Reloop AUDIO INNOVATE RMX INNOFADER Manual

Reloop Distribution
Global Distribution GmbH
Schuckertstr. 28
48153 Münster / Germany
Fax ++49/251/6099368
Subject to alterations.
Illustrations similar to original product.
Misprints excepted.
Copyright 2014
MINI INNOFADER CALIBRATION PROCEDURE 11/11/2012 by ELLIOT MARX
MOVE TO RIGHT END MOVE TO RIGHT END MOVE TO RIGHT END
MINI INNOFADER CALIBRATION PROCEDURE 11/11/2012 by ELLIOT MARX
1)
MOVE TO RIGHT END MOVE TO RIGHT END MOVE TO RIGHT END
1)
CALIBRATION BUTTON
CALIBRATION BUTTON
2)
2)
3)
3)
4)
4)
(OPTIONAL) SQUEEZE
5)
FURTHER FOR LESS
(OPTIONAL) SQUEEZE
5)
FURTHER FOR LESS
POWER CONNECTOR
POWER CONNECTOR
(OPTIONAL) SQUEEZE
FURTHER FOR LESS
DEAD SPACE
(OPTIONAL) SQUEEZE
FURTHER FOR LESS
DEAD SPACE
PRESS CALIBRATION BUTTON
MOVE TO RIGHT END
PRESS CALIBRATION BUTTON
MOVE TO RIGHT END
DEAD SPACE
DEAD SPACE
BEGINNING OF CALIBRATION:
MOVE THE FADER STEM ALL THE WAY
TO THE RIGHT. START WITH THE
BEGINNING OF CALIBRATION:
POWER OFF. MAKE SURE THE MIXER
MOVE THE FADER STEM ALL THE WAY
CABLE IS CONNECTED TO THE POWER
TO THE RIGHT. START WITH THE
CONNECTOR. FINALLY TURN ON THE
POWER OFF. MAKE SURE THE MIXER
POWER ONCE YOU HAVE CONFIRMED
CABLE IS CONNECTED TO THE POWER
THE CABLE IS CONNECTED.
CONNECTOR. FINALLY TURN ON THE
GRADUALLY MOVE THE STEM FROM POWER ONCE YOU HAVE CONFIRMED
THE CABLE IS CONNECTED. THE RIGHT END TO THE LEFT END.
IT SHOULD TAKE A MINIMUM OF 1/2
GRADUALLY MOVE THE STEM FROM
SECOND TO MOVE THE STEM FROM
THE RIGHT END TO THE LEFT END.
THE RIGHT END TO LEFT END.
IT SHOULD TAKE A MINIMUM OF 1/2
SLOW MOVEMENT IMPROVES
SECOND TO MOVE THE STEM FROM
CURVE ACCURACY.
THE RIGHT END TO LEFT END.
SLOW MOVEMENT IMPROVES
PRESS AND HOLD CALIBRATION FOR AT
CURVE ACCURACY.
LEAST 1/4 SECOND BEFORE RELEAS-
ING. YOU CAN REDUCE DEAD SPACE TO
PRESS AND HOLD CALIBRATION FOR AT
< 1.5mm BY SQUEEZING THE RUBBER
LEAST 1/4 SECOND BEFORE RELEAS-
PAD BEYOND THE NORMAL ENDPOINT
ING. YOU CAN REDUCE DEAD SPACE TO
WHILE PRESSING AND RELEASING THE
< 1.5mm BY SQUEEZING THE RUBBER
CALIBRATION BUTTON. EX: 0.5mm
PAD BEYOND THE NORMAL ENDPOINT
SQUEEZE = 1mm DEAD SPACE.
WHILE PRESSING AND RELEASING THE
CALIBRATION BUTTON. EX: 0.5mm
GRADUALLY MOVE THE STEM FROM
SQUEEZE = 1mm DEAD SPACE.
THE LEFT END TO THE RIGHT END.
IT SHOULD TAKE A MINIMUM OF 1/2
GRADUALLY MOVE THE STEM FROM
SECOND TO MOVE THE STEM FROM
THE LEFT END TO THE RIGHT END.
THE LEFT END TO RIGHT END.
IT SHOULD TAKE A MINIMUM OF 1/2
SLOW MOVEMENT IMPROVES
SECOND TO MOVE THE STEM FROM
CURVE ACCURACY.
THE LEFT END TO RIGHT END.
SLOW MOVEMENT IMPROVES
PRESS AND HOLD CALIBRATION FOR AT
CURVE ACCURACY.
LEAST 1/4 SECOND BEFORE RELEAS-
ING. YOU CAN REDUCE DEAD SPACE TO
PRESS AND HOLD CALIBRATION FOR AT
< 1.5mm BY SQUEEZING THE RUBBER
LEAST 1/4 SECOND BEFORE RELEAS-
PAD BEYOND THE NORMAL ENDPOINT
ING. YOU CAN REDUCE DEAD SPACE TO
WHILE PRESSING AND RELEASING THE