Sequence Programming - Whirlpool GR440LXL Use & Care Manual

To Set a Timed Cook:
1. Press BAKE (optional).
2. Press the TEMP "up" or "down" arrow pads to enter a
temperature other than the one displayed.
3. Press STOP TIME.
4. Press the HR and MIN "up" or "down" arrow pads to enter
the desired time to end cooking.
5. Press START. The display will count down the time.
When the time ends, the oven will shut off automatically and
"End" will appear on the display. End-of-cycle tones will
sound, then, if enabled, reminder tones will sound every
minute.
6. Open and close the oven door to clear the display and/or
stop reminder tones.
To Set a Delayed Timed Cook:
Before setting, make sure the clock is set to the correct time of
day. See "Clock" section.
1. Press desired cook function.
2. Press the TEMP "up" or "down" arrow pads to enter a
temperature other than the one displayed.
3. Press START TIME.
4. Press the HR and MIN "up" or "down" arrow pads to enter
the time of day to start.
5. Press STOP TIME (optional).
6. If STOP TIME has been pressed, press the HR and MIN "up"
or "down" arrow pads to enter the desired time to end
cooking.
7. Press START. "DELAY" will appear on the display.
When the start time is reached, the oven will automatically
turn on. When the stop time is reached (if programmed), the
oven will shut off automatically and "End" will appear on the
display. End-of-cycle tones will sound, then, if on, reminder
tones will sound every minute.
8. Open and close the oven door to clear the display and/or
stop reminder tones.

Sequence Programming

(on some models)
Sequence Programming allows you to program at one time up to
four cook functions, and is usable with other electronic oven
control functions, such as the Timer and Warming Drawer.
Sequence Programming takes precedence over any non-
sequenced cook function. For example, if an untimed Bake
function is in process and a sequence program is started, the
untimed Bake function will be canceled, and the program
sequence will start.
All steps of a sequenced program must be programmed with a
stop time. If a stop time is not entered for a step in the sequence
program, and the FIRST/NEXT STEP pad is pressed, three tones
will sound.
To Program the First Step of the Sequence:
1. Press FIRST/NEXT STEP. "PROGRAM" and "STEP" will
appear on the display. A flashing "1" will also appear on the
display, indicating that step 1 is being programmed.
2. Choose the desired cook function by pressing any cook
function key.
14
3. Press START TIME, then HR and MIN "up" or "down" arrow
pads to set the time of day for the first cook function to begin.
If START TIME is not pressed, then the sequence of cook
functions will begin immediately once programming is
complete and START is pressed.
The display will show either the time of day (if start time was
not programmed) or the start time (if same was programmed),
but with a flashing colon. "Stop" and "Time" will also appear
on the display.
4. Press STOP TIME, then HR and MIN "up" or "down" arrow
pads to set the time of day for the first cook function to stop.
To Program Next Steps of the Sequence:
1. Press FIRST/NEXT STEP. "PROGRAM" and "STEP" will
appear on the display. The number of the steps being
programmed will flash.
"START" and "TIME will appear on the display.
2. Choose the desired cook function by pressing any cook
function key.
3. Press TEMP "up" or "down" arrow pad (if desired) to select
temperature.
4. Press STOP TIME, then HR and MIN "up" or "down" arrow
pads to select stop time.
5. Press START to begin sequence.
6. Press CANCEL at any time to clear program and to stop
program.
To Review/Modify Programmed Sequence:
If program steps are partially or completely programmed, yet the
sequence has not been started, the programmed cook functions
can be reviewed.
1. Press REVIEW STEPS. Step 1 will appear in the display.
Subsequent presses of REVIEW STEPS will cause display of
programmed steps in order.
"STEP" and "RECALL" will appear on the display. The
number of the displayed step will flash. A recalled step will
remain lit on the display for 5 minutes if no further action is
taken.
2. If fewer than four steps have been programmed, press
REVIEW STEPS repeatedly until the last programmed step is
displayed, then press FIRST/NEXT STEP if it is desired to
program an additional step.
While a step is recalled, a cook function pad can be used to
change the function, or the TEMPERATURE "up" or "down"
arrow pad can be used to change the set temperature.
START TIME, when used with the HR or MIN "up" or "down"
arrow pads, can be used to change, add or delete a delayed
start. STOP TIME can be used to change the stop time.
Changing the stop time of a step will automatically change
the start times and stop times of all subsequent programmed
cook functions.
3. After Review/Modification of the programmed sequence is
complete, press START to begin sequence.
To Modify Sequence Programming:
1. Press UNDO.
The last step of the sequence will be canceled, and the step
prior to the canceled sequence will show on the display for
either review or modification.
If the programmed sequence has not been started, see "To
Program Next Steps of the Sequence" section to program a
step to replace the canceled cook function.