Niveo Professional NWA220 User Manual

11 ac 1200mbps outdoor cpe

Hide thumbs Also See for NWA220:

Hardware and operation mode instruction (32 pages)

User manual (27 pages)

page of 23

/ 23
Bookmarks

Quick Links

Download this manual

User Manual of 11 ac 1200Mbps Outdoor CPE NWA220

This is the user manual of 11ac 1200Mbps Outdoor CPE, which will approximate guide

you how to set and apply the NWA 200 Outdoor CPE

More information:

WWW.NIVEOPROFESSIONAL.COM

INFO@NIVEOPROFESSIONAL.COM

Summary of Contents for Niveo Professional NWA220

Page 1 User Manual of 11 ac 1200Mbps Outdoor CPE NWA220 This is the user manual of 11ac 1200Mbps Outdoor CPE, which will approximate guide you how to set and apply the NWA 200 Outdoor CPE More information: WWW.NIVEOPROFESSIONAL.COM INFO@NIVEOPROFESSIONAL.COM All rights reserved Niveo International BV 2020...
Page 2 Hardware and Operation mode instruction WAN: Gigabit WAN Port, connect with ADSL modem or Internet mainly. It will be LAN port under Outdoor CPE and WiFi Repeater operation mode. Power Supply: Powered by PoE Switch The connection diagram shows as P2, Internet cable from PoE Switch to Outdoor CPE’s WAN Port, then PC access into Outdoor CPE wired/wireless.
Page 3 : Login Default IP: 192.168.2.200 Username: admin Password: admin 1）Connect the Outdoor CPE with computer 2）Configure the PC’s local connection IP address as 192.168.2.X (X is number from 2 to 254), subnet mask is 255.255.255.0. 3) Input 192.168.2.200 into IE browser, then pop up the login page, the default login user name: Admin, Passwords: admin.
Page 6 2) Wizard Configuration: Click Wizard in Status page, will pop up following page to configure the operation mode: There are four operation mode of this ceiling Outdoor CPE, and there are explanation for each operation mode for better application. Operation mode 1.
Page 8 When click Next, then will complete the Gateway mode setting and show following picture: Complete the setting in Gateway Mode When return to Status, the page showed as follow: Status in Gateway Mode All rights reserved Niveo International BV 2020...
Page 9 2. WiFi Repeater mode Click WiFi Repeater operation mode in Wizard, then following page will pop up, and choose the right SSID to bridge, then next. Repeater Mode After click Next button, then should configure the wireless setting as follow, then click Next to finish: P17 Wireless Setting in Repeater Mode All rights reserved Niveo International BV 2020...
Page 10 Click Return button, will back to Status, show Repeater mode data, show fail or success, and user can configure this data in this page if required. Status in Repeater Mode Pls note, when click wireless relay setting, following page will pop up, you can make change from here easy: Wireless Relay Setting All rights reserved Niveo International BV 2020...
Page 11 3. WISP Operation mode: Click WISP operation mode in Wizard, then will pop up the configure page, please set the WISP operation mode based on the steps showed in picture: WISP Mode Configure the right WAN setting in WISP operation mode, then next. All rights reserved Niveo International BV 2020...
Page 13 Then complete and back to status, will show the connection fail or success, then can configure the data based on request: Status in WISP mode Remark: When click WAN Setting, will pop up following picture: WAN setting in WISP mode 4.
Page 15 Status in AP Mode 3) Advanced Setting: In advanced setting, user can check the Outdoor CPE’s firmware version, working status, 2.4G wireless, 5.8G Wireless, LAN Status, upgrade firmware, Reset... Let’s Click Advanced Setting in status page, will show return home, Setup Wizard which we showed before.
Page 17 LAN Status 2.4G Wireless Setting: In this part, will show the 2.4G Basic Setting, Virtual AP, Access control and Advanced Setting: Basic Setting in 2.4G Wireless 2G Wireless Analyzer: Mainly to analyze the AP’s signal strength in some channel, to make user more easy to choose the right channel and avoid the Wi-Fi interface.
Page 18 Wireless Analyzer Virtual AP: There are 3 virtual AP in 2.4G wireless, if need virtual SSID, then users can configure it showed in following picture: Virtual AP All rights reserved Niveo International BV 2020...
Page 19 2.4G Access Control: Mainly show MAC allow or deny: MAC Access Control 2.4G Advanced Settings: In this page, will show the regional, RF Power, Max user access... Advanced Setting All rights reserved Niveo International BV 2020...
Page 20 5.8G Wireless Setting: Almost same as 2.4G Wireless: 5.8G Wireless Setting Network setting: In this page, mainly to show the LAN setting and VLAN as follow: Network Setting All rights reserved Niveo International BV 2020...
Page 21 Tag VLAN Setting Management: In this part, show the system time, Logs, upgrade firmware, system, user info. And we show System time, how to upgrade firmware and system page to users: System Time All rights reserved Niveo International BV 2020...
Page 22 Firmware Upgrade System info Share Internet and Obtain IP address automatically Set computer’s TPC/IP as Obtain an IP address automatically, Obtain DNS server address automatically as following picture showed. The computer will obtain the IP address from router or base station to get Internet. All rights reserved Niveo International BV 2020...
Page 23 Trouble Shooting: F 1 The Failure phenomenon and solution Failure phenomenon Solution Pls check the IP address of computer and Outdoor CPE to see whether they are in same networking segment, The method is click “start”-“Run” input“cmd”，ping 192.168.2.200 to test the Outdoor CPE connectivity. Reset Outdoor CPE and load it again;...

Niveo Professional NWA220 User Manual

Quick Links

Related Manuals for Niveo Professional NWA220

Summary of Contents for Niveo Professional NWA220