Axxess AX-ADGM04 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Axxess Manuals
  4. Cables and connectors
  5. AX-ADGM04
  6. Installation instructions manual

Axxess AX-ADGM04 Installation Instructions Manual

Gm data interface 2012-2016
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INTERFACE FEATURES
• Provides accessory power (12-volt 10-amp)
• Maintains the retained accessory power
(R.A.P.) feature
• Provides NAV outputs (parking brake,
reverse, speed sense)
• Retains chimes
† To retain fade in digital amplified models, use the AX-ADBOX1
INTERFACE COMPONENTS
• AX-ADGM04 harness
• 4-pin to 4-pin resistor pad harness
APPLICATIONS
See inside front cover
AxxessInterfaces.com
GM Data Interface
INTRODUCTION
The AX-ADGM04 harness is designed for, and must be used with, the
AX-ADBOX1 or AX-ADBOX2 interface (sold separately). Please refer to the
AX-ADBOX1 or AX-ADBOX2 for the 16-pin connector with stripped leads.
• Retains OnStar / OE Bluetooth
• Adjustable OnStar level
• Retains RSE (rear seat entertainment)
• Retains satellite radio
• Retains the factory AUX-IN jack
© COPYRIGHT 2018 METRA ELECTRONICS CORPORATION
2012-2016
• Pre-wired ASWC-1 harness
(ASWC-1 sold separately)
• Can be used in non-amplified, or analog/
digital amplified models
• Retains balance and fade†
• Micro "B" USB updatable
AX-ADGM04
I N S TA L L AT I O N I N S T R U C T I O N S

TABLE OF CONTENTS

For models without an amplifier .......................3
12-pin pre-wired ASWC-1 harness ......................6
DIN jack ................................................................6
AX-ADBOX1 ...........................................................6
AX-ADBOX2 ..........................................................7
Adjusting the AX-ADGM04 ....................................8
Extra features .........................................................9
TOOLS REQUIRED
• Crimping tool and connectors, or solder gun, solder,
and heat shrink • Small flat-blade screwdriver • Tape
• Wire cutter • Zip ties
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
REV. 6/20/18 INSTAX-ADGM04

Advertisement

Table of Contents
loading

Related Manuals for Axxess AX-ADGM04

Summary of Contents for Axxess AX-ADGM04

  • Page 1: Table Of Contents

    For models without an amplifier .......3 INTRODUCTION For models with an analog amplifier ....4 The AX-ADGM04 harness is designed for, and must be used with, the For models with a digital amplifier ....5 AX-ADBOX1 or AX-ADBOX2 interface (sold separately). Please refer to the 12-pin pre-wired ASWC-1 harness ......6...
  • Page 2 APPLICATIONS CADILLAC CHEVROLET CHEVROLET (CONT) Escalade † 2012-2014 Avalanche ‡ * 2012-2013 Silverado 2500 / 3500 ‡ * 2014 Savana ‡ 2013-2015 Escalade ESV † 2012-2014 Express ‡ 2013-2015 Silverado ‡ * 2012-2013 Sierra 2500 / 3500 ‡ * 2014 Escalade EXT †...

  • Page 3: Connections To Be Made

    • Disregard the Pink wire with a red connector, it will not be used in this application. • Connect the Green/Purple wire to the reverse wire. Note: The relay attached to the AX-ADGM04 harness is only for audible turn signal clicks. No extra steps are required to retain this feature, so leave the relay as-is.

  • Page 4: For Models With An Analog Amplifier

    • Disregard the Pink wire with a red connector, it will not be used in this application. The following (3) wires are only for multimedia/navigation radios that require these wires. Note: The relay attached to the AX-ADGM04 harness is only for audible turn signal clicks. • Connect the Blue/Pink wire to the VSS/speed sense wire.

  • Page 5: For Models With A Digital Amplifier

    Green, Green/Black, Pink (with a red connector), Purple, Purple/Black • Connect the Green wire to the left rear positive speaker output. Note: The relay attached to the AX-ADGM04 harness is only for audible turn signal clicks. • Connect the Green/Black wire to the left rear negative speaker output.

  • Page 6: 12-Pin Pre-Wired Aswc-1 Harness

    • Connect the AX-ADGM04 harness to the wiring harness in the vehicle. entertainment, satellite radio, AUX-IN. • If an ASWC-1 (sold separately) will be used, do not connect it until the AX-ADGM04 is programmed and fully functional. Programming the AX-ADGM04 Attention! If the interface ever loses power, the following steps will need to be performed again.

  • Page 7: Ax-Adbox2

    1. The Blue reset button is located inside the interface, between the two connectors. The button is accessible outside the interface, no need to open the interface. • If an ASWC-1 (sold separately) will be used, do not connect it until the AX-ADGM04 is programmed and fully functional.

  • Page 8: Adjusting The Ax-Adgm04

    • Once at a desired level, audio level adjustment is complete. • If the vehicle does not come equipped with steering wheel controls, locate the Black/Yellow wire on the AX-ADGM04 harness. Chime level adjustment: • While OnStar is speaking, tap the Black/Yellow wire to ground. Once the OnStar level is set, •...

  • Page 9: Extra Features

    • If the vehicle is equipped with AUX-IN, rear seat entertainment, or satellite radio, the AX-ADGM04 can retain these features. • SEEK UP - Scrolls menu up. • Change the source of the radio to AUX-IN; satellite radio will start playing.
  • Page 11 REV. 6/20/2018 INSTAX-ADGM04...
  • Page 12 AX-ADGM04 I N S TA L L AT I O N I N S T R U C T I O N S IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated.

Table of Contents