Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Husqvarna 330i
Summary of Contents for Husqvarna 330i
- Page 1 ® 330i, 535i XP Operator's manual 2-37...
-
Page 2: Table Of Contents
Intended use Product description This product is intended for sawing in wood. Husqvarna 330i, 535i XP are chainsaw models with an electric motor. Note: National regulations can set limit to the operation Work is constantly in progress to increase your safety of the product. - Page 3 Husqvarna HXX Recommended cutting equipment in this 24. Charging LED example: Bar length XX in (XX mm), max. 25. Warning indicator nose radius X Teeth, chain type Husqvarna XX mm/XX 26. Power cord HXX. 27. Combination wrench 28. Battery charger Measured maximum kickback value without 29.
-
Page 4: Safety
California Proposition 65 Safety Safety definitions • Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and The definitions below give the level of severity for each refrigerators. There is an increased risk of electric signal word. shock if your body is earthed or grounded. - Page 5 • Dress properly. Do not wear loose clothing or • Use power tools only with specifically designated jewellery. Keep your hair, clothing and gloves away battery packs. Use of any other battery packs may from moving parts. Loose clothes, jewellery or long create a risk of injury and fire.
- Page 6 Do not attempt any task that you feel unsure of! unexpected situations. • Turn to your servicing dealer or Husqvarna if you • Only use replacement bars and chains specified by have questions about the operation of the product.
- Page 7 questions about kickback on page 15 for are on a ladder or in a tree. Do not use the product if instructions. you are not on stable ground. • Do not use a product, battery or battery charger that is defective. •...
- Page 8 trees, causes more vibration than cutting softwoods, such as conifers. Personal protective equipment • Overexposure to vibration can lead to circulatory WARNING: Read the warning instructions damage or nerve damage in persons who have that follow before you use the product. decreased circulation.
- Page 9 • If the safety devices are defective, speak to your mechanism that stops the drive sprocket. Husqvarna servicing dealer. Keypad The warning indicator flashes if the chain brake is engaged or if there is a risk of overload. The overload protection temporarily stops the product and you can not use the product until the temperature restores.
- Page 10 decreases the risk that you or a person near you In the felling position you cannot engage the chain brake touches the saw chain. manually. The chain brake can in this position only be engaged by the inertia release mechanism. Power trigger lockout The power trigger lockout prevents accidental operation of the power trigger.
- Page 11 • Use an approved grounded mains socket that is not damaged. • Do not use other battery chargers than the one supplied for your product. Only use Husqvarna QC chargers when you charge Husqvarna replacement Battery safety batteries BLi. •...
-
Page 12: Assembly
Assembly To assemble the guide bar and saw 1. Disengage the chain brake. chain (330i) WARNING: Always remove the battery before you assemble or do maintenance on the product. 958 - 010 - 24.04.2020... - Page 13 2. Loosen the knob and remove the drive sprocket 1. Disengage the chain brake. cover (chain brake) and the transportation ring (A). 2. Loosen the bar nut and remove the drive sprocket cover and the transportation ring (A). 3. Put the guide bar on top of the bar bolt. Steer the guide bar to its most rear position.
-
Page 14: Operation
• Use Husqvarna chain oil for maximum saw chain life To do a function check before you use and to prevent negative effects on the environment. If Husqvarna chain oil is not available, we the product recommend you to use a standard chain oil. - Page 15 1. Make sure that the battery is dry. and with large force, which throws the product in the direction of the operator. 2. Put the battery in the battery charger. Kickback always occurs in the cutting plane of the guide bar.
- Page 16 possible that the chain brake does not stop the saw 4. Press on the lower part of the battery until you hear chain before it touches you. There are also some a click sound. positions in which your hand can not touch the front CAUTION: If the battery does not move hand guard to engage the chain brake.
- Page 17 To stop the product • To cut on the push stroke is when you cut with the top of the guide bar. The saw chain pushes the 1. Press and hold the start/stop button on the keypad product in the direction of the operator. until the green LED light comes off.
- Page 18 1. Cut on the push stroke approximately ⅓ through the WARNING: Cut pieces in the work area trunk. increase the risk of kickback and that 2. Cut through the trunk on the pull stroke until the two you cannot keep your balance. kerfs touch.
- Page 19 chain and prevent safe operation of the b) Cut on the push stroke. product. Note: If it is necessary, cut the limbs piece by piece. Cut the smaller branches (A) and (B) before you cut the limb near the trunk (C). 3.
- Page 20 To keep a safe distance 6. Do not let the tree fall onto a different standing tree. It is dangerous to remove a caught tree and there is 1. Make sure that persons around you keep a safe To free a trapped tree a high accident risk.
