Enter setup Chapter 1: Factory Defaults Scan "Restore all Factory Defaults" to restore all settings. Barcodes with "*" are the factory default setting. Restore all Factory Defaults Users can set the corresponding requirements, then scan and save the current settings as custom defaults. Save as Custom Defaults Scan “Custom Defaults”...
Enter setup Enter setup Chapter 2: Product Information Chapter 2: Product Information Query firmware version Query firmware version Query manufacturer information Query manufacturer information Query model number Query model number Query products serial number Query products serial number Manufacturer Website Query production batch Query production batch Company Name...
Enter setup Chapter 3: Communication Interface configure the standard keyboard output When connected with USB, scan “USB-KBW” to * USB-KBW When connected with USB, scan “USB-COM” to configure the virtual serial output USB-COM When connected with Serial Line scan “TTL/RS232” to configure serial output, serial port related default configuration is: 9600 bps, 8 bits, no parity bit, one stop bit.
Enter setup Chapter 4: Scan Mode Manual Mode Manual mode-keep button down, press the button to trigger the reading, and release the button to end the reading. If the reading time is successful or the reading time exceeds the single reading time, the reading will end. *Manual mode - Keep button down Manual mode - Button trigger,press the button to trigger to read, release the button but...
Page 11
Enter setup Set reading time 1000 ms Set reading time 2000 ms Set reading time 3000 ms *Set reading time 6000 ms Set reading time 10,000 ms (100 ms ~ 25,500 ms) Set One Reading Time * Only Read One Code Exit setup...
Page 12
Enter setup Enable Batch reading code Max 2 codes Max 5 codes Max 10 codes Max 16 codes * Max 32 codes Set any number Exit setup...
Page 13
Enter setup After jumping from other modes to manual mode, it is allowed to return to the original mode after a period of off time. Read the following setting code to select different delays. The default time is 4000 ms. After off 500 ms to return After off 1000 ms to return After off 2000 ms to return...
Enter setup 2 . Continuous Scanning Mode Continuous Scanning Mode, no manual trigger required. When reading success or after the end of single code reading time,will automatically start the next reading. (Continuous scanning period can switch to manual mode by pressing the button temporary.) Continuous mode *Temporary switching manual mode Do not temporary switching Manual Mode...
Page 15
Enter setup Set reading time 3,000 ms * Set reading time 6,000 ms Set reading time 10,000 ms Set reading time 20,000 ms Set Single Reading Time (100 ms ~ 25,500 ms) Read interval setting The space time between two readings, that is, after the last reading (whether the reading is successful or not), there is no reading within the setting space time, and the next reading is not conducted until the end of the space time.
Page 16
Enter setup Set Space time 100 ms Set Space time 200 ms * Set Space time 500 ms Set Space time 1,000 ms Set Space time 2,000 ms Set Space time (0 ms ~ 4,000 ms) Exit setup...
Page 17
Enter setup The same barcode reading delay time In order to avoid repeated reading of the same barcode, when reading the same barcode again, only when the space time is longer than the delay time, can reading be allowed. Set same code delay time 0 ms Set same code delay time 500 ms *Set same code delay time 1000 ms Set same code delay time 2000 ms...
Page 18
Enter setup Set same code delay time 10,000 ms Set same code delay time (0 ms ~ 10,000 ms) Exit setup...
Enter setup 3 . Automatic Scanning Mode In Automatic Scanning Mode, no manual trigger required,The sensor will automatically detect the surrounding environment. When the scene changes, it will automatically trigger reading. When reading is successful or exceeds one reading time, reading will end.Whether the last reading is successful or not, the detection state will be re-entered.
Page 20
Enter setup The same barcode reading delay time In order to avoid repeated reading of the same barcode, when reading the same barcode again, only when the space time is longer than the delay time, can reading be allowed. Set same code delay time 500 ms * Set same code delay time 1,000 ms Set same code delay time 2,000 ms Set same code delay time 3,000 ms...
Page 21
Enter setup Image time Stable time before entering the detection environment. Set Image time 100 ms Set Image time 200 ms Set Image time 500 ms *Set Image time 1,000 ms Set Image time (100 ms ~ 3,000 ms) Exit setup...
