Advertisement
Quick Links
Softlog Systems (2006) Ltd.
1 Installing ICP2 and ICP2-GANG on USB Port
The following steps will show how to install the device under Windows XP. Basically, the procedure is also
somewhat the same for other Windows operating systems.
1. Power on your PC and boot to Windows
2. Install ICP Family software from supplied CD or from
directory "C:\Program Files\Soft-Log\IcpWin"
3. Connect ICP2/ICP2-GANG to the PC with a USB cable. "POWER" LED on ICP2 may not work until
device is not installed on USB port
4. Windows will detect the new device and will initiate the "Found New Hardware Wizard" prompting you to
install the software for the detected USB device
5. Select "No, not this time". Click "Next" to continue
6. Select "Install from a list or specific location (Advanced)". Click "Next" to continue
18 Rojansky St, P.O.B. 17007, Rishon-Letzion 75070 Israel, Fax: 972-3-9527520
E-mail:
sales@softlog.com
www.softlog.com
(file IcpWin_setup_x_xx.exe) to
Web:
www.softlog.com
Advertisement
Related Manuals for Softlog Systems ICP2
Summary of Contents for Softlog Systems ICP2
- Page 1 (file IcpWin_setup_x_xx.exe) to directory “C:\Program Files\Soft-Log\IcpWin” 3. Connect ICP2/ICP2-GANG to the PC with a USB cable. “POWER” LED on ICP2 may not work until device is not installed on USB port 4. Windows will detect the new device and will initiate the “Found New Hardware Wizard” prompting you to install the software for the detected USB device 5.
- Page 2 ICP2 USB Driver Installation 7. Specify path to the driver: “C:\Program Files\Soft-Log\IcpWin\ICP2_USB_Driver”. Click “Next” to continue 8. Click “Continue Anyway” 9. Click “Finish” Rev: July-2007 Page 2 of 8...
- Page 3 ICP2 USB Driver Installation 10. Windows will detect the new device again and will initiate the “Found New Hardware Wizard” prompting you to install the software for the detected USB device 11. Select “No, not this time”. Click “Next” to continue 12.
- Page 4 ICP2 USB Driver Installation 13. Specify path to the driver: “C:\Program Files\Soft-Log\IcpWin\ICP2_USB_Driver”. Click “Next” to continue 14. Click “Continue Anyway” 15. Click “Finish” Rev: July-2007 Page 4 of 8...
-
Page 5: Verifying The Installation
ICP2 USB Driver Installation 2 Verifying the Installation This section will guide you on how to verify if the ICP2 USB was properly installed. You will also need to determine the COM port assignment made by Windows for the ICP2 USB port To verify if the device is properly installed and determine the COM port assignment of the device: 1. - Page 6 ICP2 USB Driver Installation 4. You should see “ICP2 USB to UART Bridge Controller (COMx)” in device listing. It also means that Windows has assigned the ICP2 to COMx Rev: July-2007 Page 6 of 8...
-
Page 7: Uninstalling The Device
3 Uninstalling the Device It’s easy to uninstall the ICP2 USB driver 1. Click Start → Settings → Control Panel 2. Double-click “Add or Remove Programs” 3. Select “ICP2 USB to UART Bridge Controller” and click “Change/Remove” Rev: July-2007 Page 7 of 8... - Page 8 ICP2 USB Driver Installation 4. Click “Yes” 5. Click “No” 6. Click “OK” Rev: July-2007 Page 8 of 8...
Need help?
Do you have a question about the ICP2 and is the answer not in the manual?
Questions and answers