- Page 21 To fell a tree Husqvarna recommends you to make the directional cuts and then use the safe corner method when you fell 2. Make sure that the directional cut line is perfectly a tree.
- Page 22 a) Make a bore cut straight into the trunk to 4. Cut off the corner to make the tree fall. complete the felling hinge width. Note: If the tree does not fall, hit the wedge until it does. 5. When the tree starts to fall, use the path of retreat to move away from the tree.
-
Page 23: Maintenance
3. Examine which is the safest procedure to release the WARNING: Be very careful when you tension. cut a tree that is in tension. There is a risk that the tree moves quickly before or Note: In some situations the only safe procedure is after you cut it. - Page 24 Maintenance Before Weekly Monthly Make sure that the cutter and cutter guard have no cracks and that they are not damaged. Replace the cutter or cutter guard if they have cracks or if they have been exposed to impact. Make sure that the guide bar and saw chain have sufficient oil. Do a check of the saw chain.
- Page 25 2. Wrap your fingers and thumbs around the handles 3. Make sure that the power trigger is locked at the idle and hold the product tight. position when the power trigger lockout is released. 4. Start the product and apply full power. 5.
- Page 26 Replace a worn or damaged guide bar or saw chain with the guide bar and saw chain combination recommended by Husqvarna. This is necessary to keep the safety Accessories on page functions of the product. Refer to 34 , for a list of replacement bar and chain combinations that we recommend.
- Page 27 Round file diameter. It is not easy to sharpen a saw chain correctly without General information about how to sharpen the the correct equipment. Use Husqvarna file gauge. This cutters will help you to keep maximum cutting performance and the kickback risk at a minimum.
- Page 28 1. Use a flat file and a depth gauge tool to adjust the 3. Move the file from the inner side of the cutting teeth depth gauge setting. Only use Husqvarna depth and out. Decrease the pressure on the pull stroke.
- Page 29 To adjust the tension of the saw chain (330i) 5. Turn the knob clockwise to tighten the bar knob. 1. Fold the knob out until it opens. 6. Fold down the knob to lock the tension. 2. Turn the knob counterclockwise to loosen the drive sprocket cover.
- Page 30 5. Make sure that you can pull the saw chain around b) Do a check of the groove in the edge of the guide freely by hand and that it does not hang from the bar to make sure that it is clean. Clean if guide bar.
-
Page 31: Troubleshooting
To examine the cutting equipment 3. Clean the groove in the guide bar. 1. Make sure that there are no cracks in rivets and links and that no rivets are loose. Replace if it is necessary. 4. Examine the groove in the guide bar for wear. Replace the guide bar if it is necessary. -
Page 32: Transportation, Storage And Disposal
LED display Possible faults Possible action Warning indicator flashing. Chain brake engaged. Pull back the front hand guard to re- lease the chain brake. Temperature deviation. Allow the product to cool down. Overload. Cutting attachment jam- The cutting attachment is jammed. med. -
Page 33: Technical Data
• Use the transportation guard on the product to prevent injuries or damage on the product during transportation and storage. Technical data Technical data 330i 535i XP Motor Type BLDC (brushless) 36V BLDC (brushless) 36V Features... -
Page 34: Accessories
Association Z62.1-11 (Chain saws) and Z62.3-11 (Chain Saw Kickback). Following is a list of recommended cutting equipment for Husqvarna 330i and 535i XP. This model equipped with Furthermore the saw chain Husqvarna H38 is evaluated either of the listed guide bar and saw chain... - Page 35 US: 596 28 US: 596 28 51-04 47-01 11/64 in / 0.025 in/ 75° 30° 0° 4.5 mm 0.65 mm CA: 505 69 CA: 579 55 81-03 88-01 5/32 in / 4.0 0.025 in/ US: 595 00 US: 592 00 60°...
-
Page 36: Warranty
Warranty AMERICAN STANDARD SAFETY operation. A chain saw is intended for two- handed use. PRECAUTIONS Do not operate a chain saw when you are fatigued. SAFETY PRECAUTIONS FOR CHAIN SAW USERS Use safety footwear; snug-fitting clothing, protective (ANSI B175.1-2012 Annex C) gloves, and eye, hearing and head protection devices. - Page 37 Note: This Annex is intended primarily for the consumer or occasional user. 958 - 010 - 24.04.2020...
- Page 38 958 - 010 - 24.04.2020...
- Page 39 958 - 010 - 24.04.2020...
- Page 40 Original instructions 1140988-95 2020-04-29...