Table of Contents
Advertisement
Quick Links
LISTED
3765 Champion Boulevard
Winston-Salem, NC 27105
(336) 661-1556 Fax: (336) 661-1660
Toll-free: 1 (800) 858-4477
Installation Manual
2674 N. Service Road, Jordan Station
Ontario, Canada L0R 1S0
(905) 562-4195 Fax: (905) 562-4618
Toll-free: 1( 800) 263-5798
DH6000T-VHR
Hot water sanitizing machine
w/fresh water rinse and built-in
stainless steel electric booster
Ventless Heat Recovery
Issue Date: 10.30.18
Manual P/N
116081 rev. A
For machines beginning with S/N D1806487 and above
Printed in the USA
Advertisement
Table of Contents
Related Manuals for ALI Champion DH6000T-VHR
Summary of Contents for ALI Champion DH6000T-VHR
- Page 1 Installation Manual DH6000T-VHR Hot water sanitizing machine w/fresh water rinse and built-in stainless steel electric booster Ventless Heat Recovery Issue Date: 10.30.18 Manual P/N LISTED 116081 rev. A For machines beginning with S/N D1806487 and above 3765 Champion Boulevard 2674 N. Service Road, Jordan Station Printed in the USA Winston-Salem, NC 27105 Ontario, Canada L0R 1S0...
- Page 2 National Service Department In Canada: In the USA: Toll-free: (800) 263-5798 Toll-free: (800) 858-4477 Tel: (905) 562-4195 Tel: (336) 661-1556 Fax: (905) 562-4618 Fax: (336) 661-1660 email: service@moyerdiebellimited.com email: service@championindustries.com ATTENTION The model no., serial no., voltage, Hz and phase are needed to identify your machine.
- Page 3 Product Registration Two ways to REGISTER YOUR PRODUCT and ACTIVATE YOUR WARRANTY. 4:34 PM • Use your mobile device to visit our website at www. championindustries.com and register your product. • Complete the fax form on the next page and fax to 1-800 661-1660.
- Page 4 Product Registration PRODUCT REGISTRATION BY FAX COMPLETE THIS FORM AND FAX TO: (336) 661-1660 in the USA 1-(800) 204-0109 in Canada PRODUCT REGISTRATION CARD Model Serial # Date of Installation: Company Name: Address: (Street) State/Province Zip/Postal Code Telephone #: ( Contact: Installation Company: Address:...
- Page 5 Revision History Revision History Specifications are subject to change based on continual product improvement. Equipment owners may request a revised manual, at no charge, by calling 1 (800) 858-4477 in the USA or 1(800) 263-5798 in Canada. Revision Revised Serial Number Revision Date Pages...
-
Page 6: Limited Warranty
Limited Warranty LIMITED WARRANTY Champion Industries (herein referred to as “The Company”), 3765 Champion Blvd., Winston-Salem, North Carolina 27105, and 2674 N. Service Road, Jordan Station, Ontario, Canada, L0R 1S0, warrants machines, and parts, as set out below. Warranty of Machines: The Company warrants all new machines of its manufacture bearing the name “Champion and installed within the United States and Canada to be free from defects in material and workmanship for a period of one (1) year after the date of installation or fifteen (15) months after the date of shipment by The Company, whichever occurs first. -
Page 7: Table Of Contents
Table of Contents Table of Contents Revision History ..........................i Limited Warranty ......................... ii Installation Codes and Safety Symbols ..................iv Installation ....................1 Receiving and Placement ................1 Dish Table Connections................... 2 Corner Operation .................... 3 Water Connection ................... 5 Drain Connection .................... -
Page 8: Installation Codes And Safety Symbols
Installation Codes and Safety Symbols Installation Codes The installation of the dishwasher must comply with all local electrical, plumbing, health and safety codes or in the absence of local codes, installed in accordance with the applicable requirements in the National Electrical Code, NFPA 70, Canadian Electrical Code (CEC), Part 1, CSA C22.1;... -
Page 9: Receiving And Placement
Receiving and Placement - Installation Receiving Inspect the outside of the shipping carton for signs of damage and report any damage immediately to a supervisor. Remove the carton, inspect the dishwasher, and check the inside of the machine for accessories and installation parts. Register your machine by fax or online as soon as possible. -
Page 10: Dish Table Connections
Installation Dish Table Connections CAUTION: Do not attach the dish tables until the dishwasher is set in its permanent location. Dish table flange Drill holes, apply sealant, & fasten flange to wash tank Side panel Inner wall of wash tank 1/2”... -
Page 11: Corner Operation
Installation Corner Operation - Corner Splash Shield Machines are shipped from the factory for straight through operation. To convert to for corner operation: The control panel must be accessible from the front as shown in Fig. 4. Install the optional splash shield, if equipped, see Fig. 5. Detailed instructions can be found in Appendix A at the rear of this manual. - Page 12 Installation Corner Operation - Track Conversion Follow the steps below to convert the track assembly for corner operation: Pull the track assembly straight up out of the machine. Rotate the track 180° and reinstall. Remove the guide attached to the track assembly, save the hardware. Reposition the guide on the right-hand side of the track assembly and secure with the existing fasteners.
