All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by EL 0867 BU TV Consumer Care...
: 1366 × 768 : 90% R.H. Min. light output (cd/m : 500 Min. contrast ratio : 55000:1 Power consumption (values are indicative) (32PFL9603D/10) : ≈139/140 (32") - Normal operation (W) : 33000:1 : ≈186 (37") (32PFL7623D/10) : ≈110/248 (42") : 30000:1 (37", 42"...
Page 3
Technical Specifications, Connections, and Chassis Overview Q529.1E LA EN 3 Connections USB2.0 E_06532_022.eps 300904 Figure 1-2 USB (type A) - +5V - Data (-) - Data (+) - Ground HDMI: Digital Video, Digital Audio - In E_06532_017.eps 250505 Figure 1-3 HDMI (type A) connector - D2+ Data channel - Shield...
Page 4
EN 4 Q529.1E LA Technical Specifications, Connections, and Chassis Overview 1.2.2 Rear Connections 12 - n.c. 13 - Ground Red 14 - Ground Data Service Connector (UART) / 75 Ω 15 - Video Red 0.7 V - Ground 16 - Status/FBL 0 - 0.4 V: INT - UART_TX Transmit...
Page 5
Technical Specifications, Connections, and Chassis Overview Q529.1E LA EN 5 HDMI 1, 2 & 3 Digital Video, Digital Audio - In - D0- Data channel 10 - CLK+ Data channel 11 - Shield 12 - CLK- Data channel E_06532_017.eps 13 - Easylink Control channel 250505 14 - n.c.
• Be careful during measurements in the high voltage • Use only lead-free soldering tin Philips SAC305 with order section. code 0622 149 00106. If lead-free solder paste is required, • Never replace modules or other components while the unit please contact the manufacturer of your soldering is switched “on”.
TV set, it is best to test the high voltage insulation. production year, and digits 7 and 8 refer to production week (in It is easy to do, and is a good service precaution. 3. Directions for Use You can download this information from the following websites: http://www.philips.com/support http://www.p4c.philips.com...
EN 8 Q529.1E LA Mechanical Instructions 4. Mechanical Instructions Index of this chapter: 4.1 Cable Dressing 4.2 Service Positions Notes: 4.3 Assy/Panel Removal VE8 Styling • Figures below can deviate slightly from the actual situation, 4.4 Assy/Panel Removal ME8+ Styling due to the different set executions.
Page 9
Mechanical Instructions Q529.1E LA EN 9 Service Positions For easy servicing of this set, there are a few possibilities created: • The buffers from the packaging (see figure “Rear cover”). • Foam bars (created for Service). 4.2.1 Foam Bars Required for sets 42"...
Page 10
EN 10 Q529.1E LA Mechanical Instructions Assy/Panel Removal VE8 Styling 1. Remove the mushrooms [1]. 2. Remove the fixation screws [2] from the hatch and lift the hatch from the rear cover. 4.3.1 Rear Cover 3. Unplug the connectors [3]. 4.
Page 11
Mechanical Instructions Q529.1E LA EN 11 4.3.2 Ambilight 4.3.3 Key Board Refer to next figure for details. Refer to next figure for details. 1. Release the wire from the wire guides [1]. 1. Unplug the key board connector [1] from the IR & LED 2.
Page 12
EN 12 Q529.1E LA Mechanical Instructions 4.3.4 Bass-midrange Speakers 4.3.6 Display Supply Panel Refer to next figure for details. Refer to next figure for details. 1. Release the speaker connectors [1] from unit. 1. Unplug the connectors [1]. 2. Remove the screw [1] and lift the whole unit from the set. 2.
Page 13
Mechanical Instructions Q529.1E LA EN 13 4.3.8 LCD Panel Refer to next figure for details. 1. Remove the SSB as described earlier. 2. Remove the Bass-midrange speakers as described earlier. 3. Remove the Tweeters as described earlier. 4. Unplug the connectors [1]. 5.
EN 14 Q529.1E LA Service Modes, Error Codes, and Fault Finding 5. Service Modes, Error Codes, and Fault Finding Index of this chapter: – Skip/blank of non-favourite pre-sets. 5.1 Test Points 5.2 Service Modes How to Activate SDM 5.3 Stepwise Start-up For this chassis there are two kinds of SDM: an analog SDM 5.4 Service Tools and a digital SDM.
