Quoizel BKR8408K Assembly Instruction Sheet

Please go to www.quoizel.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (1) Medium Base Decorative Filament 60W bulb (provided), Maximum 100W, Alternate bulb (1) 23W CFL Maximum.
Estimated Assembly Time:
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Fixture can only be mounted in the direction indicated on page 2.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
Crossbar
A Assembly
x 1
Alternate
Mounting
B
screw
x 2
-
STEP 1 Install Crossbar Assembly
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
Outlet
Box
Mounting Screw
or Alternate Short
Mounting Screw
-
STEP 2 Fit Backplate to
Crossbar Assembly
A. Remove mounting balls from
the Crossbar Assembly (A).
Fit the backplate on Fixture
Body (C) to the Crossbar
Assembly (A) and secure with
mounting balls. Note: The
backplate on Fixture Body (C)
should be snug against the wall
and the mounting balls. If not,
adjust the length of the mounting
screw or alternate short mounting
screw on the Crossbar Assembly
(A) by unscrewing the
preassembled hex nut and lock
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2015 QuoizelInc.
Assembly Instruction Sheet #IS-BKR8408K
for product cleaning tips. Go to the
20-30 minutes
D
Fixture
C Body
x 1
E
Socket Collar
F
x 1
.
Outlet Box Screws
(not included)
A
Supply Wires
with Ground Wire
Backplate
Mounting Ball
Mounting Screw
or Alternate Short
Mounting Screw
A
Hex Nut and
Lock Washer
Figure 2
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
For Style BKR8408K
Care + Maintenance selection.
(Step 2 Continued)
Shade
x 1
washer and then screwing the mounting screws or alternate short
mounting screws in or out of the crossbar until the correct length is
achieved. Once the backplate on Fixture Body (C) is secure, remove
the mounting ball and Fixture Body (C) and proceed to Step 3.
Wahser
x 1
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
Edison
connectors until wires are tightly joined together. Wrap each
G Bulb
connection with approved electrical tape and carefully stuff all the
x 1
connected wires into the Outlet Box.
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
-
STEP 4 Install Fixture Body
A. Carefully tuck all wires into the outlet box and position the backplate
of fixture body (D) over the outlet box. Align the holes in the
backplate with the mounting
screws or alternate short
mounting screws. Secure
Figure 1 with the previously
removed mounting balls
and hand tighten until
snug.
C
-
STEP 5 Install Shade to Fixture Body
A. Place Shade (D) and the Washer (E) over the Socket as shown.
Secure by threading the Socket Collar (F) onto the Socket. Hand
tighten until sung.
B. This fixture uses Medium Base Decorative Filament 60W bulb (G),
1of2
White wire
from fixture
Black wire
from fixture
Ground wire
from fixture
Figure 3
Backplate
Mounting Screw
Mounting Ball
or Alternate Short
Mounting Screw
A
Figure 4
September2015
B