Mitsubishi MOTORS Triton Owner's Manual

Table of Contents

Quick Links

Download this manual

Foreword

Thank you for selecting a MITSUBISHI MOTORS product as your

new vehicle.

This owner's manual will add to your understanding and full enjoy-

ment of the many fine features of this vehicle.

It contains information prepared to acquaint you with the proper way

to operate and maintain your vehicle for the utmost in driving pleasure.

MITSUBISHI MOTORS CORPORATION reserves the right to make

changes in design and specifications and/or to make additions to or

improvements in this product without obligation to install them on

products previously manufactured.

It is an absolute requirement for the driver to strictly observe all laws

and regulations concerning vehicles.

This owner's manual has been written in compliance with such laws

and regulations, but some of the contents may become contradictory

with later amendment of the laws and regulations.

If your vehicle is equipped with any locally produced part, the operat-

ing procedure, specifications, maintenance intervals and other contents

found in this owner's manual may not sometimes apply to it.

Please leave this owner's manual in this vehicle at time of resale. The

next owner will appreciate having access to the information contained

in this owner's manual.

Throughout this owner's manual the words WARNING and

CAUTION appear. These serve as reminders to be especially care-

E09200108221

ful. Failure to follow instructions could result in personal injury or

damage to your vehicle.

Indicates a strong possibility of severe personal injury or death if

instructions are not followed.

Means hazards or unsafe practices that could cause minor per-

sonal injury or damage to your vehicle.

You will see another important symbol:

Gives helpful information.

*: Indicates optional equipment.

It may differ according to the sales classification; refer to

the sales catalogue.

Abbreviations used in this owner's manual:

M/T: Manual Transmission

A/T: Automatic Transmission

The symbol used on the vehicles:

: See owner's manual

 Please understand that the information in this manual may

not pertain exactly to your vehicle due to differences in

equipment specifications, etc.

 If you have any questions, please contact the sales staff in

charge.

Table of Contents

Chapters

Table of Contents

Troubleshooting

Need help?

Do you have a question about the Triton and is the answer not in the manual?

Questions and answers

July 15, 2025

when do triton airbags deploy

Elpianus

May 13, 2025

Modul apa yg ada di balik saklar wiper,apakah modul terhubung ke sistem lampu kepala

