Table of Contents
Advertisement
Quick Links
Current Tools
Model 750 — ½" to 1"
RIGID and IMC conduit and schedule 40 Pipe
Operating, Maintenance, Safety
and Parts Manual
This manual is free of charge. All personnel who operate the
Mechanical Bender should have a copy of this manual and read
and understand its contents. To request a copy, call or write to
the address below.
CURRENT TOOLS • P. O. BOX 17026 GREENVILLE, SC 29606
800.230.5421 or 864-721-4230 • FAX 864-721-4232
Mech anical Bender
™
Read and understand this material before
operating or servicing the Mechanical Bender.
Failure to understand how to safely operate
and service this unit could result in serious
injury or death.
www.currenttools.com
06/11 REV. 4
Advertisement
Table of Contents
Related Manuals for Current Tools 750 Tweaker
Summary of Contents for Current Tools 750 Tweaker
- Page 1 Mechanical Bender should have a copy of this manual and read and understand its contents. To request a copy, call or write to the address below. CURRENT TOOLS • P. O. BOX 17026 GREENVILLE, SC 29606 800.230.5421 or 864-721-4230 • FAX 864-721-4232 www.currenttools.com...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Safety Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Information . -
Page 3: Safety Information
RETAIN SAFETY INFORMATION This manual should be read and understood by all personnel who operate or service this Mechanical Bender. Failure to understand how to safely operate and service this unit could result in injury or death. This unit should only be operated or serviced by qualified personnel. IMPORTANT SAFETY INFORMATION Follow ALL safety information provided by the manufacturer. -
Page 4: Specifications
SPECIFICATIONS Model No. Capacity ½" to 1" RIGID and IMC conduit and schedule 40 pipe Overall Dimensions 48" L x 24 ½" W x 30" H Weight 91 lbs. OPERATING INSTRUCTIONS 1. Cut a 5' length of 1" RIGID conduit and insert it into the ratchet arm as shown in Figure 1. -
Page 5: The Tweaker
THE TWEAKER ™ The TWEAKER™ feature allows the operator to correct overbends of 3º or less on ½"– ¾"– 1" RIGID/IMC conduit or schedule 40 pipe. To use the TWEAKER™: 1. Insert the conduit between the TWEAKER ™ shafts shown on Figure 2. 2. -
Page 6: Stub Bending Information
STUB BENDING INFORMATION To locate bending marks for stubs: 1. Check the Stub Dimensions Chart (below) for Minimum Stub Length. The stub being bent must be equal to or longer than the Minimum Stub Length. 2. Measure and mark the stub length required on the conduit. This is the stub length mark. -
Page 7: Offset Bending Information
OFFSET BENDING INFORMATION To mark conduit for offsets: 1. Measure distance from end of conduit to start of first bend and mark conduit. This is mark #1. See Figure 1 and 2. 2. Refer to Deduct Chart and deduct this length from mark #1 and place mark #2 on conduit. -
Page 8: Exploded View
EXPLODED VIEW — Model 750 Mechanical Bender... -
Page 9: Parts List - Model 750 Mechanical Bender
PARTS LIST — Model 750 Mechanical Bender ITEM # PART # DESCRIPTION 1 ... 750-1..1 ....BENDING SHOE 2 .
Need help?
Do you have a question about the 750 Tweaker and is the answer not in the manual?
Questions and answers