Page 15
• B= the region: A= AP, E= EU, L= LatAm, U = US. For AP sets it is possible that the Europe software 39mm version is used. PHILIPS MODEL: • X.Y.W.Z= the software version, where X is the 32PF9968/10 PROD.SERIAL NO:...
Page 16
EN 16 Q529.1E LA Service Modes, Error Codes, and Fault Finding • Switch the set to STAND-BY via the RC-transmitter. • 12NC SSB. Gives an identification of the SSB as stored in NVM. Note that if an NVM is replaced or is initialized after corruption, this identification number has to be re-written to 5.2.3 Customer Service Mode (CSM)
Page 17
Service Modes, Error Codes, and Fault Finding Q529.1E LA EN 17 Stepwise Start-up mode with a faulty FET 7U08 is done, you can destroy all IC’s supplied by the +3V3, due to overvoltage (12V on 3V3-line). It is recommended to measure first the FET 7U08 or others When the TV is in a protection state due to an error detected by FET’s on shortcircuit before activating SDM via the service stand-by software (error blinking is displayed) and SDM is...
Page 18
EN 18 Q529.1E LA Service Modes, Error Codes, and Fault Finding Stand by or Mains is applied Protection Standby Supply starts running. All standby supply voltages become available . st-by µP resets Initialise I/O pins of the st-by µP: If the protection state was left by short circuiting the - Switch reset-AVC LOW (reset state) SDM pins, detection of a protection condition during - Switch WP-NandFlash LOW (protected)
Page 19
Service Modes, Error Codes, and Fault Finding Q529.1E LA EN 19 From I_17660_125a.eps From I_17660_125a.eps Reset-system is switched HIGH by the Reset-system is switched HIGH by the Release reset MPEG4 module: AVC at the end of the bootscript AVC at the end of the bootscript BOLT-ON-IO: High Reset-system is connected to USB -reset,...
Page 20
EN 20 Q529.1E LA Service Modes, Error Codes, and Fault Finding Constraints taken into account: - Display may only be started when valid LVDS output clock can be delivered by the AVC . - Between 5 and 50 ms after power is supplied, display should receive valid lvds clock . action holder: AVC - minimum wait time to switch on the lamp after power up is 200ms.
Page 21
Service Modes, Error Codes, and Fault Finding Q529.1E LA EN 21 Constraints taken into account: - Display may only be started when valid LVDS output clock can be delivered by the AVC . - Between 5 and 50 ms after power is supplied, display should receive valid lvds clock . action holder: AVC - minimum wait time to switch on the lamp after power up is 200ms.
Page 22
EN 22 Q529.1E LA Service Modes, Error Codes, and Fault Finding action holder: AVC Constraints taken into account: - Display may only be started when valid LVDS output clock can be delivered by the AVC . action holder : St-by - Between 5 and 50 ms after power is supplied, display should receive valid lvds clock .
Page 23
Service Modes, Error Codes, and Fault Finding Q529.1E LA EN 23 action holder: AVC Active action holder: St-by autonomous action Mute all sound outputs via softmute Wait 100ms Set main amplifier mute (I/O: audio-mute) Force ext audio outputs to ground (I/O: audio reset) And wait 5ms switch off Ambilight...
Page 24
EN 24 Q529.1E LA Service Modes, Error Codes, and Fault Finding Semi Stand by action holder: MIPS action holder: St-by autonomous action If ambientlight functionality was used in semi -standby (lampadaire mode), switch off ambient light *) If this is not performed and the set is Delay transition until ramping down of ambient light is switched to standby when the switch off of finished.
Page 25
4. ComPair features TV software up possibilities. Introduction Specifications ComPair (Computer Aided Repair) is a Service tool for Philips ComPair consists of a Windows based fault finding program Consumer Electronics products. and offers the following: and an interface box between PC and the (defective) product.
Page 26
– “TESTSCRIPT Q529” (3104 337 05021). Downloadable • In CSM mode from the Philips Service website from the section “Software – When entering CSM: error LAYER 1 will be displayed for Service only”. by blinking LED. Only the latest error is shown.
