CONTENTS INTRODUCTION ............................. 2 WARRANTY AND SERVICE ........................2 SYMBOLS ............................... 2 SAFETY RULES AND WARNINGS ......................3 INSTALLATION ............................3 Installation of the Systyem ........................3 Installation of Gas Water Heater ......................3 COMISSIONING ............................3 OPERATION AND MAINTENANCE......................4 PRODUCT ...............................
INTRODUCTION First of all, we would like to thank you for choosing an E.C.A. gas water heater. E.C.A. Phoenix gas water heaters are designed to accomodate the domestic hot water needs in a safe and comfortable way. Information about installation and operation of Phoenix gas water heaters are provided in this manual. Technical specifications, choosing the right place to install, water, gas, flue and electrical connections, maintenence information and a list of possible errors are given in detail.
SAFETY RULES AND WARNINGS If there is a natural gas smell; Shut off the gas valve of the appliance and all of your gas burning appliance Shut off and put out your oven, stove, cooker etc. Do not light matches, lighters etc, put out your cigarettes. ...
OPERATION AND MAINTENANCE • Please be wary of the warnings in the installation and user manual. That way, any danger caused by false operation could be prevented. • For the longevity and high performance of your appliance, maintenance once a year is advised. Maintenance is under the scope of appliance’s warranty and must be done by the authorized technical services.
Product Notation Notation Description Phoenix PH HM 11 E.C.A. Phoenix Gas Water Heater Table 1 Technical Data PH11HM Unit Category l2H, l2E Gas Type Natural Gas Power Min. Heat. Power (Pmin) 7,37 Maks Heat. Power (Pmaks) 18,94 Min. Load (Qmin)
INSTALLATION AND CONNECTIONS Selecting the Suitable Place for Installation The appliance must be installed in accordance with gas safety regulations and relevant standards. Additionally, the clearances around the boiler should be as shown in fig. 4 in order to make service, maintenance and usage easier.
Hanging the Appliance to the Wall E.C.A. Phoenix gas water heater must be hung to a brick wall with the supplied hanging bracket. Hanging bracket Figure 5- Hanging bracket For installation: Take measurement from the back side of the boiler to make sure that the holes are in line and horizontal. ...
Horizontal Flue Connections Air/flue kit consists of the following parts: Apart from the water heater package, a standard concentric air/flue kit is given with a cardboard box. a) 90⁰ Concentric elbow with flange (φ60/100mm), Flat sealing ring Sealing ring, Viton (φ60mm) Sealing ring, Silicone (φ100mm) b) Concentric terminal, L=860mm, (φ60/100mm) Inner and outer flanges, 2 pieces (φ100mm)
Figure 11 - Vertical Flue Assembly Type Chimney Lenght Setting Definitions: Depending on the flue lenght configuration there is a parameter defined to control fan speed to have the best efficiency and emmission values of combustun. As the installation completed, this parameter must be set by an authorized service technician at start-up.
Gas and Water Connections Water & gas connections distance between the pipes’ connections are shown in fig. 12. Figure 12 A suitable valve should be mounted on the gas inlet and the water circuits. In addition, a water filter should be mounted on cold water (1/2”) inlet.
CONTROL PANEL The control panel shown in fig. 13 consists of the following parts as detailed below. Single Button Black LCD Screen (Rotate&Push) Figure 13 - Control Panel ON/OFF & Temperature Setting Knob Functions a) The appliance is turned ON/OFF using the knob by pushing it. b) Set the water temperature between 35 °C and 60 °C by rotating.
On Mode: Pushing the button screen will be activated automatically. In case an error, AL and the referance fault code apears on the screen alternately. Reseting the fault, you must keep pushing the button 3 seconds, when RESET letter starts blinking you can leave pushing the button. If the fault does not dissappear after reset you can read troubleshooting or you can call an authorized service technician.
TROUBLESHOOTING ERROR CODE POSSIBLE CAUSE SOLUTION Check the plug. ON/OFF boiler is not started. Electrical supply is not provided. If it is OK, call an authorized service. AL01 Cable connection fault. Call an authorized service Flame loss fault AL02 Overheating Overheating cable is cut off Call an authorized service fault...
Page 17
Product Fiches and Package Label Calculations 1. PRODUCT FICHES Product fıche for combination boilers as required by EU regulations No 812/2013 Units MODEL PHOENIX PH HM 11 LT/MIN WATER HEATER Supplier's name or trademark E.C.A. PHOENIX PH HM Supplier's model identifıer...
Page 20
PRODUCTION EMAS MAKINA SANAYI A.S. Organize Sanayi Bölgesi 3. Kısım Mustafa Kemal Bulvarı No: 13 45030 MANISA Tel. : +90 236 213 00 21 Fax : +90 236 213 08 59 email: emas@emas.com.tr www.emas.com.tr SALES EMAS MAKINA SANAYI A.S. Esentepe Mah. Kasap Sok. No:15/1 34394 Sisli / ISTANBUL Tel.
Need help?
Do you have a question about the PHOENIX PH HM 11 and is the answer not in the manual?
Questions and answers