP65 3M CFD-200 SMA(M)ST RoHS & Reach Compliant Taoglas Phoenix GSA.8827... -
Page 8: Selecting An External Gps Antenna
Captis Power+ Installation Guide April 2020 SELECTING AN EXTERNAL GPS ANTENNA mIoT recommended GPS antennas include: External Active GPS Antenna TI 1575.42 +/- 1.023 MHz 10 MHz min @S11 <= -10 dB 50 Ohms / R.H.C.P / 2.3 ~ 5.5 V Coaxial Cable: RG174 Length=5M (option) 41mm x 38.5mm x 13mm... -
Page 9: Installing The External Lte Antenna
Captis Power+ Installation Guide April 2020 INSTALLING THE EXTERNAL LTE ANTENNA Connect an LTE antenna to the device’s external LTE SMA connector. Make sure not to over tension the antenna screw. Hand tightening is sufficient, no tools are required for this task. -
Page 10: Checking Network Signal
LTE-M and NBIoT coverage areas. mIoT also recommends that you use a signal strength meter to determine whether your chosen installation location has enough cellular signal for the Captis device to connect and operate effectively. -
Page 11: Troubleshooting
Captis Power+ Installation Guide April 2020 TROUBLESHOOTING Symptom Meaning What to do Device is working as it should, leave Status LED flashing 20 times Device is on/ awake device to collect data Device connected to Device is working as it should, leave... -
Page 12: Safety
Captis Power+ Installation Guide April 2020 SAFETY ELECTROMAGNETIC RADIATION – HUMAN EXPOSURE Warning: This device has a Maximum Permissible Exposure (MPE) radius of 20cm It is the installer’s and end customer’s responsibility to ensure that no person has any body parts within 20cm of the device or antenna while device is transmitting.
Need help?
Do you have a question about the Captis Power+ and is the answer not in the manual?
Questions and answers