Table of Contents
Advertisement
Quick Links
LANIER R/C
Wingspan....
62"
Wing Area...
687 sq. in.
Weight........
6 – 7 lbs.
Wing Loading...
21-23 oz./sq. ft.
Fuselage Length...
48"
Engine Required ...
2-Stroke .40 - .50
WARRANTY .................. Lanier R/C is proud of the care and attention that goes into the manufacture of parts for
its model kits. The company warrants that for a period of 30 days, it will replace, at the buyers request, any parts or
material shown to the company's satisfaction to have been defective in workmanship or material at the time of
purchase.
Important Information
The bottom of the hull is covered with fiberglass. The iron on covering does
not stick well to the fiberglass. It is your responsibility to keep the edges of
the covering ironed down so the covering does not come off. The bottom of
the hull receives a lot of abrasion and the covering coming loose is not
COVERED UNDER WARRANTY. Due to temperature changes the plane may
develop some wrinkles in the covering that you will need to remove with an
iron. Be sure to seal the edges down first so that you do not cause the
covering to shrink and leave exposed areas of wood. Please inspect the
LANIER R/C, INC.- P O Box 458 - Oakwood, GA 30566 - Ph 770-532-6401
Assembly Instructions
MARINER
1
© Copyright 2001 Lanier R/C Inc.
.40
Advertisement
Table of Contents
Related Manuals for Lanier R/C MARINER .40
Summary of Contents for Lanier R/C MARINER .40
- Page 1 2-Stroke .40 - .50 WARRANTY ……………… Lanier R/C is proud of the care and attention that goes into the manufacture of parts for its model kits. The company warrants that for a period of 30 days, it will replace, at the buyers request, any parts or material shown to the company's satisfaction to have been defective in workmanship or material at the time of purchase.
- Page 2 This one year limitation is imposed by agreement of the parties as permitted by the laws of the state of Georgia. LANIER R/C, INC.- P O Box 458 - Oakwood, GA 30566 - Ph 770-532-6401...
-
Page 3: Wing Assembly
(not supplied) to the servo case to hold it in position. Cut 4 pieces of 3/8” sq. hardwood, 2 for each servo. Square up the ends. Epoxy one LANIER R/C, INC.- P O Box 458 - Oakwood, GA 30566 - Ph 770-532-6401... - Page 4 Place the servo board in the wing opening. Drill four 1/16” holes in each corner 1/8” in from each side. Use the #2 x 3/8” screws provided. LANIER R/C, INC.- P O Box 458 - Oakwood, GA 30566 - Ph 770-532-6401...
- Page 5 #11 Exacto blade, so that wire better screw alignment to the nut plate on the will lay flat against float strut. far side. Now fasten in place with the hardware supplied. LANIER R/C, INC.- P O Box 458 - Oakwood, GA 30566 - Ph 770-532-6401...
- Page 6 Wipe any excess epoxy from the wing joint and clean any glue residue with rubbing alcohol. Hold the wing together with masking tape. The masking tape will retain the LANIER R/C, INC.- P O Box 458 - Oakwood, GA 30566 - Ph 770-532-6401...
-
Page 7: Tail Assembly
Careful, do not parts are assembled remove beyond the end of the dorsal fin mark. LANIER R/C, INC.- P O Box 458 - Oakwood, GA 30566 - Ph 770-532-6401... - Page 8 5. Remove the covering between the lines. sure it is perpendicular with the stab. Use a square and tape the fin in place. Now glue on LANIER R/C, INC.- P O Box 458 - Oakwood, GA 30566 - Ph 770-532-6401...
- Page 9 Install the hinge in the rudder and epoxy the fin in place. The rudder and hinge will keep it LANIER R/C, INC.- P O Box 458 - Oakwood, GA 30566 - Ph 770-532-6401...
- Page 10 Do the pushrod 3/8”. Install the hex nut and screw not glue in place yet. on a clevis. Do two pushrods. LANIER R/C, INC.- P O Box 458 - Oakwood, GA 30566 - Ph 770-532-6401...
- Page 11 2. The engine mount is adjustable to fit many sizes of engines. Adjust the mount to fit your engine and tape it together, but first it LANIER R/C, INC.- P O Box 458 - Oakwood, GA 30566 - Ph 770-532-6401...
- Page 12 You will also need one for the other side. Notch out for mast to allow for cowl adjustment fore and aft. LANIER R/C, INC.- P O Box 458 - Oakwood, GA 30566 - Ph 770-532-6401...
- Page 13 3/32” drill bit. Now mark and drill the other beam mount as stated 11. Install four #2 x 3/8” sheet metal screws to above. retain the cowl in place. LANIER R/C, INC.- P O Box 458 - Oakwood, GA 30566 - Ph 770-532-6401...
- Page 14 File all sharp corners on tubing end so fuel line will not be cut. Make sure inside of tank is clean before installing stopper on tank. LANIER R/C, INC.- P O Box 458 - Oakwood, GA 30566 - Ph 770-532-6401...
- Page 15 1. Locate the mast support. Notch off the forward lower edge of the mast to miss possible glue gob at the bulkhead/keel joint. LANIER R/C, INC.- P O Box 458 - Oakwood, GA 30566 - Ph 770-532-6401...
- Page 16 The removed to allow it to fit. lifters are necessary to help break the vacuum sometimes occurring at the step. LANIER R/C, INC.- P O Box 458 - Oakwood, GA 30566 - Ph 770-532-6401...
-
Page 17: Installing The Windshield
Water Resistant however, expect to pay more money. Of course, if they are submerged, forget it. If LANIER R/C, INC.- P O Box 458 - Oakwood, GA 30566 - Ph 770-532-6401... -
Page 18: Getting Ready To Fly
When cured, remove the wing and wax paper LANIER R/C, INC.- P O Box 458 - Oakwood, GA 30566 - Ph 770-532-6401... -
Page 19: Charge The Batteries
Just above the water start to flair and hold it off time with the Mariner, tuning it up for great in the ground effect, or is that water effect? water handling, and ease of lift off. LANIER R/C, INC.- P O Box 458 - Oakwood, GA 30566 - Ph 770-532-6401... - Page 20 Plastic propeller suitable for engine Moto-tool with cut-off wheel .40 to.50 size engine Tube: GE Silicone Sealer 4 channel radio with 5 servos Lead weight three 6” servo extension leads LANIER R/C, INC.- P O Box 458 - Oakwood, GA 30566 - Ph 770-532-6401...
- Page 21 4-40 clevis 4-40 hex nuts 4-40 threaded rod x 1" 2 Parts bag #2 Motor mount left Motor mount right E-Z connector "T" style control horn 4 LANIER R/C, INC.- P O Box 458 - Oakwood, GA 30566 - Ph 770-532-6401...