Related Manuals for Relyon plasma Brush
Summary of Contents for Relyon plasma Brush
- Page 1 Table of contents Operating instructions USB communication package BA-KommUSB_EN / F0352200 June 2016 BA-KommUSB_EN / F0352200...
- Page 2 Table of contents Thank you for purchasing a high-quality relyon plasma GmbH product. To get the best from your product, please read these instructions carefully. Important! Read these instructions carefully before assembling, installing and starting up the machine! Always follow the safety instructions! Failure to follow the safety instructions may result in accidents, serious injury and serious damage to the machine.
-
Page 3: Table Of Contents
Table of contents Safety ............................4 Residual risks ............................ 4 Information and obligations for the operator ..................4 Intended use ............................. 4 Impermissible operating conditions ....................5 System description ........................6 Function ............................6 System overview ..........................6 2.2.1 Description of the components ................... 6 2.2.2 Scope of delivery ........................ -
Page 4: Safety
Any modifications made to the machine will invalidate the operating licence and the warranty. Exception: Such modifications are expressly authorised by the manufacturer. Intended use The system is intended solely for operation with the PS2000 high-voltage source and a plasma generator from relyon plasma GmbH. June 2016 BA-KommUSB_EN / F0352200... -
Page 5: Impermissible Operating Conditions
Coupled with a suitable plasma generator, the machine is intended solely for the plasma treatment of surfaces (metals, textiles, glass and plastics) to activate, clean, coat or remove residue at atmospheric pressure. Under no circumstances may the system be used by non-trained persons. Impermissible operating conditions The system must not be operated under the following conditions: •... -
Page 6: System Description
System description Function The components of this system are the basic elements for communicating with a PS2000 current source using a Windows PC over USB. System overview 2.2.1 Description of the components No. Components PC/CAN Interface USB-to-CAN compact CAN cable (length 2 m) CAN terminal resistor (Sub-D) CAN terminal resistor bushing (Sub-D) USB stick with software... -
Page 7: Scope Of Delivery
2.2.2 Scope of delivery The scope of delivery includes the following components: • PC/CAN Interface USB-to-CAN compact • CAN cable (length 2 m) • CAN terminal resistor (Sub-D) • CAN terminal resistor bushing (Sub-D) • USB stick with software • Operating instructions Transport / storage •... -
Page 8: System Component Installation
System component installation To install the system, carry out the following steps in the order specified: 1. Connect the CAN terminal resistor (bushing) to the "USB-to-CAN" PC/CAN interface. 2. Connect the CAN cable to the CAN terminal resistor (bushing). 3. Connect CAN cable to the rear connection of the PS2000 current source. 4. -
Page 9: Operation
2. Install the VCI driver by running the "VCI_Treiber_###.exe" file in the "VCI-Installer" subfolder. This may require administrator rights. Follow the instructions in the program to complete the installation 3. Carry out the "setup.exe" file in the "plasma control V2.1" subfolder. This may require administrator rights. - Page 10 Menu item Explanation Operating mode During operation, all necessary commands can be run on the "Operating Mode" tab. Further details can be found in 5.2.1 Settings One-time settings for the storage location can be entered under "Settings". Further details can be found in 5.3.1 (Version number) In the header, you can read off the version number of the software (shown in V2.1)
-
Page 11: Operating Mode" Menu Item
5.2.1 "Operating Mode" menu item Menu item Explanation Plasma ON Pressing this button activates/deactivates the high (Plasma OFF) voltage and the plasma on the plasma generator is ignited/stopped. The button appears red during an active plasma generation process. To be able to start the plasma generation process, there can be no error messages in the status field (#7). - Page 12 (Comments field) In this field, you can enter any text that is to be stored with your measurement data. These entries can be process parameters or identification numbers. Power This is the power set value input of the current source in a percentage.
-
Page 13: Settings" Menu Item
5.2.2 "Settings" menu item Menu item Explanation Data Name Suffix As an option, you can enter a desired suffix for the data recording files here. The suffix is appended to the part of the file name that cannot be changed, which consists of the date and time of the data recording. -
Page 14: Data Recording Sample File
5.2.3 Data recording sample file The file is stored in the selected directory or in the standard working directory in accordance with the naming system described under point 5.2.2. The file format is .csv with the ";" delimiter (semicolon). A sample file is listed below to show an example of the content and the structure. All standard settings have been retained for the sample file. -
Page 15: Environment
Electrical and electronic equipment used must not be disposed of along with normal waste. The machine contains valuable materials that can be recycled. Take the machine to a suitable collection point. relyon plasma GmbH Weidener Strasse 16 93057 Regensburg Germany...
Need help?
Do you have a question about the Brush and is the answer not in the manual?
Questions and answers