Preset Remote Control - Yamaha HTR-5230 Owner's Manual

PRESET REMOTE CONTROL
The provided remote control is factory set to control not only this unit but also most YAMAHA audio components connected
to it
There are eight component selector buttons Press one of these buttons which corresponds to the component you want to
control with the remote control For example, if you press CD on the component selector, the remote control is set to the CD
operation mode, allowing the CD player to be controlled by the buttons on the remote control
AMP(TUNER)
You can perform the basic operations of this
unit Refer to page 7
CD
The code for a YAMAHA CD player is
factory set
DVD/LD
&
DVD MENU
An LD player can be controlled in
the DVDILD mode A DVD player can be
controlled in the DVDILD and DVD
MENU modes The code for a YAMAHA
DVD player is factory set If the remote
control does not operate your YAMAHA
DVD player, you need to set the code
number "0048"
CD
TAPEIMD
The code for a YAMAHA tape deck is
factory set (The code for the YAMAHA
MD recorder can also be set)
7-I---VCR
A VCR can be controlled
TV
A TV can be controlled
CBUSAT
A cable TV or satellite tuner can be
controlled
• The button functions on the remote constrol differ depending on the operation mode Refel to the following pages for details
If you set the remote control with the manufacturers'
codes
listed from page i at the end of this
manual,
you can control other brands of components
Refer to "Setup codes" on page 43 for details
m
Press CD on the
component selector.
6
Adjust the volume.
m
Press~.
Refer to page 40 for the CD
player operation buttons
6
7
Make sure that VOLUME is set to the
"00"
position.
Press AMP(TUNER) on the
AMP
component selector.
<%
• Example: To control YAMAHA CD
player
5
2
3
4
o
m
Turn on the power.
19
Press CD on the input selector.
CD
%
38
PRESET REMOTE CONTROL
The provided remote control is factory set to control not only this unit but also most YAMAHA audio components connected
to it
There are eight component selector buttons Press one of these buttons which corresponds to the component you want to
control with the remote control For example, if you press CD on the component selector, the remote control is set to the CD
operation mode, allowing the CD player to be controlled by the buttons on the remote control
AMP(TUNER)
You can perform the basic operations of this
unit Refer to page 7
CD
The code for a YAMAHA CD player is
factory set
DVD/LD
&
DVD MENU
An LD player can be controlled in
the DVDILD mode A DVD player can be
controlled in the DVDILD and DVD
MENU modes The code for a YAMAHA
DVD player is factory set If the remote
control does not operate your YAMAHA
DVD player, you need to set the code
number "0048"
CD
TAPEIMD
The code for a YAMAHA tape deck is
factory set (The code for the YAMAHA
MD recorder can also be set)
7-I---VCR
A VCR can be controlled
TV
A TV can be controlled
CBUSAT
A cable TV or satellite tuner can be
controlled
• The button functions on the remote constrol differ depending on the operation mode Refel to the following pages for details
If you set the remote control with the manufacturers'
codes
listed from page i at the end of this
manual,
you can control other brands of components
Refer to "Setup codes" on page 43 for details
m
Press CD on the
component selector.
6
Adjust the volume.
m
Press~.
Refer to page 40 for the CD
player operation buttons
6
7
Make sure that VOLUME is set to the
"00"
position.
Press AMP(TUNER) on the
AMP
component selector.
<%
• Example: To control YAMAHA CD
player
5
2
3
4
o
m
Turn on the power.
19
Press CD on the input selector.
CD
%
38