Summary of Contents for Mitsubishi MOTORS Triton

Page 1 CAUTION appear. These serve as reminders to be especially care- E09200108221 ful. Failure to follow instructions could result in personal injury or Thank you for selecting a MITSUBISHI MOTORS product as your damage to your vehicle. new vehicle. This owner’s manual will add to your understanding and full enjoy- ment of the many fine features of this vehicle.
Page 2 Table of contents Overview/Quick guide General information Locking and unlocking Seat and seat belts Instruments and controls Starting and driving For pleasant driving For emergencies Vehicle care Maintenance Specifications Alphabetical index...
Page 3 Instruments and Controls (Driver’s area) Instruments and Controls (Driver’s area) E08500103017 Combination headlamps and dipper switch P.5-53 Automatic High Beam (AHB) switch* P.5-56 Turn-signal lever P.5-60 Cruise control switches* P.6-76 Front fog lamp switch*P.5-61 Instruments P.5-2 Ignition switch* P.6-13 Engine switch* P.6-14 Shift paddles* P.6-31 Electric remote-controlled outside rear-view mirrors* P.6-9...
Page 4 Instruments and Controls Instruments and Controls E08500103020 Audio* P.7-17, 7-38 Type 1 DVD AUDIO* Rear window demister switch* P.5-65 Refer to the separate owner’s manual Cooler* P.7-4 Steering wheel height and reach adjustment lever P.6-7 Air conditioning* P.7-7 Centre ventilators P.7-2 Supplemental restraint system (SRS) - airbag Hazard warning flasher (for front passenger’s seat)*...
Page 5 Instruments and Controls Type 2 Audio* P.7-17, 7-38 Rear window demister switch P.5-65 DVD AUDIO*, Mitsubishi Multi Entertainment Air conditioning P.7-7 System (MMES)* Steering wheel height and reach Refer to the separate owner’s manual adjustment lever P.6-7 Centre ventilators P.7-2 Supplemental restraint system (SRS) - airbag Centre console under tray P.7-73, 7-74 (for front passenger’s seat) P.4-16, 4-19...
Page 6 Interior Interior E08500202431 Single cab Room lamp P.7-71, 10-24, 10-33 Inside rear-view mirror P.6-8 Sun visors P.7-67 Seat belts P.4-6 Front seats P.4-2 Jack handle P.8-6 Head restraints P.4-4 Tools P.8-6 Jack P.8-6 Overview/Quick guide...
Page 7 Interior Club cab Room lamp (front)* P.7-71, 10-24, 10-32 Hands-free microphone* Map lamps* P.7-71, 7-73, 10-24, 10-32 Refer to the separate owner’s manual Sunglasses holder* P.7-73, 7-76 Room lamp (rear) P.7-71, 10-24, 10-33 Inside rear-view mirror P.6-8 Sun visors P.7-67 Card holder* P.7-67 Vanity mirror* P.7-67 Seat belts P.4-6...
Page 8 Interior Double cab Room lamp (front) P.7-71, 10-24, 10-32 Hands-free microphone* Map lamps P.7-71, 7-73, 10-24, 10-32 Refer to the separate owner’s manual Sunglasses holder P.7-73, 7-76 Rear circulator* P.7-14 Rear circulator switch* P.7-15 Room lamp (rear) P.7-71, 10-24, 10-33 Inside rear-view mirror P.6-8 Rear personal lamps* P.7-71, 7-73, 10-24, 10-33 Rear circulator switch* P.7-14...
Page 9 Exterior - front Exterior - front E08500403485 Single cab Antenna P.7-62 Wiper and washers P.5-61, 10-15 Fuel tank filler door* P.2-2 Bonnet P.10-3 Engine compartment P.10-2, 11-13 Locking and unlocking P.3-16 Keyless entry system* P.3-4 Outside rear-view mirrors P.6-9 Side turn-signal lamps P.5-60, 10-22 Headlamps, low beam P.5-53, 10-22, 10-24 Headlamps, high beam...
Page 10 Exterior - front Club cab Antenna P.7-63 Wiper and washers P.5-61, 10-15 Fuel tank filler door P.2-2 Bonnet P.10-3 Engine compartment P.10-2, 11-13 Locking and unlocking P.3-16 Keyless entry system* P.3-4 Keyless operation system* P.3-8 Outside rear-view mirrors P.6-9 Side turn-signal lamps (on outside rear-view mirror)* P.5-60, 10-22 Side-view camera* P.6-112 Front-view camera* P.6-112...
Page 11 Exterior - front Double cab Antenna P.7-63 Sensor* [for Automatic High Beam (AHB) and Forward Collision Mitigation system (FCM)] Fuel tank filler door P.5-56, 6-80, 6-88 P.2-2 Rain sensor* P.5-62 Wiper and washers P.5-61, 10-15 Locking and unlocking P.3-16 Keyless entry system P.3-4 Front-view camera* P.6-112 Keyless operation system* P.3-8 Outside rear-view mirror P.6-9...
Page 12 Exterior - rear Exterior - rear E08500403498 Single cab Tyre inflation pressures P.10-12 Changing tyres P.8-10 Tyre rotation P.10-13 Snow tyres P.10-14 Tyre chains P.10-14 Rear gate P.3-19 Tail lamps P.5-53, 10-22, 10-30 Stop lamps P.10-22, 10-30 Licence plate lamp P.5-53, 10-22, 10-31 Rear turn-signal lamps P.5-60, 10-22, 10-30 Spare wheel P.8-11...
Page 13 Exterior - rear Club cab High-mounted stop lamp* P.10-22 Tyre inflation pressures P.10-12 Changing tyres P.8-10 Rear-view camera* P.6-109 Tyre rotation P.10-13 Multi around monitor* P.6-112 Snow tyres P.10-14 Tyre chains P.10-14 Tail lamps P.5-53, 10-22 Rear gate P.3-19 Stop lamps P.10-22 Rear turn-signal lamps P.5-60, 10-22, 10-30 Licence plate lamp P.5-53, 10-22, 10-31...
