Table of Contents
Advertisement
MTS Broadcast/VHS Hi-Fi Stereo System
Connection
Make the Audio/Video Connection as shown on page 3.
• You can use a TV connected to Stereo amp and speakers instead of a Stereo TV.
TV
VCR
R
L
AUDIO OUT
R
R
L
VHF/UHF
OUT TO TV
Receivable Broadcast Types
The following are possible audio broadcast types and on-screen displays.
The signal being received is indicated with an " " mark while the selected audio mode is
indicated with an arrow.
To display the broadcast signal being received,
➛ ➛ ➛ ➛ ➛ press DISPLAY*.
MTS Stereo and SAP broadcast
Multi-channel Television Sound Stereo (main language)
and Secondary Audio Program (sub language)
broadcasts are being received simultaneously.
Select STEREO or SAP audio mode.
MTS Stereo broadcast
Multi-channel Television Sound Stereo broadcast.
Select STEREO audio mode.
• If stereo broadcast is weak and display flickers,
select MONO audio mode for possible better results.
SAP broadcast
Secondary Audio Program (sub language) broadcast.
Select SAP audio mode for the sub language.
MONO broadcast
Normal monaural sound broadcast.
Audio Mode for Recording
1
Press SAP/ Hi-Fi to display audio mode.
(Display disappears after 5 seconds.)
2
Press SAP/ Hi-Fi
repeatedly to select
STEREO
SAP
desired mode.
MONO
• Refer to "Receivable
Broadcast Types"
above.
• Arrow indicates selection.
3
Make a recording.
See p. 5 of "Basic Operations"
Instruction book.
Notes
• Only tapes recorded in Hi-Fi stereo will playback with true stereo sound. Standard stereo tapes
will playback in monaural sound.
• To listen to Hi-Fi stereo playback, the VCR AUDIO (L/R) jacks must be connected to a stereo TV
or an external stereo amp and speakers. (See top of this page.)
• If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.
• Hi-Fi and normal audio playback volume level may differ.
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
Equipped with
Reduction for true MTS
reproduction.
Stereo Amplifier
Reduction is required for good
stereo separation and audio
fidelity.
®
is a registered
AUDIO IN
R
trademark, and is licensed by
L
®
Technology Licensing.
CH 02
STOP
1 2 : 0 0AM
0 : 0 0 : 0 0
STEREO
SAP
MONO
STOP
1 2 : 0 0AM
CH 02
0 : 0 0 : 0 0
STEREO
SAP
MONO
STOP
1 2 : 0 0AM
CH 02
0 : 0 0 : 0 0
STEREO
SAP
MONO
CH 02
STOP
1 2 : 0 0AM
0 : 0 0 : 0 0
STEREO
SAP
MONO
Audio Mode for Playback
1
Start playback.
See p. 5 of "Basic Operations"
Instruction book.
2
Press SAP/ Hi-Fi to display audio mode.
(Display disappears after 5 seconds.)
3
Press SAP/ Hi-Fi
repeatedly to select
H I F I : L / R
desired mode.
H I F I : L
H I F I : R
NORMAL
• Select "HIFI(L/R)"
or "HIFI(L)" or
"HIFI(R)" to listen to
stereo recordings in
• Arrow indicates
stereo sound.
selection.
Select "NORMAL"
for monaural sound.
- 4 -
Tape Operation
Search System
For each recording, an invisible index mark is placed on the tape. A program index and
information are also included for timer recordings. These marks are used to access or
scan recordings.
Index Search
®
-TV Noise
1
SEARCH
INDEX
PROG. END
MOVIE
®
-TV Noise
ENTER INDEX NUMBER :1
USING 1- 9 KEYS
FORWARD SEARCH :FF
REVERSE SEARCH :REW
NEXT
:SEARCH M/A SK I P
EXIT
:STOP
2
INDEX SEARCH
FORWARD SEARCH :FF
REVERSE SEARCH :REW
SP
To Calculate Index Number
Example 1:
To go to rec. 2 from rec. 4, enter 3 and press REW.
1
2
3
SP
Example 2:
To go to rec. 6 from rec. 2, enter 4 and press FF.
1
2
3
NOTE:
indicates start points of each recording.
SP
Note
• If Index Search is started very close to an
index mark, that index mark may not be
counted in the search.
SP
Repeat Play
Set to playback a recording over and over.
1
Press ACTION to display menu.
2
VCR
C / A
CLOCK
CH
REPEAT PLAY
: OFF
REMOTE WARNING
: ON
AUTO SHUT- OFF
: OFF
AUTO VCR/TV
: ON
IDIOMA/LANGUE : ENGLISH
VCR' S OUTPUT CH : 3
SELECT :
SET :
EXIT
: ACT I ON
3
Press ACTION to return to normal screen.
Program End Search
Press SEARCH to
Locates end point of recording for continuity.
display SEARCH in Stop
1
Press SEARCH twice to display SEARCH
or Play mode, and then
in Stop or Play mode.
press NUMBER keys
to select recording
number.
2
SEARCH
INDEX
PROG. END
• To calculate number,
see below.
Press FF or REW to
SEARCH START :FF
start search.
NEXT
:SEARCH M/A SK I P
EXIT
:STOP
Play begins at search
end. To search forward
or back 1 index, press
Examples of Program End Search.
Examples of Program End Search.
FF or REW while
screen left is displayed
Fig. 1
(10 sec.).
• To cancel, press
Program 1
STOP or PLAY.
the current tape position
Press SEARCH button
FF
Fig. 2
Program 1
4
5
6
7
Fig. 3
the current tape position
Press SEARCH button
Program 1
End Point
4
5
6
7
Upon locating end point,
➛ search continues 7 sec. past end point,
➛ tape rewinds to 10 sec. before end point,
➛ tape plays to end point and stops.
Notes
• If Program End Search is started very close
to an index mark, that mark may be skipped
over.
• To cancel, press PLAY or STOP.
Zero Search
To quickly return to a specified tape location.
1
Press DISPLAY during play to display
Counter.
Press
to select
2
PLAY
1 2 : 0 0AM
REPEAT PLAY and
press
to set ON or
OFF.
ON : Play repeats at tape end
or if unrecorded portion
over 30 sec. is detected.
3
Continue to record, playback, etc.
4
Press STOP.
5
REW
1 2 : 3 0AM
STOP
1 2 : 3 1AM
- 5 -
Press FF to start
MOVIE
PROGRAM END
SEARCH.
• To cancel, press
STOP or PLAY.
Program 2 or BLANK
End Point
BLANK
Program 2
BLANK
the current tape position
Press SEARCH button
End Point
FF
BLANK
Program 2
If search
FF
exceeds a few
seconds in
BLANK area.
Press RESET
0 : 0 0 : 0 0
COUNTER at desired
SP
position to reset to
"0:00:00".
Press CA/ZERO in
CH 02
0 : 30 : 30
Stop mode to start
SP
ZERO SEARCH.
• Unit will go into FF
or REW mode and
stop at the last point
the Counter was set
to 0:00:00.
CH 02
0 : 0 0 : 0 0
SP
Hide quick links:
Advertisement
Table of Contents
