Organize; Enter The Organize View; Swap Two Programs; Move A Program - Clavia Nord Wave 2 User Manual

16 | nORD WaVe 2 USeR ManUal OS V1.0x

ORGanIZe

The order in which programs are stored in their respective banks can be
rearranged using the Swap and Move ORGANIZE functions:

enTeR THe ORGanIZe VIeW

1
Press ORGANIZE (Shift + live button) to enter the Organize view.
Program
A:24 Ac Guitar Finger
A:25 Mini M Bass 4
A:31 Gate Filter Whl
A:32 Pacific Pad Whl

SWaP TWO PROGRaMS

a Swap operation interchanges the positions of two programs:
2
Use the dial to select the program location which should be
swapped with another and press Swap.
3
Use the dial to select the destination and press Ok to complete the
Swap operation. Pressing Undo will instead cancel the operation.
Program Program
A:24 Ac Guitar Finger
A:25 Mini M Bass 4
A:31 Gate Filter Whl
A:32 Pacific Pad Whl

MOVe a PROGRaM

4
Use the dial to select a program which should be moved to another
location and press Move
Program
A:24 Ac Guitar Finger
A:25 Mini M Bass 4
A:31 Gate Filter Whl
A:32 Pacific Pad Whl
5
Select the destination location for the operation, using the dial and
press Ok. Pressing Undo will instead cancel the operation.
E Note that programs between the source and destination locations
are shifted one step up or down, changing which programs are
part of each page within the range involved.
M
Content can also be organized using the Nord Sound Manager.

MIDI leD InDIcaTOR

The MIDI leD, located to the left of the display, blinks as
incoming MIDI messages are received by the MIDI In port, or
through the USB connector.
M
Short flashes indicates any kind of incoming MIDI data, longer
flashes indicates MIDI data that the Wave 2 actually uses.
Organize
Swap Move
A:25
Undo Ok
A:25
Undo Ok

MOnITOR / cOPY / PaSTe

To display what a parameter on the panel is set to,
without changing it, hold down the MONITOR button
and turn the associated parameter knob.
The COPY button can be used not only for copying a
layer, but also for copying a program or a morph, as well as patterns:
1
Make a copy by holding down the COPY button in combination with
one of the options below:
• To copy a Layer, press one of the LAYER A-D buttons
• To copy a Morph, press the VELOCITY, WHEEL, ATOUCH or
CTRLPED button
• To copy a Pattern, press PATTERN (Shift + arp/Poly/Gate)
• To copy a Program, press one of the PROGRAM 1-5 buttons.
2
To paste the copied settings, hold down PASTE (Shift + Monitor/
copy Panel) and the button corresponding to the layer, morph,
pattern or program the settings should be pasted into. layers and
morphs can either be pasted within the program they were copied
from, or into any other program.

MORPH

Morphs allow for controlling several parameters at once
using one control "source". for example, a foot pedal
can be used to control the balance between two layers,
the wheel to change the filter cut-off, and the rate of a
selected effect controlled by keyboard aftertouch – all at
the same time.
The four MORPH buttons, VELOCITY, WHEEL, PEDAL and
A TOUCH, represent the four available continuous morph
sources: keyboard velocity, the modulation wheel,
keyboard aftertouch, and control pedal.
There is also the Impulse Morph button, which is an
instant morph source, described below.
a Morph is set up by holding down one of the Morph buttons, while at
the same time moving a parameter control (for example a knob or a leD
fader) from the point where the morph should start to the point where it
should end. It is a good practice to have the control set to the desired
start position before pressing down the morph assign button. The dis-
play will show the start and stop values as the morph is set up.
Multiple parameters can be adjusted while pressing down a Morph
assign button, and additional morph destinations can be added after a
morph has been assigned.
To CLEAR all morphs assigned to one of the morph sources, press Shift
and the corresponding Morph button.
To clear a single morph, press down the corresponding Morph button,
press Shift and turn the knob for the parameter that should be cleared.
Morphable Parameters
Glide layer level
arp/Gate Rate layer Pan
arp/Gate Range/env amp env attack
lfO Rate amp env Decay
lfO amount amp env Sustain
Osc Mod env attack amp env Release
filter Resonance
filter env amount
effects Rate
effects amount
Drive amount
Delay Rate/Time