Page 14 Exterior - rear Double cab Blind Spot Warning lamp* P.6-95 High-mounted stop lamp P.10-22 Rear-view camera* P.6-109 Multi around monitor* P.6-112 Tyre inflation pressures P.10-12 Changing tyres P.8-10 Tyre rotation P.10-13 Rear gate P.3-19 Snow tyres P.10-14 Tyre chains P.10-14 Tail lamps P.5-53, 10-22 Stop lamps P.10-22 Ultrasonic misacceleration Mitigation Sys-...
Page 15 Quick guide Refer to “Keyless entry system” on page Refer to “keyless operation system” on Quick guide 3-4. page 3-8. For vehicles equipped with the mirror retrac- E08500500010 tor switch, the outside rear-view mirrors can Around the driver’s seat Lock and unlock the doors be retracted and extended automatically if E08500802235 you press the LOCK switch (1) or UNLOCK...
Page 16 Quick guide 1-Wiper and washer switch  Vehicles equipped with rain sensor 2-Steering wheel height and reach adjustment  Except for vehicles equipped with 1. Release the lever while holding the steer- ing wheel up. rain sensor 2. Adjust the steering wheel to the desired position.
Page 17 Quick guide B- Release 3-Turn-signal lever Type 2 *: Vehicles equipped with the reach adjustment The turn-signal lamps flash when the lever is operated. Refer to “Steering wheel height and reach adjustment” on page 6-7. 3-Combination headlamps Rotate the switch to turn on the lamps. Type 1 All lamps off With the ignition switch or the...
Page 18 Quick guide 5-Electric remote-controlled out- 6-Fuel tank filler door release side rear-view mirrors lever Open the fuel tank filler door. To adjust the mirror position The fuel tank filler is located on the rear left side of your vehicle. Type 1 OFF- The indicator lamp on the engine switch turns off.
Page 19 Quick guide 7-Electric window control Automatic transmission Sports Selector lever positions Mode 6A/T Press the switch down for opening the win- “P” PARK E08501001686 dow, and pull the switch for closing. This position locks the transmission to pre- Selector lever operation vent the vehicle from moving.
Page 20 Quick guide 4-wheel drive operation E08502000123 Road conditions Driving mode Dry paved road Packed snow Deep snow or Gravel road Sandy road Rocky road and highway road muddy road Easy Select 4WD 4H or 4L 4H or 4L 4H or 4L 4H or 4L (...
Page 21 Quick guide 4- Forward Collision Mitigation system Multi information display Type 2 (FCM) OFF indicator display* E08501201604  P.6-80 Always stop the vehicle in a safe place before Ultrasonic misacceleration Mitigation operating. System (UMS) OFF indicator display* The following information is included on the ...
Page 22: Table Of Contents
General information Fuel selection ...................2-2 Filling the fuel tank ................2-2 Entering or leaving the vehicle* ............2-4 Installation of accessories ..............2-4 Modification/alterations to the electrical or fuel systems ....2-5 Genuine parts ...................2-5 Safety and disposal information for used engine oil .......2-6 Event Data Recording ..............2-6...
Page 23: Fuel Selection
 If you continuously use fuel that contains ised MITSUBISHI MOTORS dealer. more than 7 % bio-diesel, the impurities in  Do not move away from the fuel tank filler the bio-diesel could precipitate.
Page 24 Filling the fuel tank 3. [Vehicles for Type 1, 2] Refueling Type 3 Open the fuel tank filler tube by slowly turning the fuel cap anticlockwise. 1. Before filling with fuel, stop the engine. 2. The fuel tank filler is located on the rear Type 1 left side of your vehicle.
Page 25: Entering Or Leaving The Vehicle
[Vehicles for Type 3] E00200302648 To close, turn the fuel cap slowly clock- Before fitting any accessories, please consult wise until you hear clicking sounds, then your authorised MITSUBISHI MOTORS turn the key clockwise to lock the fuel dealer. cap. CAUTION ...
Page 26: Modification/Alterations To The Electrical Or Fuel Systems
MITSUBISHI MOTORS has gone to great available in the market, it is not possible, not lengths to bring you a superbly crafted vehi- only for MITSUBISHI MOTORS but also an cle offering the highest quality and dependa- authorised MITSUBISHI MOTORS dealer, bility.
Page 27: Safety And Disposal Information For Used Engine Oil
PARTS.  EDR data are recorded by your vehicle only dren. At the MITSUBISHI MOTORS dealer you if a non-trivial crash situation occurs; no data can also get appropriate advice and the are recorded by the EDR under normal driv- assembling of Genuine Parts will be handled ing conditions and no personal data (e.g.,...
Page 28 Locking and unlocking Keys ....................3-2 Key number tag ................3-2 Electronic immobilizer (Anti-theft starting system)*.......3-3 Keyless entry system* ..............3-4 Keyless operation system* ...............3-8 Doors ....................3-16 Central door locks*.................3-17 “Child-protection” rear doors (Double cab) ........3-19 Rear gate ..................3-19 Electric window control ..............3-21...