Page 27
Service Modes, Error Codes, and Fault Finding Q529.1E LA EN 27 • Errors detected by main software (MIPS). In this case the error will be logged into the error buffer and can be read out via ComPair, via blinking LED method LAYER error 1- 2, or in case picture is visible, via SAM.
Page 28
EN 28 Q529.1E LA Service Modes, Error Codes, and Fault Finding Table 5-2 Error code overview Monitored Error/ Error Buffer/ Description Layer 1 Layer 2 Prot Blinking LED Device Defective Board MIPS BL / EB SCL/D-SSB MIPS BL / EB SCL/D-DISP Display (LED back light only) PNX doesn’t boot (HW cause) 2...
Page 29
Service Modes, Error Codes, and Fault Finding Q529.1E LA EN 29 • Error 37 (Channel decoder DVBT). When there is no I communication towards the DVBT channel decoder after Example: Error 12 8 6 0 0. start up, LAYER error 2 = 37 will be logged and displayed After activation of the SDM, the front LED will show: via the blinking LED procedure if SDM is switched on.
Page 30
EN 30 Q529.1E LA Service Modes, Error Codes, and Fault Finding monitors do not respond in a defined way, this indicates a 5.8.4 DC/DC Converter malfunction of the system and leads to a protection. As the observers are only used during start-up, they are described in Introduction the start-up flow in detail (see section “5.3 Stepwise Start-up”).
Page 31
Service Modes, Error Codes, and Fault Finding Q529.1E LA EN 31 5.8.5 Exit “Factory Mode” integrated in the RGB signal. So when TXT signal is available but no UI, check the PCI bus. When an “F” is displayed in the screen's right corner, this means that the set is in “Factory”...
Page 32
EN 32 Q529.1E LA Service Modes, Error Codes, and Fault Finding 5.8.14 SSB Replacement Follow the instructions in the flowchart in case a SSB has to be exchanged. See figure “SSB replacement flowchart”. START Set is still operating? Activate SAM and save the TV settings via “Upload to USB”...
Page 33
1. Disconnect the TV from the Mains/AC Power. – For HDMI 2 NVM, use “*port 2*.bin” 2. Press the “OK” button on a Philips TV remote control or a – For HDMI 3 NVM, use “*port 3*.bin” Philips DVD RC-6 remote control (it is also possible to use –...
Page 34
EN 34 Q529.1E LA Service Modes, Error Codes, and Fault Finding • 2.3 MOP_RXSXX_x.x.x.x.zip. A separate MOP Ambient Explanation of the sections Light FPGA SW. This SW is not part of the FUS The flash of TV520 sets consists of a boot-block (block 0), a autorun.upg! A programmed MOP device can also be number of BFFS (Boot Flash File System) partitions, one ordered via the regional Service organization.
Page 35
Service Modes, Error Codes, and Fault Finding Q529.1E LA EN 35 _____> µ µ BTM startup UªUretail Jan 16 2008 12:03:04 Boot deviceST NAND512W3A BFFS init Searching BootLoader.tdfLoad /bffs0/BootLoader.tdf- Done _____> Bootloader startup Start /bffs0/BootLoader.tdf JBL (boottime improvement BootLoader OS_R0.7.2assert Feb 25 2008 12:49:28Searching boot.bat Execute /bffs2/boot.bat from label [4] _____>...
Page 36
EN 36 Q529.1E LA Service Modes, Error Codes, and Fault Finding UªUretail Jan 16 2008 12:03:04 Boot deviceST NAND512W3A BFFS init Searching BootLoader.tdfLoad /bffs0/BootLoader.tdf- Done Start /bffs0/BootLoader.tdf JBL (boottime improvement BootLoader OS_R0.7.2assert Feb 25 2008 12:49:28Searching boot.bat Execute /bffs2/boot.bat from label [6] unknown command, line 302 Execute /bffs1/boot.bat from label [6] * boot1: SR6->USB SW DL boot1...
Page 38
EN 38 Q529.1E LA Service Modes, Error Codes, and Fault Finding 00 003.082 RO Flash file not found in /mnt/jffs0/ro/tvplf/tv520avi/cabinet3 00 003.082 Local flash file not found in file/cabinet3 00 003.082 RU Flash file found in /mnt/jffs0/rupg/tvplf/tv520avi/cabinet 00 003.082 Cabinet flash file : Layout version = 4 ; Content version = 16 00 003.082 Cabinet flash file : Project Id = 0 ;...
