Vantage Hearth InFusion IC-DIN-II Install Manuals

V A N T A G E C O N T R O L S . C O M
2168 West Grove Parkway, Suite 300, Pleasant Grove, UT. 84062 USA
Telephone: 801 229-2800 ● Fax: 801 224-0355

Overview

The InFusion™ IC-DIN-II is Vantage's most
powerful automation controller to date,
featuring a new, extremely fast processor
improving processing performance.
Systems using the previous InFusion DIN
controller may be upgraded by simply
installing the new controller,* converting
the project file in Design Center 3.3 or higher, and downloading to
the new controller.
* See Replacing and/or Upgrading InFusion Controllers for
additional information.

Features


The InFusion Controller is the main "CPU" of Vantage's
complete systems integration solution

Automatic crossover support, RJ45 Ethernet connection.

Secure access – password protected

Design Center connection through local network or offsite
o
Firmware updates and full or minor program changes

Automatically
program code if update fails
o
Diagnostics
o
Read system
o
Project control

Built-in Ethernet jack

Type-A, USB port (future features ready)
o
The USB port is not used on IC-DIN-II controllers to
program from Design Center as in previous InFusion
controller models

Micro SD card support (included)

Automatic System Backups to micro SD card
o
Manually through front panel – real time
o
Within 24 hours of programming system
-then-
o
Weekly
o
Up to 52 backups total
o
Oldest backup is replaced when 52 limit is reached
o
Backups may be used to program system controllers

Restore entire system from System Backups
o
Undo option from last Restore

Ram and Flash memory

One controller supports up to 120 WireLink™ stations and up to
120 RadioLink™ stations

Local LCD interface provides limited control, status and
diagnostics

Lithium battery retains time and system status in a power
outage

Maintains real and astronomical time clocks

Design Center software is used to program the Controller

The Controller runs independent of a PC after initial setup and
programming

Application code is upgradeable through Design Center
software

InFusion Controllers operate as stand-alone or networked

Five RS-232 Ports

Two RS-485 Ports (shared with SE buses 3 and 4; simultaneous
RS-485 and SE bus connections are not possible)

Manual Override Switch

Reset Switch

Built-in Protection, electronic isolation between controllers

*The Vantage InFusion Controller Network can have up to
thirty-one Controllers when connected via Ethernet
*15 Controllers maximum on each Controller to Controller
Bus run.

InFusion Controller Specifications

Description
Dimensions HWD
Weight
Mounting
Power Requirement
©Vantage, 8/17/2016 / IS-0600-B
restores previous firmware
Specification
85.7mm x 157.2mm x 61.9mm
3.38" x 6.19" x 2.44"
417 g / 0.92 lb.
35 mm DIN Rail (EN 50 022: 1977)
36VDC/3.6A or 24VDC/2.5A
DIN InFusion Controller II — MODEL: IC-DIN-II
I N S T A L L A T I O N
DIN InFusion Controller II — MODEL: IC-DIN-II
Description
Power Supplies
Lightning / Surge
Protection Static Shock
IO. All ports/case
Bus Network
Max. Length of Combined
IC-II to IC-II
C2C, IC Network
Station Bus Specification
Station Bus Power
Supply, IC-36-1
Station Bus Power
Supply, IC-24-1
Max. Wire Length Station
and
Bus
Wire Configuration of
Station Bus
Max. # WireLink Stations
IC-36V
Max. # WireLink Stations
IC-24V
Cooling
Lithium Battery Backup
Ambient Operating
Temperature
Ambient Operating
Humidity
UL/cUL/CE/FCC Certified
Software/Firmware/Installation Requirements
Installation of
supervised by a Certified Vantage Installer. Design Center
Software, version 3.3.X.X or higher must be used to program
controller models with the "-II". Using IC-1 and IC-II controller
models on the same system, is not supported. Disconnect power
when plugging in or un-plugging the controller's power connector.
Use a dedicated breaker to power the controller. Multiple InFusion
Controllers may share the same breaker when in close proximity.

Powering the DIN Controller

The DIN Controller must be wired to Vantage's PSU36-DIN 130W,
36VDC or ACPDXXSM2 60W, 24VDC power supply. Power
supplies must be mounted to 35mm DIN rail in any standard DIN
Enclosure compatible with the maximum power dissipated. Before
using pull out the lithium battery tab insulator on the DIN
Controller. Connect the positive (+) output of the power supply to
the 24V/36V screw terminal and the negative side to one of the
ground terminals. The Controller and Power Supply must be earth
grounded. Carefully follow the Wiring Diagrams below. DO NOT
USE ANY OTHER POWER SUPPLY*.
*NOTE: Another (Vantage Certified) 96W, 24VDC power supply,
DIN POWER-MC, is also available in the European region from
Vantage EMEA; visit, www.vantage-emea.com.
NOTE: The earth ground on the DIN Controller and power supply
should be the ONLY earth ground connection in this DIN
Controller's immediate
between controllers) connections are isolated so a new earth
ground reference for each Controller is normal.

Vantage recommends a minimum 0.75mm
stranded, between the power supply and the controller.

Recommended: keep wires no longer than 1 meter between
the power supply and the controller.
V A N T A G E I N S T A L L G U I D E S
Specification
 PSU36-DIN – 130W, 36VDC
 ACPDXXSM2 – 60W, 24VDC
 DIN POWER-MC – 96W, 24VDC, Europe
IEC 61000-4-2
Low Voltage, ITU-T K.20
2000ft / 609m- using 16-18AWG
2
/ 1.31-0.75mm , 2-conductor, twisted pair,
non-shielded wire
Ethernet (see Screen 16, p. 3)
2C, 16AWG / 1.31mm2, twisted, non-shielded,
<30pF per foot. Separate a minimum of 12" /
30.5cm from other parallel communication
and/or high voltage runs.
Each station bus run has a 60W power supply;

Station Bus Run 1 = 60W

Station Bus Run 2 = 60W
Shared, 35W max. power supply combined to
both station bus runs.
609m / 2,000ft of cabling max. on each
station bus. No station more than 305m /
1,000ft from Controller.
Daisy Chain, Branch, Star
(contact support for
Station Bus Best Practices)
Up to 60 Stations each bus or until the 60W
supply per bus is used
Up to 50 Stations each bus or until the
shared 35W supply is used
Convection
Disk battery CR2032, 3Volt
2.5 yrs. un-powered or 20 yrs. powered (field
replaceable – see Caution at end)
0-40°C / 32-104°F
5-95% non-condensing
YES
Vantage products should
system. Controller
be performed or
Bus (connections
2
/ 18AWG wire,
page 1 of 7