Page 29: Keys
 If you lose one of them, contact an author- E00300104713 key (except for the emergency key) is a pre- ised MITSUBISHI MOTORS dealer as soon Keyless entry key cision electronic part with a built-in signal as possible to prevent theft.
Page 30: Electronic Immobilizer (Anti-Theft Starting System)
 [Vehicles with keyless operation system] If the engine does not start, contact an  [Vehicles without keyless operation system] authorised MITSUBISHI MOTORS dealer. In the following cases, the vehicle may not be able to receive the registered ID code from the registered key and engine may not start.
Page 31: Keyless Entry System
If you need an extra spare key, take your To unlock Keyless entry system vehicle and all the keys to an authorised MITSUBISHI MOTORS dealer. All the keys E00300305161 Press the UNLOCK switch (2). All the doors have to be re-registered in the immobilizer computer unit.
Page 32 For further information, please contact an • The confirmation function (this indicates To retract authorised MITSUBISHI MOTORS dealer. locking or unlocking of the doors with the If you replace the battery yourself, refer to blink of the turn-signal lamps) can be deac- Locking the doors using the LOCK switch “Procedure for replacing the key battery”...
Page 33 Keyless entry system* NOTE NOTE WARNING • Automatically extend when the driver’s • Deactivate the automatic extension func- • This product contains coin type battery. door is closed, and then the following oper- tion. If a coin type battery is swallowed, it can ation is performed.
Page 34 5. Install a new battery with the + side (B)  You may purchase a replacement battery at an electric appliance store. Keyless entry key  An authorised MITSUBISHI MOTORS + side dealer can replace the battery for you if you prefer.
Page 35: Keyless Operation System
(The keyless operation sys- sure to check that you have the keyless opera- tion key. tem can be used as a keyless entry system.) Please consult an authorised MITSUBISHI MOTORS dealer. Locking and unlocking...
Page 36  The keyless operation key uses an ultra-weak ual or have it replaced an authorised unlocking the doors electromagnetic wave. In the following MITSUBISHI MOTORS dealer. cases, the keyless operation system may not Refer to “Procedure for replacing the key E00306201832 operate properly or may be unstable.
Page 37 Keyless operation system* NOTE To operate using the keyless operation function  Locking and unlocking operate only when you press a door switch that detects the key- E00305802841 less operation key.  Operation may not be possible if you are too close to the front door, door window.
Page 38  Functions can be modified as stated below. operation function. Refer to “Starting and For further information, please contact an driving: Outside rear-view mirrors” on page authorised MITSUBISHI MOTORS dealer. 6-9. • Activating the operation confirmation func-  The keyless operation function does not...
Page 39 Keyless operation system* 2- Unlock Locking and unlocking the door Turning the emergency key in the forward direction locks the door, and turning it in the rear direction unlocks the door. Also refer to “Locking and unlocking: Doors” on page 3-16.
Page 40 Keyless operation system* TYPE 1 TYPE 2 Item Note (Solution) Display Buzzer Indicator Buzzer Fall of battery Inner buzzer No sounds The battery starts to run out, the warning is activated. （The voltage sounds once warning is not activated if the battery is completely dead.） Blinks Key not Inner buzzer...
Page 41 For further information, please contact an authorised MITSUBISHI MOTORS dealer. • Even if you have the keyless operation key within the...
Page 42 Keyless operation system* TYPE 1 TYPE 2 Item Note (Solution) Display Buzzer Indicator Buzzer Key lock-in Inner buzzer Outer buzzer • When the operation mode is in OFF, if you close all the prevention sounds once sounds doors with the keyless operation key left in the vehicle and system Outer buzzer approxi-...
Page 43: Doors
Doors 2- Unlock Doors NOTE  The driver’s door can be opened without NOTE E00300403722 using the lock knob by pulling on the inside CAUTION  On vehicles with central door locks, when door handle. locking or unlocking with the key, all doors On vehicles with central door locks, all other ...
Page 44: Central Door Locks
Central door locks* To open or close the rear door WARNING Central door locks (Club cab)  When opening the rear door, confirm that E00300803322 the occupant of the front seat has taken off E00313800022 the seat belt before opening the rear door. NOTE You can open or close the rear door while the If you open the rear door with the front...
