Page 1
A.C.N. 098 264 316 A.B.N. 42 098 264 316 Quality Endorsed BROBO GROUP (AUST) PTY. LTD. Company ISO 9001 Lic. 10292 8 Fowler Rd, Dandenong, 3175 SAI GLOBAL Victoria, AUSTRALIA. ✆ ✉ 61 3 9794 8751 info@brobo.com.au Fax: 61 3 9794 8792 www.brobo.com.au...
Page 2
4.3.2 3M Drill Bench Mount CHAPTER 5: Maintenance & Selection of Consumables Role of the Operator Maintenance Requirements General Maintenance of Functioning Components CHAPTER 6: Troubleshoot General Troubleshooting APPENDIX Hazard/Risk Assessment Brobo Group Warranty iii. Workplace Health & Safety Policy...
Upon receiving the Brobo Group 3M Drill, the machine should be standing upright & positioned centrally on top of a wooden pallet. While the machine is situated on the pallet, position the forklift arms under the pallet between the runners, keeping in mind that the machine is head heavy &...
Page 5
1.2. Parts Checklist Along with the drill unit, check that the following accessories, packed "loose", are included as follows: STANDARD ACCESSORIES 1) 1 Operation Manual 1.3. Minimum Requirements For the machine to function correctly, the room in which the drill unit is to be installed must be in the vicinity of, & satisfy the following conditions: ...
1.5. Connection to Power Source Before connecting the machine to the power supply, check that the socket is not connected in series with other machines. This condition is critical for the ideal operation of the drill unit. Single & Three Phase a) Single phase machines are provided with three pins, 15 amps rated plugs &...
Page 7
6) If all of the above procedures have been carried out correctly, the drill should now be operational Brobo Group 3M Drill is now ready for use. Chapter 3 provides a detailed description of the various features of the drill & its operating cycles...
CHAPTER 2 - Safety & Accident Prevention Brobo Group 3M Drill has been designed & manufactured in accordance with Australian Standards. It is HIGHLY RECOMMENDED that the instructions & warnings contained in this chapter be carefully followed for correct usage of the machine.
2.1.2. Power Supply The 415/240V power supply requirements for this machine are of a high level & unauthorised interference and or inadequate maintenance could result in a situation that could put the operator at risk. A qualified electrical engineer should always be assigned to maintain & repair the system. 2.2.
Never move the drill while the machine is operating. Always keep the workplace are as clean as possible. Remove equipment, tools or any other objects from the drilling zone. Support the workpiece to prevent it falling or jamming during the drilling cycle. Brobo Group brobo.com.au...
This could damage the drill, the specimen or be a cause for potential injury to the operator. Always turn off the machine before carrying out any repair work. Consult the Brobo Group Engineering Department in the country in which the machine was initially purchased. 2.4. Machine Safety Devices This product &...
Figure 6. Drill Head 3.1.2. Safety Eye Shields As the name suggests, the safety eye shield should be lowered into position prior to drilling to prevent any swarf dislodging in the direction of the user. Figure 7. Safety Eye Shields Brobo Group brobo.com.au...
3.1.3. Depth Adjustment Situated beneath the 3-pronged handle boss is the depth adjustment gauge. Using the gauge & the scale indicator shown on the left-hand side of the drill, the operator can manually set the desired depth for a drill hole & lock its position.
3.2. Preparation for Operation The following procedure is recommended for the correct drilling using the Brobo Group 3M Drill WARNING – SAFETY GEAR Protective clothing, safety glasses and gloves should always be worn while loading parts, operating the machine, or undertaking any maintenance work on the machine.
Please find below for most commonly replaced spare parts. These listed parts draw reference to components found predominantly on the rack lift assembly & drill column support. Should you require a spare part that you are not familiar with, or not shown in Chapter 4, please contact Brobo Group Engineering department. PART NUMBER...
Page 16
DRILL HEAD DRILL RACKLIFT TABLE DRILL COLUMN SUPPORT DRILL FLOOR BASE 3M DRILL TITLE: 3M DRILL ASSEMBLY BROBO GROUP ISSUED DATE 03.12.2018 DRAWN BY ANH Address : 8 Fowler Rd, Dandenong VIC 3175 https://brobo.com.au/ SCALE:NTS SHEET 1 OF 1...
(1-12) 1041170 PULLEY INTERMEDIATE DRIVE ASSEMBLY (24-30) 2111170 SPINDLE & EXTENSION ASSEMBLY ISSUED DATE 05.12.2018 2121180 DRILL TOGGLE ASSEMBLY DRAWN BY ANH BROBO GROUP 2131020 STANDARD SWITCH ASSEMBLY 3M DRILL HEAD 1051190 BELT GUARD ASSEMBLY TITLE: 1031570 CHUCK GUARD 1031570...
Page 18
Dial Pressure Cap 1044190 Intermediate Drive Block 1035070 External Clip 1034230 Drill Plunger 1044210 Locking Handle ISSUED DATE 05.12.2018 DRAWN BY ANH BROBO GROUP Intermediate Drive 1044200 Spindle 1045810 External Circlip 15mm 3M DRILL HEAD TITLE: 1045290 Intermediate Drive Pulley ASSEMBLY...