Page 22
Enter setup Sensitivity Detects the degree of change in the scene. * High Sensitivity Medium Sensitivity Low Sensitivity Set Single Reading Time In Automatic Scanning Mode, the maximum amount of time that continuous recognition is allowed before successful reading. Set reading time 1,000 ms *Set reading time 2,000 ms Set reading time 3,000 ms Set reading time 5,000 ms...
Page 23
Enter setup Set reading time 10,000 ms Set reading time 20,000 ms Set reading time (100 ms ~ 25,500 ms) Exit setup...
Enter setup Chapter 5: Illumination and Aiming 1. Illumination Illuminating light provide illumination aids for reading, improve reading performance and adaptability to weak ambient light. *Reading On 2. Aiming Aiming light can help users find the best reading area while reading. *Reading On Exit setup...
Enter setup Charpter 6: Output Remind The indicator does not flash * The indicator flash 1 time The indicator flash 2 times The indicator flash 3 times The indicator flash 4 times The indicator continue time 100 ms Exit setup...
Page 26
Enter setup The indicator continue time 200 ms The indicator continue time 500 ms The indicator continue time 1000 ms The indicator continue time 1500 ms The indicator continue time 2000 ms The indicator interval time 100 ms The indicator interval time 200 ms Exit setup...
Enter setup 2. Reading Sound ( 1 ) All indicator Disable power on sound * Enable power on sound Disable setting code sound * Enable setting code sound Exit setup...
Enter setup Sound remind 2 times Set sound remind times(1~5) ( 3 ) Sound frequency Set sound frequency 1600 Hz *Set sound frequency 2700 Hz Set sound frequency 3200 Hz Set sound frequency 4200 Hz Exit setup...
Enter setup Set sound frequency (100 ~ 20,000 Hz) ( 4 ) Read sound time Set sound time 50 ms * Set sound time 100 ms Set sound time 150 ms Set sound time 200 ms Set sound time 250 ms Exit setup...
Enter setup Set sound time 300 ms 3 . Decode status remind Enable NG (No Read) *Disable NG (No Read) Set No Read information (1-16 bytes) Exit setup...
Enter setup Italian 14 5 . Set Virtual Keyboard Output characters ALT+numeric keys * Output characters using a large keyboard Use "Ctrl" to combine output control characters *Original output control character Enable small keypad * Disable small keypad Exit setup...
Enter setup 6 . Case conversion * No case conversion Conver all to upper case Convert all to lower case Letter case exchange Using shift to unblock uppercase locking Using capslock to unblock uppercase locking Exit setup...
Enter setup 7 . Data encoding format To enable the host to print Chinese data in the specified encoding format, you can set it by reading "data encoding format". GBK format, suitable for notepad, Excel and other software. Unicode, suitable for Word and other software.
Enter setup Charpter 7: Data editing 1. Data editing *Enable data editing Disable data editing 2 . Symbol name display Enable symbol name display Disable symbol name display 3 . Symbol length display Enable symbol length output Exit setup...
Enter setup Disable Symbol length output 4 . CODE ID Users can identify different barcode types by Code ID. The corresponding Code ID of each barcode type can be modified by themselves (the corresponding setting Code can be found in the enable/disable configuration of barcode type). Code ID uses one character to identify , see appendix 3.
Enter setup * Disable AIM ID output 5 . Terminal Charater *Enable terminal charater Disable terminal charater Do not add terminal character Set terminal CR Set terminal CR+LF Exit setup...
Enter setup Set Terminal TAB Set Terminal CR+CR Set Terminal CR+LF+CR+LF Set Terminator Character (1-8 bytes) 6 . Prefix/Suffix Setting Prefix/suffix is a user-defined modified charater string before or after decoding information, which can be added by scanning "Enable prefix" or "Enable suffix" setting code. Set prefix/suffix, scan setting codes of "set prefix"...
Page 44
Enter setup *Disable Prefix Set Prefix (1~16 bytes) *Disable Suffix Enable Suffix Set Suffix (1~16 bytes) Exit setup...