Page 45  When the vehicle-speed sensitive auto- matic door lock/Impact-sensitive unlock mechanism may not operate in the follow- ing conditions, have the vehicle inspected at an authorised MITSUBISHI MOTORS dealer immediately. • The door does not lock automatically 1- Lock 1- Lock...
Page 46: Child-Protection" Rear Doors (Double Cab)
“Child-protection” rear doors (Double cab) NOTE “Child-protection” rear CAUTION doors (Double cab)  These functions are activated when the vehi-  When driving with a child in the rear seat, cle is shipped from the factory. If you wish to please use the child protection to prevent E00300902140 activate or deactivate these functions, please...
Page 47 Rear gate To swing down The rear gate can be swung down in two stages except some models. To lower it to the second stage, proceed as follows: CAUTION  On vehicles with the rear bumper, never swing down the rear gate because the rear gate could be damaged.
Page 48: Electric Window Control
Electric window control [Type 2] Electric window control WARNING If the switch for the driver’s window is fully  Before operating the electric window con- pressed down/pulled up, the door window E00302201658 trol, make sure that nothing is capable of The electric windows can only be operated automatically opens/closes completely.
Page 49 Electric window control NOTE WARNING WARNING  Repeated operation with the engine stopped  A child may tamper with the switch at the  If the battery terminals are disconnected will run down the battery. Operate the win- risk of its hands or head being trapped in or the fuse for electric window is replaced, dow switches only while the engine is run- the window.
Page 50 Electric window control NOTE  If the safety mechanism is activated five or more times in a row, the safety mechanism will be cancelled and the door window will not close correctly. In such a case, the following procedure should be implemented to rectify this situa- tion.
Page 52 Seat and seat belts Seat adjustment ................4-2 Front seats ..................4-2 Rear seat*..................4-3 Head restraints .................4-4 Seat belts ..................4-6 Pregnant women restraint ..............4-9 Seat belt pre-tensioner system and force limiter system* ....4-9 Child restraint ................4-10 Seat belt inspection ................4-16 Supplemental restraint system (SRS)-airbag* ........4-16...
Page 53: Seat Adjustment
Seat adjustment Seat adjustment WARNING CAUTION  To minimize the risk of personal injury in  When sliding or reclining the seat rearward, E00400302060 the event of a collision or sudden braking, pay careful attention to the rear seat passen- Adjust the driver’s seat so that you are com- the seatbacks should always be in the gers.
Page 54: Rear Seat
Rear seat* 3- To adjust seat cushion height (driver’s 4- To adjust seat cushion angle side only)* Operate the switch as indicated by the Turn the dial and adjust the seat cush- arrows and adjust the seat cushion ion height to the desired position. angle to the desired position.
Page 55: Head Restraints
Head restraints Armrest Head restraints Type 1 E00401701774 E00403302931 To use the armrest, fold it down. WARNING To return to the original position, push it  Driving without the head restraints in backward until it is flush with the seat. place can cause you and your passengers serious injury or death in an accident.
Page 56 Head restraints in the direction of the arrow. After adjust- To remove ment, push the head restraint downward and make sure that it is locked. Lift the head restraint with the height adjust- ing knob (A) pushed in. To install Confirm that the head restraint is facing the correct direction, and then insert it into the seatback while pressing the height adjusting...
Page 57: Seat Belts
Seat belts CAUTION WARNING  Confirm that the height adjusting knob (A) is  Seat belts should always be worn by every correctly adjusted as shown in the illustra- adult who drives or rides in this vehicle, tion, and also lift the head restraints to and by all children who are large enough ensure that they do not come out of the seat- to wear seat belts properly.
Page 58 Seat belts 2. Insert the latch plate into the buckle until WARNING a “click” is heard.  Always adjust the seat belt to a snug fit.  Always wear the lap portion of the belt over your hips. 3-point type seat belt (with emergency locking mechanism) E00404902921 This type of belt requires no length adjust-...
Page 59 Seat belts Seat belt reminder WARNING  Do not install any accessory or sticker that E00409802781 makes the lamp difficult to see. Type 1 NOTE  If the seat belt subsequently remains unfas- tened, the warning lamp and the tone will issue further warnings each time the vehicle starts moving from a stop.
Page 60: Pregnant Women Restraint
