Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Web Techniques WT-25LC
Summary of Contents for Web Techniques WT-25LC
- Page 1 Owner's Manual and Guide to Operations MODEL WT-25LC & WT-25LCI ROLL LABEL REWIND MACHINES IMPORTANT: Read all instructions before using. 910 Bolger Court, Fenton, MO 63026 (USA) (636) 343-0806 (800) 325-9777 07-1036 Metric CDR...
-
Page 2: Table Of Contents
Table of Contents Safety Instructions ............1 Count Labels/Count Length Switch ......7 Dark Energize/Light Energize Switch ......7 Purpose (General Overview) .......... 1 Count Up/Count Down Switch ........7 Operator Controls (Web Transport System) ....1 Count/Standby Switch ..........7 Rewind Direction Switch .......... -
Page 3: Safety Instructions
SAFETY INSTRUCTIONS PURPOSE (GENERAL OVERVIEW) WT-25LC and WT-25LCI series rewind machines are RULES FOR SAFE OPERATION made for the purpose of rewinding rolls of narrow web 1. Know your machine. Read and understand the products. In general, these are paper, film or foil prod- owner’s manual and labels affixed to the machine. -
Page 4: Main Speed Control Knob
START pushbutton will also reset the counter Web Techniques rewind machines are available with to zero if the counter stop setting (Preset B) has been various types of coreholders. Lift-off cam-lock core- reached. -
Page 5: Air Inflatable Coreholders (Optional)
be able to see that it is fully engaged and will have NOTE to rely on feel. An alternate method of loosening the roll on the rewind is to hold the roll tight against the top of the table and turn the coreholder in the direction opposite to the way CAUTION!! it was running. -
Page 6: Rewinding
C) Allow the roll to expand as it turns in the reverse direction. D) Once the roll is loosened all the way to the defect, stop the motor. E) Reverse the DIRECTION SWITCH and re-tighten the roll. Figure 1A Web Path for WT-25LC Models 07-1036... -
Page 7: Counting System
deny access to the functions not required for our COUNTING SYSTEM application. The rewind machine incorporates a bi-directional dual preset counter. This permits the operator to set sepa- While it is possible for the counter program to become rate deceleration (Preset A) and stop (Preset B) points. scrambled (possibly due to line noise, electrical storms, The counting system can be operated in either the pho- etc.), it is important to note that this will disable the... -
Page 8: Automatic Reset (Length Mode Only)
However due to circumstances reached. You may reset the counter to zero at any time beyond its control, Web Techniques, Inc. can make no by pushing the “RST” button on the counter. guarantees as to the accuracy of count. The following... -
Page 9: Photoelectric Counting System Controls
ADJUSTMENT) COUNT LABELS/COUNT LENGTH SWITCH The thru-beam and capacitance type scanners used with WT-25LC/LCI machines have built in sensitivity This switch allows the operator to select one of two controls. The sensitivity adjustment on the counter modes of counting. In the length mode the counter in-... -
Page 10: Resetting The Counter
scanner is locked, depress and hold the "Auto Ad- RESETTING THE COUNTER just" button on the side of the sensor for six (6) se- When operating in the photoelectric counting mode, conds to unlock the scanner. the counter must be manually reset to zero by means of C) Place a strip of label material into the slot of the the “RST”... -
Page 11: Detecting Punched Holes
The following list of settings has been pre-adjusted by ble from the lamp to the “LAMP” connector on the Web Techniques, Inc. to cover most applications. If control unit. Use the plastic cable ties provided with these settings are not optimal for your requirements, the lamp to route the cable along the back of the adjustments may be made with discretion. -
Page 12: Operation
3. Set “A XX.X” to “A 00.0” and press Enter. flash erratically or not at all, replace the flash tube 4. Set “b XX.X” to “b 00.0” and press Enter. (available from Web Techniques). SETTING THE COUNTER LOCK CODE 1. Press PRGM 3 times (until “LoC” appears).
Need help?
Do you have a question about the WT-25LC and is the answer not in the manual?
Questions and answers