Land Pride FDR2572 Operator's Manual page 12

Section 1: Assembly & Set-Up
Section 1: Assembly & Set-Up
Tractor Requirements
Tractor horsepower should be within the range noted
below. Tractors outside the horsepower range must not
be used. The lower 3-Point arms must be stabilized to
prevent side-to-side movement. Most tractors have sway
blocks or adjustable chains for this purpose.
Required Horsepower Range . . . 15 to 60 horsepower
Power Take-Off Requirement . . . . . . . . . . . . 540 rpm
Spline Requirement . . . . . . . . . . . . . . . . . . . 1 3/8" - 6
Hitch Type. . . . . . . . . . . . . . . . . . . . . . . 3- Point Cat. 1
!
WARNING
To avoid serious injury or death:
Lightweight tractors with rear attached implements may need
weights added to the front to maintain steering control.
Consult your tractor Operator's Manual to determine proper
weight requirements and maximum weight limitations.
The tractor MUST be equipped with protective equipment
designed to shield the operator from thrown objects and
from tractor roll over. An enclosed tractor cab with a Roll
Over Protective Structure (ROPS) may qualify. See
tractor's manual for type of protection your tractor has.
Torque Requirements
Refer to "Torque Values Chart" on page 28 to
determine correct torque values for common bolts.
Dealer Preparations
This Grooming Mower has been partially assembled at
the factory. Some assembly and preparation are still
required before the mower is ready for operation and can
be attached to the customer tractor.
Make sure that the intended tractor conforms to the
Tractor Requirements stated above. Also, read and
understand the Operator's Manual for this Grooming
Mower. An understanding of how it works will aid in its'
assembly and setup.
Go through the Pre-Assembly Checklist before
assembling the mower. To speed up your assembly task
and make the job safer, have all needed parts and
equipment readily at hand.
Vented Dipstick Installation
Refer to Figure 1-1:
IMPORTANT: Gearboxes are shipped with solid
plugs in them to prevent oil loss during shipping and
handling. The solid plug on top of the gearbox must
be replaced with a vented dipstick before operating
the implement.
A vented dipstick is shipped loose and packaged with the
Operator's Manual. Remove temporary solid plug from
top of gearbox and replace with vented dipstick. See your
nearest Land Pride dealer if dipstick is missing.
8
FDR2572 & FDR2584 Rear Discharge Grooming Mowers 310-262M
Table of Contents
Assembly Checklist
Make sure miscellaneous assembly tools are on hand: Hammer,
tape measure, hacksaw, assortment of wrenches & sockets,
3/8" drill, drill bits, and spirit level.
Have a forklift or hoist with properly sized chains and safety
stands on hand capable of lifting 2500 lbs.
Have a minimum of two people available during assembly.
Check to see if auxiliary tractor weights are needed.
See Specifications on page 25 for mower weights.
Make sure all major components and loose parts
are shipped with the implement.
Double check to make sure all fasteners & pins are
installed in the correct location. Refer to the Parts
Manual if unsure.
NOTE: All assembled hardware from the factory
has been installed in the correct location.
Remember location of a part or fastener if
removed. Keep parts separated.
Make sure working parts move freely, bolts are
tight & cotter pins are spread.
Make sure all grease fittings are in place and
lubricated.
Make sure all safety labels are correctly located
and legible. Replace if damaged.
Make sure all red reflectors are correctly located
and visible when implement is in transport
position.
Remove
Gas Plug
Check
Installation of Vented Dipstick
Figure 1-1
Referenc
Operator's
Manual
Operator's
Manual &
Parts Manual
Operator's
Manual
Section 4
Page 23
Important
Safety
Information
Page 4
Install
Vented Dip-
Oil Level
Plug
DO NOT
OVERFILL!
30216
11/6/18