Related Manuals for Carson CAMEDIAXBR
Summary of Contents for Carson CAMEDIAXBR
- Page 1 # CAMEDIAXBR (rustic) dpci # 249-10-0807 style # CAMEDIAXWL (walnut) dpci # 249-10-2028 >> assembly instructions © 2019 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
- Page 2 Congratulations on your latest Target purchase. Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you. All you need to do is follow our simple instructions and you’ll be on your way to transforming your room in no time.
- Page 3 table of contents introduction hardware parts list how to use the cam lock system assembly 7-13 QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and dpci number ready when calling.
- Page 4 hardware (H1) x 14 (H2) x 12 (H3) x 14 (H4) x 14 (H5) x 19 wooden dowel flat head screw cam bolt 12mm pan head screw (H6) x 8 (H7) x 1 (H8) x 1 (H9) x 1 (H10) x 1 shelf pin 15mm truss head screw wall strap...
- Page 5 exploded diagram ITEM DESCRIPTION QUANTITY top panel bottom assembly left side assembly right side assembly center assembly adjustable shelf back panel front beam side trim front trim...
- Page 6 how to use the cam lock system Screw cam bolt into panel Align cam bolt(s) with cross-bored Push cam into panel - arrow feature hole(s) and insert all the way until on cam top points to panel edge panel(s) are flush Rotate cam(s) clockwise 180°...
- Page 7 step 1: attach center assembly to bottom assembly front (H1) x 2 (H2) x 2 wooden dowel flat head screw 1.1. Carefully tap small wooden dowels into place in bottom assembly. Leave 1/2” of the dowels sticking out. 1.2. Do not over tighten screws.
- Page 8 step 2: attach front beam and side assemblies (H1) x 6 (H3) x 6 (H4) x 6 wooden dowel cam bolt 2.1. Carefully tap small wooden dowels into place in left side assembly and right side assembly. Leave 1/2” of the dowels sticking out. 2.2.
- Page 9 step 3: attach front and side trim (H2) x 10 flat head screw 1.1. Do not over tighten screws.
- Page 10 step 4: attach top panel front (H1) x 6 (H3) x 8 (H4) x 8 wooden dowel cam bolt 4.1. Carefully tap small wooden dowels into place in top panel. Leave 1/2” of the dowels sticking out. 4.2. Screw-In cam bolts must be screwed down flush in top panel. 4.3.
- Page 11 step 5: attach back panel FAILURE TO FOLLOW ALL DIRECTIONS ON THIS PAGE MAY RESULT IN DOOR NOT SLIDING SMOOTHLY Begin by installing all of the screws along one hole for anti-tip edge of the back panel. Next, using a square or tape measure, make sure that the cabinet is square.
- Page 12 step 6: install adjustable shelves (H6) x 8 shelf pin 6.1. Insert shelf supports into desired hole. Different holes accommodate different shelf heights. 6.2. Angle shelf to fit between the rails and set on top of shelf supports.
- Page 13 step 7: install anti-tip kit (H9) (H9) Position against wall Position against wall (H8) (H8) Mark position of strap hole on wall Mark position of strap hole on wall (H11) (H11) Drill 1/4” hole Drill 1/4” hole (H7) (H7) Tap in wall anchor Tap in wall anchor (H11) (H11)
- Page 14 1. WARNING - Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote control or toys placed on the furnishing may encourage a child to climb on the furnishing and as a result the furnishing may tip over on to the child. 2.
- Page 15 © 2019 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
Need help?
Do you have a question about the CAMEDIAXBR and is the answer not in the manual?
Questions and answers