Page 39
01 007.979 FLASH system, mount request for partition 2 accepted 00 008.331 Timeout on mountcheck 01 008.692 svspow_m.c:4760::flashopN_OnPartitionMounted::partitionid:2 00 008.769 cetvbend_mpowon: cetvambi_ambilight_Disable 00 009.002 argv[0] is /philips/bin/networkhelper 00 009.002 udhcpc gave me deconfig 00 009.002 HandleUdhcpcNotif : msgq is 32769 01 009.155 svspow_m.c:4772::Sent flashopN_OnPartitionMounted::MOUNT_ON_EVENT 01 009.158 svspow_m.c:1872::gfx setpower ON...
Page 40
-1 010.649 Relayout of window 4 -1 010.657 AppMan: Switch focus to 0x5132d600 [4] 00 010.702 (!!!) *** WARNING [color keying does not work on UPPER layer] *** [Philips/DirectFB/systems/cetvfb/primary.c:202 in get_color_minmax()] 01 010.868 svspow_m.c:3479::apps powntf received for ON -1 010.881 AppMan: Window added (0,0-720x576) [5] - 0! 01 010.897 Surface 1, PlaneId 0 in AttachSurface...
Page 41
Service Modes, Error Codes, and Fault Finding Q529.1E LA EN 41 03 015.788 Census Found device uuid: c7a4be7e-547d-11dc-8034-cc1538aeec30 03 015.792 DeviceType: schemas-upnp-org:device:MediaServer:1 -1 016.098 AppMan: Window config - unhiding window -1 016.098 Relayout of window 5 00 017.948 ***GVC: T2 - ceisusb_m.c (951): "usbdevspN_OnDeviceError( DeviceUnknownAttachedError, -1 )" notification given 00 018.154 ***GVC: T2 - ceisusb_m.c (951): "usbdevspN_OnDeviceError( DeviceUnknownAttachedError, -1 )"...
Page 42
EN 42 Q529.1E LA Service Modes, Error Codes, and Fault Finding 13:51:07 Tv520_Eu_0.61_prod <--- Upgrade now 13:51:11 13:51:11 13:51:11 Software is equal or older, 13:51:11 - press OK to stop 13:51:11 - press down + OK to continue 13:51:11 13:51:12 L: 13% 13:51:15 L: 94% 13:51:16 V: 1% 13:51:29 V: 98%...
Page 43
13:51:59 param: /philips/pipe 13:51:59 execute nandwrite OK 13:51:59 Writing data to block 0 13:51:59 P: 31% 13:51:59 Writing data to block 4000 13:52:09 /philips/pipe could is closed ________> Finished writing to Squash 13:52:09 m_JffsMounted = 0 13:52:10 P: 63% 13:52:10 WRITE /bffs2/ ________>...
Page 44
USB storage device. The seetypeplate_seetypeplate will be filled in depending on the type of set. 5. This .bin file can only be interpreted in a Philips development centre. Please give this input to your Philips Service contact person.
Block Diagrams, Test Point Overview, and Waveforms Q529.1E LA Wiring Diagram 42” (VE8) WIRING DIAGRAM 42” (STYLING VE8) *AMBI-LIGHT UNIT *AMBI-LIGHT UNIT *AMBI-LIGHT UNIT (IN BACK COVER) (IN BACK COVER) (IN BACK COVER) (1176) (1175) (1174) 1M83 1M84 1M83 1M59 1M90 1M84 (AL3)
Page 50
Block Diagrams, Test Point Overview, and Waveforms Q529.1E LA Wiring Diagram 47” (VE8) WIRING DIAGRAM 47” (STYLING VE8) AMBI-LIGHT UNIT AMBI-LIGHT UNIT AMBI-LIGHT UNIT (IN BACK COVER) (IN BACK COVER) (IN BACK COVER) (1176) (1175) (1174) 6 LED 8 LED 6 LED 1M83 1M84...
Block Diagrams, Test Point Overview, and Waveforms Q529.1E LA Block Diagram Video VIDEO B02B B05E MAIN TUNER 7T57 PNX8541 PNX5100: PNX5100: LVDS TDA9898HL 7C00 1G50 7H00 1T04 1T55 PNX8541E/M1 PNX5100EH/M1A IF-FILTP1 TD1716F/BHXP 7T56 IF1-A 10-bit YUV B04K ANALOGUE AV CVBS4 B04O DIGITAL B05E...
