Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Nortik Scubi 2
Summary of Contents for Nortik Scubi 2
- Page 1 Assembly instructions nortik scubi 2 Recreational kayak QR-Code assembly video:...
- Page 2 After some practice, you will assemble the nortik scubi 2 easily within 10 minutes! Please note that there is an assembly video on youtube: https://www.youtube.com/faltboot_de...
- Page 3 1) Parts overview #1 1x Hull #2 2x Stem element (bow and stern = identical) #3 4x Keel rod #4 2x Cross ribs for front seat 1x open (lower than for rear seat) 1 x closed (wider than for rear seat) #5 2x Cross ribs for back seat 1x open, 1 x...
- Page 4 3) Assembly General proceeding: First you assemble the keel rods and the stem and insert them into the hull. Then mount the cross ribs and at last inflate the sponsons. First unfold the hull and take one of the stem elements (they are identical).
- Page 5 Make sure everything sits centrally. Fold the support rod upwards and clip it into the cross tube. cross tube support rod Then take the stern element and the keel rod shown on the picture (with the arrow marking positioned in the rear).
- Page 6 Proceed in the same way as with the bow. Stern-Section Slide the keel rod under the back seat and push it through the sleeve on the hull before clipping it to the stem keel rod element. sleeve Push the stem element as far as possible into the stern Then fold the flexible rod upwards and clip it from...
- Page 7 Place the keel rods under the seats and slide them through the sleeves on the hull before clipping them to the rods you have already installed to the bow-/ stern-section. sleeve sleeve...
- Page 8 First make sure, that bow- and stern element still are in a central position. Then take out the split pin. Pull up the two middle keel rods. IMPORTANT: Do not grab the rods too close to the ends, but at least a length of the riveted half-tube away from it! (see picture on the left) Pull them both up, until you can fit the...
- Page 9 Push the split pin through the two rods… …and put the rubber band around to secure it. Now install the cross ribs. First take the closed cross rib for the front seat (#4 in the part overview). Push the boat skin a bit aside and place the cross rib behind the front seat diagonally onto the clip on the keel rod.
- Page 10 Then right it slowly up, while the clips interlock. When the cross rib sits upright, clip in the seat bars on the back side of it. (see picture below) Note: If this is hard to do, slide the seat cloth as far as possible towards the bow Then take the open cross rib for the front seat (#4 in the part overview).
- Page 11 Then press the C-Clip onto the keel rod Follow the same procedure with the remaining cross ribs (#5 in the part overview) for the back seat.
- Page 12 Now inflate the high pressure sponsons. IMPORTANT: There is an adapter for the filling valves in the repair kit. Put it onto the double action pump. Then insert the adapter into the valve and with a half turn screw it to it. The inflating valves have to positions that you can adjust by pushing and turning the white pin in the middle.
- Page 13 4) Solo use If you want to paddle your nortik scubi 2 alone, you can do that from the front seat. You will have to use the stern as bow (the front seat is around 35 cm more in the middle of the boat.)
- Page 14 5) Installation of the Deck Mount the deck from the stern. Place it in such wise, the deck just covers the Velcro on the boat. It will overlap a little in the back. (see picture on the left) Then mount it completely and make sure to tauten it.
- Page 15 5) Installation of the rudder system The rudder system can be used on both sides of your nortik scubi 2. Both, bow and stern have a pickup for the rudder blade. This allows you to use the rudder system either in solo use, or when paddling in pairs.
- Page 16 Take the pull-up clip (with Velcro underneath) and lead the pull-up line through it. Then lead the two steering ropes through the holes of the cross beam… ...and turn them around. They will lock themselves by being tensioned. Now lead the extensions of the steering lines (with chains) from behind under the cross rib of the middle seat.
- Page 17 Then lead the whole extension through the loop. Now you have attached the extension to the cross rib. Lead the two steering lines from behind through the two D-rings, on which the back rest is attached. Now knot the steering line to the last chain link of the extension.
- Page 18 By pushing the bar with your feet you can now change the direction of the rudder blade. Lead the end of the pull-up rope back through pin and attach it to the rudder with the carabiner. 8) Instructions for disassembling The disassembling corresponds the assembling in reverse order.
- Page 19 Bow-section So you can get the hull back into the bag easily.
- Page 20 Then push the patch firmly onto the hull. On tour: The nortik scubi 2 can be reused shortly after repair. However, the adhesive and protective effect still improves within 12 hours when the adhesive is completely dried. The sponson can be repaired in the same procedure as described above.
- Page 21 For more information about your and other products, sources of supply and downloads at any time:...
Need help?
Do you have a question about the Scubi 2 and is the answer not in the manual?
Questions and answers