-
Page 13: Water Connection
Installation Water Connection COLD MINIMUM 3/4" NPT COLD WATER SUPPLY WATER CAUTION: To prevent damage to the dishwasher supply valves, the installing plumber must thoroughly flush debris from the water supply line before connecting it to the dishwasher. Damage caused by improper installation is not covered by the limited warranty. -
Page 14: Drain Connection
Installation Drain Connection DRAIN GRAVITY DRAIN, 1-1/2" NPT CONNECTION CAUTION: The dishwasher drain connection must comply with all local plumbing, health and safety codes. Damage caused by improper installation is not covered by the limited warranty AUTOMATIC ELECTRIC DRAIN VALVE MAXIMUM FLOW RATE: 15 USGPM/1.5 IMP. -
Page 15: Drain Water Tempering Valve
Installation Drain Water Tempering Kit A field installation kit is included with the machine to reduce the temperature of water entering the building drain MECHANICAL WATER VALVE COLD WATER MINIMUM 1/2" NPT COLD WATER SUPPLY LINE USES BUILDING FLOWING PRESSURE Fig. -
Page 16: Electrical Connection
Installation Electrical Connection - Single and Three Phase The installation of the dishwasher must comply with all local electrical, plumbing, health, and safety codes or in the absence of local codes, installed in accordance with the applicable requirements in the National Electrical Code, NFPA 70, Canadian Electrical Code (CEC), Part 1, CSA C22.1;... - Page 17 Installation Electrical Connection - Single and Three Phase WARNING: There may be more than one power source connected to the machine. Make sure all power sources are disconnected, locked and tagged out before working on the machine. 3 Phase Power Connection 1 Phase Power Connection 208-240/480V/60/3 208-240V/60/1...
-
Page 18: Chemical Connections
Installation Detergent Dispenser Connection USE A NON-CHLORINATED COMMERCIAL GRADE DETERGENT WASH TANK CAPACITY: 10 US GAL/8.33 IMP. GAL/ 38 L TWO 7/8" DIAMETER HOLES AT LOWER RIGHT REAR CORNER OF TANK. - TOP HOLE IS DETERGENT INJECTION - BOTTOM HOLE IS DETERGENT PROBE. 120VAC FUSE BLOCK-1.5 AMP- MAX LOAD DETERGENT SIGNAL CONNECTION. -
Page 19: Rinse-Aid Dispenser Connection
Installation Rinse-Aid Dispenser Connection STD. RINSE/RACK: .85 US GAL/.7IMP. GAL/3.2.L R /A POT,PAN,RINSE/RACK 1.18 US GAL/.98IMP.GAL/ 4.5L 1/8" NPT PIPE PLUG AT THE REAR OF THE MACHINE NEAR THE VACUUM BREAKER FOR RINSE-AID INJECTION. 120VAC FUSE BLOCK-1.5 AMP- MAX LOAD RINSE-AID SIGNAL CONNECTION. - Page 20 Blank Page This Page Intentionally Left Blank...
-
Page 21: Appendix A: Dh6000T Corner Splash Shield Kit, P/N 901104
APPENDIX A : Installing DH6000T Corner Splash Shield Kit P/N 901114 INSTALLING DH6000T, CORNER SPLASH SHIELD KIT, P/N 901114 CAUTION: Turn off dishwasher power. The machine will drain automatically. KIT PARTS: (1) SHIELD, CORNER SPLASH, P/N 337955, COMPOUND SEALING, P/N 104889, (2) SCREWS, 10-32 X 1/2"... - Page 22 APPENDIX A : Installing DH6000T Corner Splash Shield Kit P/N 901114 Remove the (4) bolts, locks, and washers securing the right-hand door guide cover. Save the fasteners and discard the cover (Fig. 3). Guide Cover Fig. 3 Install the splash shield between the door guide and the front corner post (Fig. 4). The left side of the splash shield covers the door guide.
- Page 23 APPENDIX A : Installing DH6000T Corner Splash Shield Kit P/N 901114 Apply a small bead of sealing compound to the (4) fasteners saved in step 4. Secure the guide cover end of the splash shield to the machine (Fig. 5). Sealing Compound Fig.
- Page 24 APPENDIX A : Installing DH6000T Corner Splash Shield Kit P/N 901114 Using the splash shield as a template, mark and drill two holes in the corner post. Secure the shield to the post using the 10-32 screws, nuts and washers provided in the kit. Fig.
-
Page 25: Appendix B: Dh6000T-Vhr 3Ph To 1Ph Electrical Conversion Instructions
APPENDIX B : DH6000T-VHR 3PH to 1PH Electrical Conversion Instructions CONVERTING DH6000T-VHR FROM 3 PHASE TO 1 PHASE OPERATION for 208-240V only. WARNING: Prevent electrocution when working on energized circuits. Disconnect power at main breaker or service disconnect switch, then lock out and tag the circuit. - Page 26 Blank Page This Page Intentionally Left Blank...
Need help?
Do you have a question about the Champion DH6000T-VHR and is the answer not in the manual?
Questions and answers