Quoizel BKR8410IA Installation Manual

Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (1) A21 Medium Base Vintage Bulb 150W Maximum, bulb included.
Estimated Assembly Time:
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact your original place of purchase.
Fixture can only be mounted in the direction indicated on page 2.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
Crossbar
A
Assembly
x 1
Alternate
B Mounting screw
x 2
-
STEP 1 Install Crossbar Assembly
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
Outlet Box
Supply Wires with
Ground Wire
-
STEP 2 Fit Backplate to
Crossbar Assembly
A. Remove mounting balls from
the Crossbar Assembly (A).
Fit the backplate on Fixture
Body (C) to the Crossbar
Assembly (A) and secure with
mounting balls. Note: The
backplate on Fixture Body (C)
should be snug against the
wall and the mounting balls. If
not, adjust the length of the
mounting screw or alternate
short mounting screw on the
Crossbar Assembly (A) by
unscrewing the
preassembled hex nut and
20-30 minutes
Fixture
C Body
x 1
Socket Collar
F
x 2
G
.
Mounting Screw
or Alternate Short
Mounting Screw
Figure 1
A
Outlet Box Screws
(not included)
Backplate
Mounting Ball
Mounting Screw
or Alternate Short
Mounting Screw
A
Hex Nut and
Lock Washer
Figure 2
Installation Guide
(Step 2 Continued)
Shade
D
x 1
Lock washer and then screwing the mounting screws or alternate
short mounting screws in or out of the crossbar until the correct
length is achieved. Once the backplate on Fixture Body (C) is
secure, remove the mounting ball and Fixture Body (C) and proceed
to Step 3.
Wahser
E
x 1
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
Edison Bulb
B. Use standard wire connectors (not included) to make all wire
x 1
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
from outlet box
Black wire from
outlet box (or Red)
Bare, or Green
Ground wire
from outlet box
-
STEP 4 Install Fixture Body
A. Carefully tuck all wires into the outlet box and position the backplate
of fixture body (C) over the outlet box. Align the holes in the
backplate with the
mounting screws or
alternate short mounting
screws. Secure with the
C
previously removed
mounting balls and hand
tighten until snug.
1of2
White wire
Green Ground Screw
on the Crossbar
Mounting Screw
or Alternate Short
Mounting Screw
Figure 4
White wire
from fixture
Black wire
from fixture
Ground wire
from Fixture
Figure 3
Backplate
Mounting Ball
C
A