Denon AVR-X7200W Service Manual page 30

3.5.6. Video system confirmation items
fig. XX: See the block diagram of the fig.XXth.
Paths confirmation item
Analog Video
V 0 1 : V I D E O
fig.17
1
Video Convert
V 0 2 : V . C O N V E R T
(Analog or HDMI ⇒ HDMI) fig.18
2
HDMI pass
V 0 3 : H D M I
（MAIN ZONE） fig.19
3
HDMI CEC
V 0 4 : H D M I
fig.20
4
HDMI Audio
V 0 5 : H . A U D I O - A V R
fig.21a
(Audio : AVR)
fig.21b
5
fig.21c
HDMI Audio
V 0 6 : H . A U D I O - T V
(Audio : TV)
fig.22a
6
fig.22b
GUI
V 0 7 : G U I
fig.23
7
HDMI
V 0 8 : Z O N E 2
(ZONE2) fig.24
8
Display
Input Source : CBL/SAT
P A S S
Video Convert(IP Scaler) : OFF, All sources
MAIN ZONE : ON
ZONE2 : ON
ZONE3 : OFF
Input Source : CBL/SAT
Video Convert(IP Scaler) : ON, All sources
IP Scaler : "Analog & HDMI", All sources
Resolution : "Auto", All sources
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
Input Source : CBL/SAT
P A S S
Source of Video Convert(IP Scaler) : OFF, All sources
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
Input Source : CBL/SAT
C E C
HDMI Control : ON
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
Input Source : CBL/SAT
HDMI Control : OFF
HDMI Audio : AVR ( if checking the audio output from AVR )
Input Source : CBL/SAT
HDMI Control : OFF
HDMI Audio : TV ( if checking the audio output from TV )
Input Source : CBL/SAT
M E N U O N
Video Convert(IP Scaler) : ON, All sources
IP Scaler : "Analog & HDMI", All sources
Resolution : "AUTO", All sources
Setup Menu : ON
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
Input Source : CBL/SAT
H D M I
ZONE2 Source : Source
MAIN ZONE : ON
ZONE2 : ON
ZONE3 : OFF
Settings
・Component input ⇒ Component output
(b The input source can be switched to any source except CBL/SAT.）
・CVBS input ⇒ IP Scaler ⇒ HDMI output.
・Component input ⇒ IP Scaler ⇒ HDMI output.
・HDMI input ⇒ IP Scaler ⇒ HDMI output.
・ETHERNET input ⇒ IP Scaler ⇒ HDMI output.
(b The input source can be switched to any source except CBL/SAT.）
・HDMI input ⇒ HDMI output（MAIN ZONE）
(b The input source can be switched to any source except CBL/SAT.）
・ When the power supply of a TV is put in the standby mode, make sure that the power supply of this unit is also put
in the standby mode.
・The ARC path can also be checked (check this using the TV input source).
(b The input source can be switched to any source except CBL/SAT.）
・HDMI input(PCM , DolbyDigital , DTS) ⇒ Speaker output.
・HDMI input(HD audio) ⇒ Speaker output.
(b The input source can be switched to any source except CBL/SAT.）
・HDMI input(PCM , DolbyDigital , DTS) ⇒ HDMI output (audio output from connected TV)
(b The input source can be switched to any source except CBL/SAT.）
・GUI display ⇒ HDMI output.
(b The input source can be switched to any source except CBL/SAT.）
・HDMI input ⇒ HDMI output (ZONE2)
(b The input source can be switched to any source except CBL/SAT.）
30
Contents of confirmation Remarks