Advertisement
Quick Links
Operating instructions and
specifications for
Squeeze Off Tool
Products by innovation not imitation
Pt
Helping you make the right connections™
Models covered by this manual:
Squeeze 16 20 25 32 SDR 11
Squeeze 16/32 40 50 63 SDR 11
Squeeze 20 25 32 40 50 63 SDR 11
Squeeze 20 25 32 40 50 63 90
SDR11/17
Squeeze 63 90
SDR11/17
110
SDR17
125
SDR17
1
Advertisement
Related Manuals for Caldertech Squeeze 16 20 25 32 SDR 11
Summary of Contents for Caldertech Squeeze 16 20 25 32 SDR 11
- Page 1 Products by innovation not imitation Helping you make the right connections™ Models covered by this manual: Squeeze 16 20 25 32 SDR 11 Squeeze 16/32 40 50 63 SDR 11 Squeeze 20 25 32 40 50 63 SDR 11 Squeeze 20 25 32 40 50 63 90...
- Page 2 INDEX. Specifications ..........4 General description ........5 Safety Precautions ........6 Instructions for use ........7 Certificate of conformity ......9 Certificate of calibration ......10 Warranty information………………………………11...
-
Page 4: Specifications
Finish: Yellow and Silver zinc plated (Steel) Powder coating Dimensions: Squeeze 16 20 25 32 SDR 11 (H x W x D) 210mm x 150mm x 55mm Squeeze 20 25 32 40 50 63 SDR 11 (H x W x D) - Page 5 reserves the right to change the specification of its models at any time, without prior notice. Important! This manual outlines the operation of the electrofusion tooling. This manual forms a part of the product to which it relates. It should be kept for the life of the product. Any amendments issued by Caldervale Technology Ltd should be incorporated in the text.
-
Page 6: Safety Precautions
Safety Precautions 1. This tool is designed to be used in conjunction with best practices as stated in Gas Industry Standard GIS/PL2-7:2006 Squeeze-off equipment. 2. It is imperative that all possible precautions are made to avoid unexpected movement of the tool during use. 3. - Page 7 Instructions for use. Fitting 1. Check Pipe Diameter and SDR ratio. Set both LIMIT PLATES (See Illustration (2) below) to appropriate sizes on all 4 Squeeze-Off Units. The correct orientation is with the required size pointing towards the BOTTOM BAR 2.
- Page 8 Maintenance Clean Threaded ‘T-Bar’ screw threads after use, and re- grease/lubricate at regular intervals (after every use) DO NOT allow dirt, mud or other abrasive material to enter the screw thread! Always wipe-off debris BEFORE tightening/un- tightening threaded ‘T-Bar’. Failure to observe this may affect any warranty claims due to the specific use of this tooling (does not affect statutory rights).
-
Page 9: Ec Declaration Of Conformity
EC DECLARATION OF CONFORMITY MACHINERY SUPPLIER: Caldervale Technology Limited SUPPLIER’S ADDRESS: Bretfield Court, Dewsbury, WF12 9DB, Declares that the Machinery described below: Make: Product: Maxifuse™ Mechanical Squeeze Tools S1 & similar Type: 16 20 25 32 SDR 11, 16/32 40 50 63 SDR 11, 20 25 32 40 50 63 SDR 11, 55 63 75 90 SDR11/17 &... - Page 10 Certificate of calibration. • This product has been inspected and tested in accordance with the ISO9001 quality control systems and procedures in place at Caldervale Technology Ltd, Dewsbury. This product has no calibration period, periodic, safety inspections • should be carried out by the operator if in any doubt please contact the manufacturer for further information Decommissioning &...
- Page 11 Warranty Information. Extent of Warranty. Subject to clauses 2 and 3, Caldervale Technology Ltd warrants to the end-user customer that its products will be free from defects in materials and workmanship, for six months after the date of purchase by the end-user customer, subject to providing proof of purchase. If Caldervale Technology Ltd receives, during the warranty period, notice of a defect in product which is covered by this warranty, Caldervale Technology Ltd shall either repair or replace the product, at...
- Page 12 Limitations of Warranty. Caldervale Technology Ltd does not warrant the operation of any product to be uninterrupted or error free. Caldervale Technology Ltd makes no other warranty of any kind, whether express or implied, with respect to its products. Caldervale Technology Ltd specifically disclaims the implied warranties of satisfactory quality and fitness for a particular purpose.
- Page 13 Please complete this information and keep it safely with your proof of purchase receipt. You will require it for any warranty claim. Where purchased .............. Date of purchase .............. Name & address .............. of purchaser ..............................................................Type of tool ..............
- Page 14 For Service and repair please contact: Caldervale Technology Ltd Bretfield Court Dewsbury West Yorkshire WF12 9DB United Kingdom Tel: +44 (0)1924 469571 Fax: +44 (0)1924 460951 sales@caldertech.com http://www.caldertech.com © 2007 Revision G...
Need help?
Do you have a question about the Squeeze 16 20 25 32 SDR 11 and is the answer not in the manual?
Questions and answers