Block Diagrams, Test Point Overview, and Waveforms Q529.1E LA Supply Lines Overview SUPPLY LINES OVERVIEW B01B DC / DC B01C SUPPLY DC/DC B03F STI701: DEBUG B04P PNX8541: POWER B09A B06B LED PANEL CONTROL USB 2.0 +3V3 +3V3 +1V2-PNX8541 +1V2-PNX8541 B01a +3V3-STANDBY +3V3-STANDBY B01b...
Circuit Diagrams and PWB Layouts Q529.1E LA SSB: SRP List Explanation Example Personal Notes: 1 . 1 . Introduction Net Name Diagram +12-15V AP1 (4x) +12-15V AP4 (4x) SRP (Service Re ference Protocol) is a softw are too l that creates a list w i th all refer e n c es to signal lines. The list contains +12-15V AP5 (12x) references to the signals w i thin all schemat ics of a PWB.
Alignments Q529.1E LA EN 175 8. Alignments Index of this chapter: • Switch the set to stand-by mode. 8.1 General Alignment Conditions 8.2 Hardware Alignments For the next alignments, supply the following test signals via a 8.3 Software Alignments video generator to the RF input: 8.4 Option Settings •...
Page 176
EN 176 Q529.1E LA Alignments Table 8-2 Tint settings digital diagnosis possible, the microprocessor has to know which ICs to address. The presence / absence of these specific ICs (or functions) is made known by the option codes. Colour Temp. Cool Notes: Normal...
Page 177
Alignments Q529.1E LA EN 177 8.4.4 Opt. No. (Option numbers) Select this sub menu to set all options at once (expressed in The first line (group 1) indicates hardware options 1 to 4, the two long strings of numbers). second line (group 2) indicates software options 5 to 8. An option number (or “option byte”) represents a number of Every 5-digit number represents 16 bits (so the maximum value different options.
Page 178
EN 178 Q529.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9. Circuit Descriptions, Abbreviation List, and IC Data Sheets Index of this chapter: overview of the TV522/92 architecture can be found in next 9.1 Introduction figure “Architecture of TV522/92 platform”. 9.2 Main Supply Sets with all resolutions @ 50 Hz use the PNX85xx SoC and 9.3 On-Board Platform Supply...
Page 179
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q529.1E LA EN 179 TV522/92 Architecture Block Diagram Pixelated Ambilight TDA10043 DVB-C DDR-II DDR-II TDA10048 Matrix DVB-T Matrix PNX5100 FHD@120p FHD@120p Halo Free PNX8541 FHD@100p FHD@100p HD-NM FHD 120Hz Hybrid Tuner FPGA : MASTER IF Pixelated AL FLASH...
Page 180
EN 180 Q529.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.1.3 SSB Cell Layout SERVICE CONNECTOR PNX5100 SIDE I/O ANALOG I/O AUDIO CLASS - D PNX85XX TUNER DC - DC CONVERSION COMMON INTERFACE MPEG4 (OPT) DIGITAL I/O I_17660_120.eps 140308 Figure 9-2 SSB top view...
Page 181
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q529.1E LA EN 181 Main Supply removed. It operates within a range of 120 to 140% of the nominal value. 9.2.1 32" Sets DPS-182CP A The supply unit delivers the following voltages to the chassis: The 32"...
Page 182
EN 182 Q529.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets The supply unit delivers the following voltages to the chassis: • The internal protection works together with the output over- voltage detector transistors 7U07-1 and 7U07-2. 1316 1319 1M09 1M90 1M95...
Page 183
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q529.1E LA EN 183 Over-current Detection For digital reception, the application in this chassis is as Over-current detection is done via components 3U05, 3U06, follows: 3U15, 3U14, and 2U04 for the 3.3 V converter and 3U00, 3U01, •...
Page 184
EN 184 Q529.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets DVB-C DVB-C 4MHz 4MHz Wideband AGC Wideband AGC TDA10023 TDA10023 Tuner Tuner 10-bit 10-bit Decoding Decoding interface interface TD1716_Mk4 TD1716_Mk4 X6874D X6874D X3451K X3451K DVB-T DVB-T 7MHz 7MHz 5,8MHz 5,8MHz 8MHz...