 If you need to scrap the vehicle, please con- mode is under the following conditions, if plate into the buckle until a “click” is heard. sult an authorised MITSUBISHI MOTORS there is a frontal impact or a side impact dealer. It is important to do so because unex-...
Page 61: Child Restraint
Child restraint SRS warning WARNING Type 1  When possible, put children in the rear E00405900360 seat. Accident statistics indicate that chil- The same warning lamp/display is shared by dren of all sizes and ages are safer when the SRS airbags and the pre-tensioner seat properly restrained in the rear seat rather belts.
Page 62 Child restraint WARNING Instruction:  On vehicles with an airbag for the front  For small infants, an infant carrier should passenger, REARWARD FACING be used. For small children whose height CHILD RESTRAINT must NOT be used when seated allows the shoulder belt to lie in the front passenger seat as it places an in contact with the face or the throat, a infant too close to the passenger airbag.
Page 63 Child restraint WARNING Child restraint anchorage Tether anchor strap installation points (Double cab)  When installing a child restraint system, refer to the instructions provided by the WARNING E00406902198 manufacturer of the restraint system.  Child restraint anchorages are designed to Failure to do so can result in severe or When fitting a child restraint, always follow withstand only those loads imposed by...
Page 64 Child restraint 4. Open the inner cover. Installing a child restraint sys- Child restraint system with tem to the lower anchorage ISOFIX mountings (Double (ISOFIX child restraint mount- cab) ings of Double cab) E00409001656 E00408902219 The child restraint system is designed only for seats that incorporate lower anchorages.
Page 65 Child restraint CAUTION  Do not remove the head restraint when installing a booster cushion. A: Child restraint system connectors A: Vehicle seat cushion B: Vehicle seatback C: Lower anchorage 3. Open the gap a little between the seat To install D: Connector cushion (A) and the seatback (B) with your hand to locate the lower anchorages...
Page 66 Child restraint 3. Remove all slack of a lap belt by pulling Installing a child restraint sys- the webbing through the belt’s adjustment tem to a 3-point type seat belt feature. (with emergency locking mech- 3-point type seat belt requires no length adjustment, remove all slack by using the anism) or a lap belt locking clip (A).
Page 67: Seat Belt Inspection
MITSUBISHI MOTORS dealer. Failure certain moderate-to-severe side impact colli- because this affects their characteristics. to have an authorised MITSUBISHI sions. MOTORS dealer perform the work could...
Page 68 Supplemental restraint system (SRS)-airbag* occupants, including the passengers as well windows after airbag deployment, if safe to as the driver, must wear their seat belts. do so. The airbags deflate very rapidly after deploy- ment, so there is little danger of obscured How the supplemental restraint vision.
Page 69 Supplemental restraint system (SRS)-airbag* WARNING Type 1  Place all infants and small children in the rear seat and properly restrained using an appropriate child restraint system. The rear seat is the safest for infants and children. (Double cab) WARNING Type 2 ...
Page 70 Supplemental restraint system (SRS)-airbag* Driver’s and front passenger’s airbag system E00407401874 The driver’s airbag is located under the pad- ded cover in the middle of the steering wheel. The front passenger’s airbag is contained in the instrument panel above the glove box. The driver’s airbag and the front passenger’s airbag are designed to inflate at the same time even if the passenger seat is not occupied.
Page 71 Supplemental restraint system (SRS)-airbag* Because frontal collisions can easily move you out of position, it is important to always properly wear your seat belts. Your seat belts will help keep you a safe distance from the steering wheel and instrument panel during the initial stages of airbag deployment.
Page 72 Supplemental restraint system (SRS)-airbag* WARNING WARNING  Do not attach anything to the steering  Do not attach additional keys or accesso- wheel’s padded cover, such as badges or ries (hard, pointed or heavy objects) to the accessories. It might strike and injure an ignition key.
Page 73 Supplemental restraint system (SRS)-airbag* The label shown here is attached to the seat- WARNING backs with a side airbag.  Right after the airbag inflation, several airbag system components will be hot. Do not touch these components. There is a danger of being burnt.
Page 74 Supplemental restraint system (SRS)-airbag* vehicle body. Examples of some typical con- 5- Vehicle rolls onto its side or roof ditions are shown in the illustration. Because the side airbags and curtain airbags do not protect the occupant in all types of side collisions, be sure to always properly wear your seat belts.
