Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Splash Lab TSL.R.020 Series
Summary of Contents for Splash Lab TSL.R.020 Series
- Page 1 TSL.R.020 Sensor Faucet...
- Page 2 contents Safety and Warnings Box Contents Technical Data Before You Install How to Install The Complete System Resetting the Sensor Maintenance Cleaning Spare Parts Product Identification Troubleshooting Warranty Contact Details TSL.R.020 RIBBON SENSOR FAUCET MANUAL...
- Page 3 TSL.R.020 ribbon sensor faucet Read and save these instructions WARNING To reduce the risk of fire, electric shock or injury to persons, observe the following: Use this unit in the manner intended by the manufacturer. If you have questions, contact the manufacturer This equipment should be installed in a way that ensures all electrical parts are kept dry.
-
Page 4: Box Contents
box contents Ribbon sensor faucet head Mains power supply Battery supply Anti-rotation plate #1 Counter top gasket Anti-rotation plate #2 Fixing nut Solenoid and cable Flow restrictor TSL.R.020 RIBBON SENSOR FAUCET MANUAL... -
Page 5: Technical Data
technical data Finishes TSL.R.020.C.ELE Bright Polished Stainless steel TSL.R.020.CS.ELE Brushed Stainless steel TSL.R.020.CP.ELE Brushed Copper TSL.R.020.BK.ELE Brushed Black TSL.R.020.BR.ELE Brushed Brass TSL.R.020.BZ.ELE Brushed Bronze TSL.R.020.C.BAT Bright Polished Stainless steel TSL.R.020.CS.BAT Brushed Stainless steel TSL.R.020.CP.BAT Brushed Copper TSL.R.020.BK.BAT Brushed Black TSL.R.020.BR.BAT Brushed Brass TSL.R.020.BZ.BAT Brushed Bronze... - Page 6 technical data FRONT SIDE 7-5/16" 2-1/8" 4-31/32" Default S ensor Range 4-3/4" Ø 1-11/32" Through Hole 3/8" MIN 1-3/8" MAX 2-23/32" Ø 1-1/4" MAX Length 11-13/16" 6" 1/2" BS P Battery Power S upply Mains Power S upply TSL.R.020 RIBBON SENSOR FAUCET MANUAL...
-
Page 7: Before You Install
Sinks Use of a The Splash Lab sink is recommended when used in conjunction with any of the The Splash Lab Ribbon taps. When using other sinks, ensure that holes and appropriate mounting points are created in accordance with the diagram below. -
Page 8: How To Install
how to install Ensure internal anti-rotation ring (D) and Position tap on sink deck through a the gasket (E) are fitted into the recesses Ø 1 1/4” hole and ensure the tap is angled in the Ribbon sensor tap head (A). These pointing in the required direction. - Page 9 This tap can be fitted to a variety of sink types: The Splash Lab Approved Sink a. When using an approved The Splash Lab Ribbon sink, there will be a recess available for the under-sink anti- rotation plate (F). No fixings are required at this stage.
- Page 10 how to install Attach the Ribbon fixing nut (G) with the flat surface towards the sink. We recommend tightening to 15-20 Nm, however this is subject to the sink material and install situation. Fit the end of the flexi-hose onto the outlet of the solenoid, ensuring that the flow restrictor is in place, between the fixing nut and the solenoid valve.
- Page 11 the complete system Water Aerator Ribbon sensor faucet head Mains power supply Battery supply Solenoid and cable Flow restrictor Mains Water Supply Flexi-Hose 110-240 Volt Mains Supply TSL.R.020 RIBBON SENSOR FAUCET MANUAL...
-
Page 12: Resetting The Sensor
resetting the sensor Firstly disconnect the Ribbon Tap head Look under the tap at the sensor near from the Power unit. Wait a minimum of 4 the nozzle. You should see a flashing red seconds and reconnect the power. light. When you see the light position your hand within 2”... - Page 13 When the light stops flashing move your When the light goes out the new hand down to the desired activation detection distance is set. Test the system position and hold. and repeat from step 1 until the tap works as required. *Remove reflective clothing during installation TSL.R.020 RIBBON SENSOR FAUCET MANUAL...
-
Page 14: Maintenance
The Ribbon system has been developed to accommodate for this maintenance yet all work should be done by a trained member of an approved maintenance team. For more information, contact The Splash Lab. cleaning External parts should be cleaned with a soft cloth and a mild solution of soapy water as part of the regular cleaning regime. -
Page 15: Spare Parts
Should a replacement mains power supply be required it is imperative that an identical type is used. Contact The Splash Lab for further information. product identification A unique product identification code can be found on the product tag attached to the water hose. -
Page 16: Troubleshooting
Check that transformer is operating and supplying 6 volts Replace battery on battery powered versions Sensor range is incorrect Adjust sensor settings (see page 10 and 11, or contact The Splash Lab to purchase remote controller Water does not flow / Valve can be heard to open... -
Page 17: Warranty
Sensor taps 2 years’ parts & labour If a defect is found in normal use, The Splash Lab will, at their discretion, repair, provide a replacement part or product, or make appropriate adjustments. Damage caused by accident, misuse, or abuse is not covered by this warranty. Improper care and cleaning will void the warranty. - Page 18 contact General information +1 310 410 5008 5450 W 83rd St, Los Angeles CA90045 500 7th Ave, New York NY10018 Technical support technical@thesplashlab.com For further contact information visit: www.thesplashlab.com TSL.R.020 RIBBON SENSOR FAUCET MANUAL...
- Page 19 TSL.R.020 RIBBON SENSOR FAUCET MANUAL...
Need help?
Do you have a question about the TSL.R.020 Series and is the answer not in the manual?
Questions and answers