Enter setup EAN-8 * Enable EAN-8 Disable EAN-8 Do not transmit code 11 check character * Transmit Code 11 check character Set No.1 code ID Set No. 2 code ID Exit setup...
Page 47
Enter setup Convert EAN-8 to EAN-13 Do not convert EAN-8 to EAN-13 Enable 2-digit add-on code Disable 2-digit add-on code Enable 5-digit add on code Disable 5-digit add-on code Equire add-on code Exit setup...
Enter setup Do not require add-on code Add delimiter before the add-on code Do not delimiter EAN-13 Enable EAN-13 Disable EAN-13 Do not transmit check character after verification Exit setup...
Page 49
Enter setup Transmit check character after verification On ISBN/ISSN translation Off ISBN/ISSN translation 10 Digit ISBN 13 Digit ISBN Set No. 1 code ID Set No. 2 code ID Exit setup...
Enter setup UPC-E * Enable UPC-E Disable UPC-E Do Not Transmit Code 11 Check Character * Transmit code 11 check character Enable UPC-E1 * UPC-E1: Disable UPC-E1 Set No. 1 code ID Exit setup...
Page 53
Enter setup Set No.2 Code ID Enable 2-Digit Add on code Disable 2-Digit Add-On Code Enable 5-Digit Add On Code Disable 5-Digit Add-On Code Equire Add-On Code Do Not Require Add-On Code Exit setup...
Page 54
Enter setup Add Delimiter before the Add-on Code Do not Delimiter Add US country Code 0 Do Not add Country code System Character Do Not system Character Convert UPC-E1 to UPC-A Exit setup...
Enter setup UPC-A Do not convert UPC-A *Enable UPC-A Disable UPC-A Do not transmit check character after verification Transmit check character after verification Enable 2-Digit add-on code Exit setup...
Page 56
Enter setup Disable 2-digit add-on code Enable 5-digit add-on code Disable 5-digit add-on code Equire add-on code Do not require add-on code Add delimiter before the add-on code Do not delimiter Exit setup...
Page 57
Enter setup Set No.1 code ID Set No. 2 code ID Add US country code 0 Do Not add country code System character Do not system character Exit setup...
Enter setup Interleaved 2 of 5 *Enable Interleaved 2 of 5 Disable interleaved 2 of 5 Set the minimum length Set the maximum length Set No. 1 code ID Set No. 2 code ID *Disable Exit setup...
Page 63
Enter setup Do not transmit check character after verification Transmit check character after verification Exit setup...
Enter setup China Post 2 of 5 Transmit check character after verification *Disable code 2 of 5 China Post Set the minimum length Set the maximum length Set No. 1 code ID Set No. 2 Code ID * Disable Exit setup...
Page 65
Enter setup Do not transmit check character after verification Transmit check character after verification Exit setup...
Enter setup Matrix 2 of 5 Enable Matrix 2 of 5 Disable Matrix 2 of 5 Set the minimum length Set the maximum length Set No.1 code ID Set No. 2 code ID * Disable Exit setup...
Page 67
Enter setup Do not transmit check character after verification Transmit check character after verification Exit setup...
Enter setup Industrial 2 of 5 Enable code 2 of 5 industrial Disable code 2 of 5 industrial Set the minimum length Set the maximum length Set No. 1 code ID Set No. 2 code ID * Disable Exit setup...
Page 69
Enter setup Do not transmit check character after verification Transmit check character after verification Exit setup...
Enter setup IATA 2 of 5 Enable code 2 of 5 IATA *Disable code 2 of 5 IATA Set the minimum length Set the maximum length Set No. 1 code ID Set No. 2 code ID * Disable Exit setup...
Page 71
Enter setup Do not transmit check character after verification Transmit check character after verification Exit setup...
Enter setup ITF-14 Enable ITF-14 * Disable ITF-14 Do Not Transmit Check Character After Verification Transmit check character after verification Set No.1 code ID Set No. 2 code ID Exit setup...
Page 73
Enter setup DP-12 Enable DP-12 * Disable DP-12 Do not transmit check character after verification Transmit check character after verification Set No. 1 code ID Set No. 2 code ID Exit setup...
