Advertisement
Drain
L1
Dispenser (Detergent and Rinse Aid)
Diverter Valve
Diverter Motor
L1
Use top hole of jumper
W2 as test point for F9.
N.O.
BK
P4-2
K2
Pilot L1 Relay
Fuse
(Also see Door
F9
Switch Circuit)
Electronic Control
No test pad on P7-4.
Recommend using test pad on P10-1.
Water Softener
Regeneration Valve
L1
Use top hole of jumper
W2 as test point for F9.
N.O.
BK
P4-2
K2
Pilot L1 Relay
(Also see Door
Switch Circuit)
Electronic Control
Recommend using test pad on P10-1.
Drying
For Heated Dry, heater is also running. See "Heater" circuit under "Water Heating/Heat Dry and Water Sensing with O.W.I. Sensor (Water/Air/Soil/Temperature)."
Vent
Use top hole of jumper
L1
W2 as test point for F9.
N.O.
BK
P4-2
K2
Pilot L1 Relay
Fuse
(Also see Door
F9
Switch Circuit)
Electronic Control
AC Fan (not on all models)
Use top hole of jumper
W2 as test point for F9.
N.O.
BK
P4-2
K2
Pilot L1 Relay
(Also see Door
Switch Circuit)
Electronic Control
Recommend using test pad on P10-1.
Electronic Control
L1
Use top hole of jumper
W2 as test point for F9.
N.O.
BK
P4-2
K2
Pilot L1 Relay
(also see Door
Switch Circuit)
Test pad on P9-3 might crowd P9-1
Recommend using test pad on P10-1.
BU
BU
P7-6
P7-4
Pin 3
Pin 1
P10-1
Diverter Motor
Ω
Ω
1,100
- 1,400
120V, 60 Hz, 3W
V
P7-3
Pin 1
Regeneration Valve
Fuse
P10-1
F9
890Ω - 1,090Ω
120V, 60 Hz, 6W
No test pad on P7-3.
(Red stripe
(Red stripe
on plug)
on plug)
BR
BR
P10-1
P10-3
Pin 1
Pin 5
Vent Wax Motor
600Ω - 1,800Ω
120V, 60 Hz, 6W
Electronic Control
Electronic Control
L1
N.O.
BK
P4-2
K2
Pilot L1 Relay
(Also see Door
Switch Circuit)
No test pad on P7-3.
Recommend using test pad on P10-1.
BR
P6-3
Pin 1
Fuse
P10-1
F9
Drain Motor
15Ω - 60Ω
120V, 60 Hz, 60W
No test pad on P6-3.
Dispenser Wax Motor
1.4KΩ - 3.0KΩ
120V, 60 Hz, 10W
Pin 1
VI
P9-3
Pin 1
Fuse
Dispenser Solenoid
P10-1
F9
260Ω - 300Ω
120V, 60Hz, 17W
Diverter Sensor
N
Sensor
Input
WH
P4-1
Triac
Electronic Control
Electronic
Control
Switch closes momentarily
and then reopens as the diverter
reaches each potential diverter position.
N
V
WH
P4-1
P7-1
Pin 3
Triac
Electronic
Control
Fan
N
P10-5
WH
P4-1
DC Ref
Electronic Control
BU
P7-3
Pin 1
Fuse
P10-1
F9
Fan Motor
Ω -
60
120 V, 60 Hz, 12 Watts
5
BR
WH
P4-1
P6-1
Pin 3
Triac
Electronic Control
N
Pin 5
WH
VI
P4-1
P9-1
Pin 3
Triac
Electronic Control
N.O.
P11-4
P11-3
Diverter
Position
Switch
Salt Level Sensing
(Closed when salt low)
Salt Level Reed Switch
RD
5V
P11-2
Pin 1
N.O.
39 KΩ
Pin 4
(RD)
Pin 1
Electronic Control
N.O.
(Optional Flowmeter)
(Red stripe
on plug)
_
+
BR
BR
Pin 1
Pin 3
Fan Motor
31KΩ - 41KΩ
5 VDC, 1W
Must measure resistance
with correct polarity and
disconnected from controls.
Electronic Control
BU
P4-1
P7-1
Pin 3
Triac
Ω
80
N
5V
P11-2
Electronic Control
No test pad on P11-3.
Recommend using test pad on P11-2.
Sensor
RD
P11-1
Input
Pin 2
Pin 3
(RD)
Pin 3
Electronic
Control
(Red stripe
on plug)
P10-4
5V
P11-5
Electronic Control
No test pad on P10-4.
Recommend using test pad on P11-5.
N
WH
Advertisement
