Table of Contents
Advertisement
INSTALLATION
Mounting Guidelines
• Mount the unit as low as possible near the
center of the windshield.
• Do not mount your unit behind wipers,
ornaments, mirrored sunscreens, etc. These
obstructions have metal surfaces which can
affect radar and laser signals and reduce
critical warning time. (Regular tinted glass
does not affect reception.)
• Some windshields have an Instaclear
Electriclear
™
type coating, which affects radar
signals. Consult your dealer or the vehicle's
owner's manual to determine if your windshield
has this coating.
• Avoid placing unit in direct contact with wind
shield.
• To reduce the possibility of theft, conceal your
unit when not in use.
Windshield Mounting
• Install the two suction cups and rubber bumper
onto the bracket by fitting them into their holes.
• Press the suction cups onto the windshield at the
location you have chosen. (Image A)
(Image A)
Important: S ome newer cars have a plastic safety
coating on the inside of the windshield. The
windshield bracket may leave permanent marks on this
type of surface. To find out if your vehicle has this type
of windshield, check the vehicle's owner's manual or
ask your dealer.
5
We recommend that you do not leave the suction
cup bracket on the windshield in direct sunlight. If the
detector is removed, this may cause blistering of
the dash in some vehicles.
• Slide the detector onto the bracket until it locks into
place. (Image B)
™
or
• If necessary, the unit may be leveled by bending the
windshield bracket. Press the bracket release button
and remove the detector before bending.
Power Cord Connection
• Plug the small end of the power cord into the
unit' s power jack.
• Plug the large end into the vehicle' s cigarette lighter.
N N o o t t e e : : Cord fits tightly into detector. When
installing the cord, expect some resistance.
Fuse Replacement
The lighter socket plug is equipped with a
replaceable 2 amp, 3AG fuse located behind the
Windshield
silver tip. To replace the fuse, carefully unscrew
Mounting
the tip of the plug.
I I m m p p o o r r t t a a n n t t : : Unscrew slowly. The tip contains a
spring which may fly out when disassembling.
Insert the new fuse with the spring and screw on
the tip. With use, screw cap on plug may loosen.
Retighten occasionally.
Unscrew the tip of the lighter socket plug
carefully when replacing the 2 amp fuse.
INSTALLATION
(Image B)
Rubber Bumper
6
OPERATION
Power On and Self-Test
Each time your Whistler detector is turned on, an
automatic self-test sequence confirms that the
speaker and display are functional.
• Press Power. Display indicates (in order):
1. X-Band
2. K-Band
3. Ka-Band
6. P (POP)
Setting Saver
Setting Saver saves your personalized settings so
that when the detector is turned off and then on
again, you do not have to re-enter them.
Feature Engaged Confirmation
Each time a button is pressed one beep confirms
feature "on", two beeps confirm feature "off".
Audio Level Adjustment
The audio levels can be adjusted high to low or low to high.
• Rotate Power/Volume button back to increase audio level.
• Rotate Power/Volume button forward to decrease audio level.
As audio level is adjusted, beeps are provided and
the display indicates volume level.
Self Test Mute
Simply press the Quiet button during the self-test
sequence to cancel the self-test audio. This will not
affect radar/laser alerts. To restore the self-test
audio, simply press the Quiet button during the next
self-test.
Quiet Mode
Quiet cancels audio during an alert and any new
alert within 20 seconds. After 20 seconds of no
alerts, the audio is restored for any new alerts.
• Press Quiet to cancel the audio.
• Press Quiet a second time during an alert to
restore the standard audio alert pattern; or turn the
unit off, then on.
7
5. LASER
Advertisement
Table of Contents