Enter setup DP-14 Enable DP-14 * Disable DP-14 Do not transmit check character after verification Transmit check character after verification Set No.1 code ID Set No. 2 code ID Exit setup...
Enter setup Enable MSI * Disable MSI Set the minimum length Set the maximum length Set No. 1 code ID Set No. 2 code ID Exit setup...
Page 76
Enter setup Check Character Verification *One check character, no output One check character input Two check characters, MOD10/MOD10 no output Two check characters, MOD10/MOD10 input Two check characters, MOD10/MOD11 no output Two check characters, MOD10/MOD11 input Disable Exit setup...
Enter setup Code 11 Enable code 11 * Disable code 11 Do not transmit check character after verification Transmit check character after verification Set the minimum length Set the maximum length Set No.1 Code ID Exit setup...
Enter setup Set No. 2 code ID Code 39 *Enable code 39 Disable code 39 Transmit start / stop character Do not Transmit start / stop character Enable code 39 full ASCII Exit setup...
Page 79
Enter setup Disable code 39 full ASCI Set the minimum length Set the maximum length * Disable Do not transmit check character after verification Transmit check character after verification Set No. 1 code ID Exit setup...
Enter setup Codabar *Enable Codabar Disable Codabar Set the minimum length Set the maximum length Transmit start / stop character Do Not Transmit start / stop character Exit setup...
Page 83
Enter setup Set No.1 code ID Set No. 2 code ID Check character verification * Disable Do not transmit check character after verification Transmit check character after verification Exit setup...
Page 84
Enter setup Start/Stop Character * ABCD/ABCD ABCD/TN*E abcd/abcd abcd/tn*e Exit setup...
Enter setup Plessey Enable Plessey * Disable Plessey Set the minimum length Set the maximum length Set No. 1 code ID Set No. 1 code ID * Disable Exit setup...
Enter setup Do not transmit check character after verification Transmit check character after verificatio RSS-14 * Enable RSS-14 Disable RSS-14 * Transmit application identifier “01” Do not transmit application identifier Exit setup...
Enter setup Set No.1 code ID Set No. 2 code ID RSS-Limited *Enable RSS-limited Disable RSS-limited * Transmit application identifier “01” Do not transmit application identifier Exit setup...
Enter setup QR Code * Enable QR code Disable QR code Set the minimum length Set the maximum length *Allowable structural connection Do not allowable structural connection *Read mirror symbol Exit setup...
Page 91
Enter setup Do not read mirror symbol Set No.1 code ID 、 Set No.2 code ID Enable OR code *Disable QR code Exit setup...
Enter setup Enter setup Enter setup Data Matrix Do not read mirror symbol Do not read mirror symbol *Enable data matrix Set No.1 code ID Set No.1 code ID 、 、 Disable data matrix Set No.2 code ID Set No.2 code ID Set the minimum length Enable OR code Enable OR code...
Page 93
Enter setup Disable inverse code *Read mirror symbol Do not read mirror symbol *Allowable structural connection Do not allowable structural connection Set No. 1 code ID Set No. 2 code ID Exit setup...
Enter setup Enter setup Appendix 1 Digit Barcodes Maxicode Enable maxicode *Disable maxicode Set the minimum length Set the maximum length Set No. 1 code ID save cancel Set No. 2 code ID reset Exit setup Exit setup...
Enter setup Enter setup Appendix 2 ASCII Table Appendix 2 ASCII Table Scanning value Keyboard value Scanning value Keyboard value Scanning value Keyboard value Keyboard value Keyboard value Scanning Scanning Scanning Scanning Keyboard Keyboard Keyboard Keyboard Scanning Scanning 1000 Null 1043 1086 value...
Enter setup Enter setup Enter setup Appendix 2 ASCII Table Appendix 2 ASCII Table ASCII Table 3 Defaults Table Appendix 3 Factory Defaults Table Symbol type Keyboard value Keyboard value Code ID Character Decimal value Hexadecimal value Scanning Scanning Scanning Scanning Keyboard Keyboard...
Need help?
Do you have a question about the S-52 and is the answer not in the manual?
Questions and answers