Page 185
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q529.1E LA EN 185 DVB-C 4MHz Nested AGC TDA10023 Tuner 10-bit Decoding interface TD1716_Mk4 X6874D X3451K DVB-T 8MHz 8MHz 7MHz 5,8MHz TDA10048 36.13MHz 37.6MHz 36.125MHz 36.125MHz 10-bit Decoding interface IF AGC TDA9898 SIF AGC Side Band Band Pass...
Page 186
EN 186 Q529.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets H_16770_124.eps 130707 Figure 9-8 PNX85xx video flow diagram The Analogue Video Front-End (AVFE) provides the interface The Video Composition Pipe TV (CPIPE_L2TV) is used to to external analogue baseband video sources and IF inputs. It perform picture improvements on video and merge the video supports the following inputs: layer and 2 graphics layers into a single stream.
Page 187
Baseband Audio Inputs. compressed streams such as MPEG and AC-3. This runs as SW Codecs on the AV-DSP. The Sony/Philips Digital Interface (SPDIF) input is used to get compressed data into the system memory. The multiplexer in 9.6.3 Audio-Video Codec Subsystem front of the block allows two possible sources of SPDIF signals.
Page 188
EN 188 Q529.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets DDR2-SDRAM PNX85xx I2C-3 I2C-DMA3 MIPS MTI-4KeC I2C-2 I2C-DMA2 I2C-1 I2C-Slave I2C-4 System UART-3 Controller PWM’s 80C51 2-wire UART1 GPIO’s PCI/XIO 2-wire UART2 PCI/XIO E-JTAG E-JTAG H_16770_126.eps 130707 Figure 9-10 Control and compute subsystem The Control and compute subsystem consists of the main Back-end processor, control peripherals and the memory system.
Page 189
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q529.1E LA EN 189 LVDS PNX5100 LVDS PNX8541 HD DF fHD DF MIPS StdBy RGB-Ambi Level SPARTAN3 AmbiLight shift 2x DDR PWM Boost Analog Boost Converter Display Analog /PWM PWM Dimming Dimming Converter Supply Analog /PWM Dimming...
Page 190
EN 190 Q529.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.10 Abbreviation List Monochrome TV system. Sound carrier distance is 6.5 MHz Dynamic Frame Insertion 0/6/12 SCART switch control signal on A/V Directions For Use: owner's manual board. 0 = loop through (AUX to TV), DLNA Digital Living Network Alliance 6 = play 16 : 9 format, 12 = play 4 : 3...
Page 191
Europe. Sync On Green Negative Temperature Coefficient, SOPS Self Oscillating Power Supply non-linear resistor S/PDIF Sony Philips Digital InterFace NTSC National Television Standard SRAM Static RAM Committee. Colour system mainly Small Signal Board used in North America and Japan.
Page 192
EN 192 Q529.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets Video Cassette Recorder VESA Video Electronics Standards Association 640 × 480 (4 : 3) Variable Level out: processed audio output toward external amplifier Vestigial Side Band; modulation method WYSIWYR What You See Is What You Record: record selection that follows main...
Page 193
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q529.1E LA EN 193 9.11 IC Data Sheets This section shows the internal block diagrams and pin configurations of ICs that are drawn as “black boxes” in the electrical diagrams (with the exception of “memory” and “logic” ICs).
Page 194
EN 194 Q529.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.11.2 Diagram B02B, TDA9898HL (IC 7T59) Block Diagram 4 MHz reference input EXTERNAL SOUND BAND-PASS FILTER i.c. ADRSEL GNDD LFSYN2 GNDA EXTFILO EXTFILI FREF OPTXTAL 43, 44 40, 41 SYNTHESIZER 4 MHz FREQUENCY C-BUS...
Page 195
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q529.1E LA EN 195 9.11.3 Diagram B02A, TDA10048HN (IC7T17-1) Block Diagram AGC_TUN AGC_IF ANALOG ΣΛ STEP INTERFACE DIGITAL FRONT-END DUAL CHANNEL ESTIMATION AND OFDM AND CORRECTION DEMODULATION ΣΛ STEP INTERFACE DIGITAL DYNAMIC 2K / 4K / 8K TIMESHIFT CANCELLER...
