WARNING – A specific hazard or unsafe practice, which could result in severe personal injury or death if proper precautions are not taken. CAUTION – Unsafe practices which could result in personal injury if proper precautions are not taken, or a reminder of good safety practices. Corn Reel V2.0...
Page 4
Operation of the Corn Reel shall be limited to competent and experienced persons. In addition anyone who will operate or work around the Corn Reel must use good common sense. In order to be qualified, they must also know and meet all other requirements, such as: Some regulations specify that no one under the age of 18 may operate power machinery.
Page 5
YOU are responsible for SAFE operation and maintenance of your Corn Reel. YOU must ensure that you and anyone who is going to operate maintain, or work around the corn reel must be familiar with the operating, maintenance, and safety information contained in the manual. This manual will take you step by step through your working day and alerts you to all good safety practices while operating the corn reel.
MACHINE INSPECTION After delivery of your new Corn Reel and/or completion of assembly, before each use, inspection of the machine is mandatory. This inspection should include, but not be limited to: Check to see that all guards are in place, secured and functional.
Page 7
Corn Reel Decal Locations and Part Numbers TS2001 TS2017 CSP152 TS2003 BC2515 Minden Machine Shop Inc. 1302 K Road Minden, NE 800-264-6587 / 308-832-0220 Corn Reel V2.0...
Corn Reel Assembly Instructions Orientation: Sitting in the operator seat facing forward. Lower the corn head to the ground if attached to the combine. Shut off the engine and remove the key from the ignition switch. Thread two shafts together (if necessary) and lay them out in front of your head. The shaft with the female coupler will have to be on the right side of the machine.
18. Check that all fasteners are tightened and the reel is clear of obstructions. 19. Check that the work area is clear and safe to operate the corn reel. Perform a test run of the reel. If the reel operates backwards, switch the hoses at the combine. Retest.
Page 11
Corn Reel Assembly 8 row machine shown Part quantity will vary with machine size Angle Adjustment Bolt Hydraulic Hoses Raise/Lower R1706A-108P10-12000 Qty. 2 Guide Bolts DETAIL C 31 32 33 34 39 40 DETAIL B Loosen u-bolts on bearing mounts to adjust...
Page 12
Corn Reel Parts List Parts List Parts List ITEM QTY ITEM QTY PART NUMBER DESCRIPTION PART NUMBER DESCRIPTION B1/4X1 CR-A016 Beam Arm Tube Assembly Hex Bolt Varies with Size Sprocket Driven Shaft Assembly W1/4F Flat Washer CR-A015 Double Arm Bat Assembly...
Page 13
Corn Reel Beam Mounts Inner Case Narrower Beam Clamp Outer CR-A028 10 Series Heads CR-A029 CR-A021 Geringhoff Pre-2012 Beam Mounts Geringhoff North Star Elite Inner Beam Mount Outer CR-A037 CR-A030 CR-A031 Geringhoff 2012 and Newer Beam Mounts Round Tube Note: Universal Beam Clamp includes two different lengths of bolts.
Page 14
(N.m) manual. When using manual. When using locking elements, increase locking elements, increase torque values by 5%. torque values by 5%. 1206 Grade or Class value for bolts and capscrews are identified by their head markings. Corn Reel V2.0...
Page 16
KEYWAY CUTOUT THIS SIDE CHAIN GUARD SHOULD NOT RUB ON REEL BAT ALTERNATE ALL BATS 90 6 1/8 GUARD MOUNT BRACKET THIS LOCATION ONLY 22 1/8 4 ROW 36" BASIC SPACING FOR 38" AND 40" ADD CORRECT DISTANCES Corn Reel V2.0...
Page 17
CHAIN GUARD SHOULD NOT RUB ON REEL BAT ALTERNATE ALL BATS 90 LH SHAFT HAS KEYWAY CUTOUT MOTOR MUST BE ON LH SIDE GUARD MOUNT BRACKET THIS LOCATION ONLY CENTER COUPLER ON 6 ROW 30" BASIC SPACING CENTER SNOUT Corn Reel V2.0...
Page 18
CHAIN GUARD SHOULD NOT RUB ON REEL BAT ALTERNATE ALL BATS 90 LH SHAFT HAS KEYWAY CUTOUT MOTOR MUST BE ON LH SIDE GUARD MOUNT BRACKET THIS LOCATION ONLY CENTER COUPLER ON 8 ROW 30" BASIC SPACING CENTER SNOUT Corn Reel V2.0...
Page 19
CHAIN GUARD SHOULD NOT RUB ON REEL BAT ALTERNATE ALL BATS 90 LH SHAFT HAS KEYWAY CUTOUT MOTOR MUST BE ON LH SIDE GUARD MOUNT BRACKET THIS LOCATION ONLY CENTER COUPLER ON 8 ROW 38" BASIC SPACING CENTER SNOUT Corn Reel V2.0...
Page 20
CHAIN GUARD SHOULD NOT RUB ON REEL BAT ALTERNATE ALL BATS 90 LH SHAFT HAS KEYWAY CUTOUT MOTOR MUST BE ON LH SIDE GUARD MOUNT BRACKET THIS LOCATION ONLY CENTER COUPLER ON 12 ROW 22" BASIC SPACING CENTER SNOUT Corn Reel V2.0...
Page 21
CHAIN GUARD SHOULD NOT RUB ON REEL BAT LH SHAFT HAS KEYWAY CUTOUT MOTOR MUST BE ON LH SIDE ALTERNATE ALL BATS 90 GUARD MOUNT BRACKET THIS LOCATION ONLY CENTER COUPLER ON 12 ROW 30" BASIC SPACING CENTER SNOUT Corn Reel V2.0...
Page 22
CHAIN GUARD SHOULD NOT RUB ON REEL BAT LH SHAFT HAS KEYWAY CUTOUT ALTERNATE ALL BATS 90 MOTOR MUST BE ON LH SIDE GUARD MOUNT BRACKET THIS LOCATION ONLY CENTER COUPLER ON 16 ROW 22" BASIC SPACING CENTER SNOUT Corn Reel V2.0...
Page 23
RUB ON REEL BAT LH SHAFT HAS ALTERNATE ALL BATS 90 KEYWAY CUTOUT MOTOR MUST BE ON LH SIDE GUARD MOUNT BRACKET THIS LOCATION ONLY 3 1/2 3 1/2 CENTER COUPLER ON 24 ROW 20" BASIC SPACING CENTER SNOUT Corn Reel V2.0...
It is the policy of Minden Machine Shop Inc. to improve its products whenever possible and practical to do so. We reserve the right to make changes, improvements and modifications at any time without incurring the obligation to make such changes, improvements and modifications on any equipment sold previously. Corn Reel V2.0...
Page 25
308-832-1340. Dealer Information: Not Applicable, check here: [ ] Dealer Name: Address: City: State: Zip Code: Phone #: Email: End User Information: Purchaser: Address: City: State: Zip Code: Phone #: Email: Equipment: Serial #: Date Of Purchase: Corn Reel V2.0...