Table of Contents
Advertisement
Safety Guidelines
Personal Protection
Be sure to use all personal protective
equipment, such as sturdy work boots,
preferably with steel toes, gloves, and hard hat, if necessary,
to ensure your own safety. To prevent possible damage to
your hearing, always wear ear protection, such as earmuffs or
earplugs, when working around power tools.
Cutting Hazard
The installation of the Swan product may require using
power tools. Keep hands away from the cutting edge
of any tool used in the installation of our product. Placing
fingers in or around the cutting blades could result in serious
personal injury.
WARNING
WARNING: Indicates a potentially hazardous situation which,
if not avoided, could result in serious injury or death.
Eye Protection
Be sure to use all personal protective equipment to
ensure your own safety. To avoid eye injury, always
wear protective glasses with side shields when using power
tools. Also, make sure no one else can be injured by flying
particles when using power tools.
Fire Hazard
Personal injury or death can result from a
fire caused by flammable liquids or
silicone. Cleaners or solvents can be highly explosive, resulting
in personal injury or even death, when not used properly. Clean
up any flammable substance immediately. Sparks or open
flames can cause flammable substances to ignite. DO NOT
smoke while working on or near any flammable substance.
Solvents Hazard
Follow all manufacturer's safety instructions for silicone
and denatured alcohol. Alcohol vapors are both
flammable and hazardous to breathe. Silicone vapors may
irritate eyes and nose. Personal injury can result from
improperly handling or use of products such as denatured
alcohol. Always follow the manufacturer's recommendations for
the safe use of these products. Ventilate any work area before
beginning to apply silicone, cleaning agents, or solvents.
Fumes Hazard
The fumes from the silicone and solvents used
by the installer can be harmful if used in an
unventilated room. Always work in a well-ventilated area.
Power Tool Hazard
To prevent personal injury or possible death,
always follow the electrical safety
recommendations of the power tool's manufacturer. Do not
use power tools in an unsafe manner. Power tools should only
be connected to a circuit protected by a ground-fault circuit
interrupter (GFI).
Shock Hazard
Never use electric power tools around water,
condensation, or other liquids. Electric shock can
cause severe burns, significant injuries, and even death. If an
extension cord is required, always use an OSHA approved
extension cord. Power cords should only be connected to a
circuit protected by a ground-fault circuit interrupter (GFI).
800-325-7008
Electrical Shock Hazard
Contacting live electrical wiring with power tools
or hand tools can cause serious injury or death.
Make sure all related circuit breakers are turned OFF. Test for
live circuits or wiring inside any wall where installation of the
Swan product requires cutting into a wall.
Electrocution Hazard
Water and other liquids conduct electric current
and can create a short circuit, resulting in injury
or death. Keep all liquids away from electrical cords and
power tools. DO NOT create a short circuit between a source
of electricity and a liquid by being in contact with both
simultaneously.
General Information
A laundry tub or utility sink can be a useful addition to any home
to soak dirty clothes, wash the dog, or clean large, odd-shaped
household goods. Our laundry tubs are made from Veritek,
which makes them easy to install and maintain. Our Veritek
material has no surface coating to chip or crack and will not
mold or mildew. The laundry tubs can also be secured to the
wall or the floor as a precaution to prevent unwanted tipping.
The installation process is straightforward and most
homeowners can easily complete the task. The hardest part of
the job, if necessary, may be installing the water lines and
drain pipe. Always check local building codes to verify that
you, the homeowner, can install the plumbing yourself.
A laundry tub is an easy project to install and requires very few
special tools. Followed carefully, these installation instructions
will result in an easy, trouble-free installation of your Swan
Corporation product. Any deviations, additions, and/or deletions
from the prescribed installation, without prior written approval of
our Customer Relations Department, will void the warranty
covering this product. Not following the directions could also
result in personal injuries, water damage, and other damage to
floors, pipes, walls, and other portions of your building or home.
• Read all instructions completely before beginning
installation.
• Check all local plumbing codes.
• Be sure to shut off the water at the source before
starting installation.
Contents (Floor Mount Units)
Laundry Tub
Four Metal Angular Legs
Four Metal Angular Legs or Four Plastic Angular Legs
Leveling Brackets (Qty 4)
Flat Head Screws (Qty 4)
Nuts (Qty 4)
3
General Information
LT-031
The Swan Corporation – Swanstone
Advertisement
Table of Contents