Page 196
EN 196 Q529.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.11.4 Diagram B02C, TDA10023HT (IC7TA4) Block Diagram DDA1 SSA1 DDD3 SSD3 DDD2 SSD2 DDD1 SSD1 DDA2 DDA3 SSA3 DDD4 XOUT 8, 25, 42 14, 30, 43 15, 31, 44 AGCTUN CLOCK RECOVERY...
Page 197
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q529.1E LA EN 197 9.11.5 Diagram B03B to F, STi7100 (IC7A00) Block Diagram 5 x 2-ch S/PDIF PCM out Peripheral I/O SDRAM AudioL 2-ch and external interrupts AudioR PCM in video in Audio ST40 core 266 MHz Serial...
Page 198
EN 198 Q529.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.11.6 Diagram B04, PNX85xx (IC 7H00) Block Diagram DDR-II DDR-II 32 MB 32 MB PNX85xx Matrix Display 1368 × 768 A/V INPUTS MIPS32@240MHz TV control, Pixel OSD Source select 3D-Comb Digital color decoder Audio decoding...
Page 199
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q529.1E LA EN 199 9.11.7 Diagram B05, PNX5100 (IC 7C00) Block Diagram PNX5100EH MEMORY CONTROLLER TM327x 1 LVDS RX 1 GIC 1 Video UIP L3K7 TM327x 2 GIC 2 LVDS RX 2 TM327x 3 GIC 3 PCI/XIO...
Page 200
EN 200 Q529.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.11.8 Diagram B06, XC3S250E Spartan-3 (IC 7F00) Pin Configuration & Description VQ100 Footprint IO_L01P_7/VRN_7 IO_L01N_2/VRP_2 Bank 0 Bank 1 IO_L01N_7/VRP_7 IO_L01P_2/VRN_2 IO_L21P_7 IO_L21N_2 IO_L21N_7 IO_L21P_2 VCCO_2 VCCO_7 VCCINT VCCAUX IO_L23P_7 IO_L24N_2...
Page 201
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q529.1E LA EN 201 9.11.9 Diagram B07E, AD8197A (IC 7P02) Block Diagram Figure 1. TYPICAL APPLICATION 04:20 Pin Configuration AVCC AVCC PIN 1 INDICATOR IN_B0 IP_C3 IP_B0 IN_C3 AVEE AVEE IN_B1 IP_C2 IP_B1 IN_C2 VTTI...
Page 202
EN 202 Q529.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.11.10 Diagram B09A, ISP1564HL (IC 7N00) Block Diagram PME# 77, 98, 100 CC(IO)AUX GLOBAL CONTROL 10, 12 to 15, 20 to 22, AD[31:0] 26 to 31, 33, 34, 50 to 54, 56, 57, PCI CORE VOLTAGE...
Page 203
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q529.1E LA EN 203 9.11.11 Diagram B09B, DP83816AVNG (IC 7N04) Block Diagram Data FIFO Tx MAC Tx Buffer Manager Data FIFO PCI Bus Interface Rx MAC Rx Buffer Manager Rx Filter Pkt Recog Logic SRAM MAC/BIU...
Page 204
EN 204 Q529.1E LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.11.12 Diagram B10A, TPA3120D2 (IC 7D10) Block Diagram TPA3120D2 0.22 F 22 H 470 F ROUT 0.68 F PGNDR 0.68 F PGNDL LOUT BYPASS 22 H 470 F AGND 0.22 F PVCCL...
Page 205
Circuit Descriptions, Abbreviation List, and IC Data Sheets Q529.1E LA EN 205 9.11.13 Diagram V2, UBA2071 (IC 7201) Block Diagram NONFAULT bootstrap diode IREF INTERNAL SUPPLY TIMER REFERENCE LEVEL- SGND CIRCUITS SHIFTER high-side driver CONTROL NON-OVERLAP TIMING OSCILLATOR HARD- low-side SWITCHING driver DETECTION...
Page 206
EN 206 Q529.1E LA Spare Parts List & CTN Overview 10. Spare Parts List & CTN Overview For the latest spare part overview, please consult the Philips Service website. Table 10-1 Sets described in this manual: Styling 32PFL7623D/10 ME8+ 32PFL9603D/10...