Page 19
8115090 Brobo Logo FCSM4x10 Flat Socket Head Cap Screw M4x10 8726100 Button Head Socket Screw M6x16 1105050 Catch Plate 1015240 Latch 8715930 Rivet 1034340 Piano Hinge 1035360 Drill Belt Guard Cover 1034250 Rubber Buffer 1604100 Plate Clamp 1035370 Drill Belt Guard Bottom ITEM NO.
Page 20
PART NO. 2122050 NO. PART NUMBER DESCRIPTION QTY. TOGGLE ASSEMBLY 3M DRILL TOGGLE PART NO. TITLE: 2121180 ISSUED DATE 13.12.2018 BROBO GROUP Address : 8 Fowler Rd, Dandenong VIC 3175 DRAWN BY ANH ASSEMBLY SCALE:1:5 https://brobo.com.au/ SHEET 1 OF 1...
Page 21
Drill Switch Aseembly 1Ph TO MOTOR PLATE PART NO. 2122070 3M STANDARD PART NO. TITLE: 2131020 ISSUED DATE 13.12.2018 BROBO GROUP Address : 8 Fowler Rd, Dandenong VIC 3175 DRAWN BY ANH SWITCH ASSEMBLY SCALE:1:5 https://brobo.com.au/ SHEET 1 OF 1...
Page 22
ITEM PART DESCRIPTION QTY. PART NO. 2111300 NUMBER Range 51-70mm Worm Gear Clamp, Range 51- 1035870 Suit 2M/3M Series 70mm BandWidth 12mm 1033190 Link Arm U Shape 1033250 Link 2 (Both End Serated) 1033260 Link 3 (One End Serated) 1033270...
Page 23
Drill Floor Base ITEM PART NUMBER DESCRIPTION QTY. DRILL FLOOR BASE TITLE: 3M DRILL - FLOOR BROBO GROUP ISSUED DATE 13.12.2018 COLUMN ASSEMBLY DRAWN BY ANH Address : 8 Fowler Rd, Dandenong VIC 3175 https://brobo.com.au/ SCALE:NTS SHEET 1 OF 1...
Page 24
NOTE MINIMUM 600MM ALL ANCHOR HOLE AROUND SAFE SPACE FOR LOCATION OPERATING ZONE TITLE: 3M DRILL BROBO GROUP ISSUED DATE 07.12.2018 FLOOR MOUNT DRAWN BY ANH Address : 8 Fowler Rd, Dandenong VIC 3175 https://brobo.com.au/ SCALE:NTS SHEET 1 OF 1...
Page 25
DRILL TABLE RACKLIFT DRILL COLUMN SUPPORT COLUMN SUPPORT ASSEMBLY BENCH DRILL TABLE SIZE TITLE: 3M DRILL BROBO GROUP ISSUED DATE 13.12.2018 BENCH MOUNT DRAWN BY ANH Address : 8 Fowler Rd, Dandenong VIC 3175 https://brobo.com.au/ SCALE:NTS SHEET 1 OF 1...
Page 30
THREE PHASE ONE PHASE OPTION COMPONENT / SCHEMATIC / WIRING DIAGRAMS FOR CONNECTION FOR 1 PHASE OR 3 PHASE CIRCUIT ISOLATOR...
Page 31
REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY 1041650 TOLERANCES: MEANS IN PART OR IN WHOLE WITHOUT THE WRITTEN ASSEMBLY MATERIAL: Address : 8 Fowler Rd, Dandenong VIC 3175 LINEAR: PERMISSION OF BROBO GROUP PTY LT ANGULAR: https://brobo.com.au/ WEIGHT: SHEET 1 OF 1...
5.1. Role of the Operator The person operating & maintaining the Brobo Group 3M Drill must familiarise themselves with these instructions for their own safety & that of the others, in addition to safeguarding the production of the machine. Responsibility must be taken by the user on the general maintenance &...
4) Clean & lubricate any moving joints or sliding surfaces with good quality oil. 5) Clean the drill machine regularly & keep any unpainted surfaces lightly oiled to protect from rust & corrosion. 6) Ensure that the machine performs drill perpendicular to the work surface. If not, contact Brobo Group engineering department.
CHAPTER 6 - Troubleshoot 6.1. General Troubleshooting Below lists of some of the most common problems associated with the Brobo Group 3M Drill & the recommended troubleshooting procedures to undertake to rectify the situation. If the solutions provided do not resolve the...
Page 35
For more information, please check www.brobo.com.au Replace worn/broken All component of the 3M drill is sold as spare Worn/broken component component parts (pending availability). Please contact your nearest Brobo distributor or our Brobo Group head office. Please visit www.brobo.com.au for more details.
Page 36
A.C.N. 098 264 316 A.B.N. 42 098 264 316 Quality BROBO GROUP (AUST) PTY. LTD. Endorsed Company 8 Fowler Rd, Dandenong, 3175 ISO 9001 Lic. 10292 Victoria, AUSTRALIA. Standards Australia Tel: 61 3 9792 9944 Email: info@brobo.com.au Fax: 61 3 9791 9955 Website: www.brobo.com.au...
Page 37
This warranty is given by Brobo Group Pty Ltd, ABN: 42 098 264 316 Address: 8 Fowler Rd, Dandenong South, VIC 3175 ✆...