Related Manuals for Taurus TITANIUM RT-BS 75
Summary of Contents for Taurus TITANIUM RT-BS 75
- Page 1 850W BELT SANDER INSTRUCTION MANUAL MODEL NUMBER RT-BS 75 AFTER SALES SUPPORT TEL: 1300 922 271 N26704 EMAIL: service.australia@einhell.com...
-
Page 2: Table Of Contents
Congratulations on choosing to buy a TAURUS TITANIUM® product. All products brought to you by TAURUS TITANIUM® are manufactured to the highest standards of performance and safety, and, as part of our philosophy of customer service and satisfaction, are backed by our comprehensive Year Warranty. - Page 3 After Sales Support TEL: 1300 922 271 EMAIL: service.australia@einhell.com...
- Page 4 After Sales Support TEL: 1300 922 271 EMAIL: service.australia@einhell.com...
- Page 5 After Sales Support TEL: 1300 922 271 EMAIL: service.australia@einhell.com...
-
Page 6: General Safety Rules
c. Avoid accidental starting. Ensure the switch is in 1. GENERAL SAFETY RULES the off-position before plugging in. Carrying power tools with your finger on the switch or WARNING! Read all instructions Failure to plugging in power tools that have the switch follow all instructions listed below may result on invites accidents. -
Page 7: Layout
5. Service 2. Layout a. Have your power tool serviced by a qualified 1. Screw to adjust the additional handle repair person using only identical replacement 2. Additional handle parts. This will ensure that the safety of the power tool is maintained. 3. Setting wheel for belt speed 6. Recommendation 4. Locking button We recommend that the tool always be supplied 5. ON/OFF switch via a residual current device with a rated residual current of 30 mA or less. -
Page 8: Before Starting The Equipment
Wear ear-muffs. The dust is extracted directly via the sanding belt into the dust container. The impact of noise can cause damage to hearing. Total vibration values (vector sum of three IMPORTANT! directions) determined in accordance with EN For health safety reasons it is imperative that you 60745. use a dust container or a dust extraction system via Handle the dust extraction adaptor! Vibration emission value a ≤ 2.5 m/s 5.2 Adjusting the additional handle (Fig. 5/Item 2) K uncertainty = 1.5 m/s Additional handle Slacken the screw (1) and move the additional Vibration emission value a ≤ 2.5 m/s handle (2) to its optimal position. Lock the K uncertainty = 1.5 m/s additional handle (2) in place by tightening the screw (1). IMPORTANT! 5.3 Changing the sanding belt (Fig. 6-7/Item 13) The vibration value changes according to the area • Pull the clamping lever (12) to the outside to of application of the electric tool and may exceed relieve the tension in the sanding belt. -
Page 9: Starting Up
6. Starting up 8. Cleaning, maintenance and ordering of spare parts 6.1 Switching ON/OFF (Fig. 11) Always pull out the mains power plug before To switch on: starting any cleaning work. Press the ON/OFF switch (5). 8.1 Cleaning Continuous operation: Secure the switch (5) with the locking button (4). • Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. To switch off: Press the ON/OFF switch (5) briefly. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure. The machine can be operated on a temporary or permanent setting. • We recommend that you clean the device immediately each time you have finished using it. 6.2 Setting the belt speed (Fig. 12/Item 3) • Clean the equipment regularly with a moist cloth You can select the belt speed by turning the setting and some soft soap. Do not use cleaning agents... - Page 10 After Sales Support TEL: 1300 922 271 EMAIL: service.australia@einhell.com...
- Page 11 After Sales Support TEL: 1300 922 271 EMAIL: service.australia@einhell.com...
- Page 12 08/2012 Art.Nr: 44.662.35_11012 (01) After Sales Support TEL: 1300 922 271 EMAIL: service.australia@einhell.com...
Need help?
Do you have a question about the TITANIUM RT-BS 75 and is the answer not in the manual?
Questions and answers