Page 75 Supplemental restraint system (SRS)-airbag* Because the side airbags and curtain airbags WARNING do not protect the occupant in all types of col-  Do not allow any rear seat occupant to lisions, be sure to always properly wear your hold onto the seatback of either front seat, seat belts.
Page 76 SRS inspected onds and then go out. This is normal and by an authorised MITSUBISHI MOTORS means the system is working properly. dealer. Seat and seat belts...
Page 77 Supplemental restraint system (SRS)-airbag* NOTE  If your vehicle has to be scrapped, do this in line with local legislation and contact an authorised MITSUBISHI MOTORS dealer to safely dismantle the airbag system. 4-26 Seat and seat belts...
Page 78 Instruments and controls Instruments ..................5-2 Multi information display - Type 1 ..........5-3 Multi information display - Type 2 ..........5-18 Indicator lamp, warning lamp, and information screen display list (multi information display - Type 1) ....5-27 Indicator and warning lamps (multi information display - Type 2) ..........5-48 Indicator lamps ................5-49 Warning lamps ................5-50 Information screen display (Vehicles equipped...
Page 79: Instruments
Instruments 2- Multi information display (Type 1: Instruments Meter illumination control - Color liquid crystal display type)  Type 1 E00500103053 P.5-3 Information screen display list (Type 1) E00531301116 Type 1  P.5-28 Each time you press the rheostat illumination Multi information display (Type 2: button, there is a sound and the brightness of Mono-color liquid crystal display type)
Page 80: Multi Information Display - Type 1
Multi information display - Type 1 [When the ignition switch or the operation [When the ignition switch or the operation NOTE mode is OFF] mode is ON]  The brightness level of the instruments is stored when the ignition switch is turned off or the operation mode is put in OFF.
Page 81 Multi information display - Type 1 8-Selector lever position display*  information display by operating the multi Information screen (when the information display switch. P.6-30 ignition switch or the operation 9-Engine coolant temperature display mode is OFF)  P.5-7 10-Odometer  P.5-8 E00520202125 11-Fuel remaining display ...
Page 82 Multi information display - Type 1 1- Tripmeter  P.5-8 Information screen (when the Information screen (when the 2- Tripmeter  P.5-8 ignition switch is turned from ignition switch or the operation 3- Driving range display  P.5-10 the “LOCK” position to the mode is ON) ECO drive assist display ...
Page 83 Multi information display - Type 1 NOTE “ ”: Press lightly. To return to the screen displayed before the warning display “ ”: Press for approximately 2 seconds or  While driving, the function setting screen is not displayed even if you operate the multi more.
Page 84 Multi information display - Type 1 When the cause of the warning display is Pay careful attention to the engine coolant NOTE temperature display while you are driving. eliminated, the mark goes out automati-  It may take several seconds to stabilise the cally.
Page 85 Displays the approximate time until the next periodic inspection recommended It is possible to measure two currently MITSUBISHI MOTORS. “---” is displayed Outside temperature display travelled distances, from home using trip- when the inspection time has arrived. meter and from a particular point on...
Page 86 Please consult an authorised tion display switch a few times, the infor-  Depending on the vehicle specifications, the MITSUBISHI MOTORS dealer. mation screen switches to the service displayed time may differ from the next peri- reminder display screen.
Page 87  If you accidentally reset the display, we rec- drive). When the driving range falls below ommend you to consult an authorised play approximately 50 km (30 miles), “---” is dis- MITSUBISHI MOTORS dealer. played. E00531201157 Refuel as soon as possible. This displays the average fuel consumption from the last reset to the present time.
Page 88 Multi information display - Type 1 The reset mode conditions for the average NOTE NOTE fuel consumption display can be switched  The memory of the auto reset mode or man-  The average speed display can be reset sepa- between “Auto reset”...
Page 89 Multi information display - Type 1 momentary fuel consumption is displayed Auto Stop & Go (AS&G) moni- with a green bar graph. ECO drive level Be conscious of maintaining the momentary fuel consumption above the average fuel con- E00531101097 The accumulated time the engine has been sumption, driving with the better fuel con- stopped by Auto Stop &...
Page 90 Multi information display - Type 1 The display shows the overall ECO score the 2. Lightly press the multi information dis- function has counted from the time when the play switch a few times to switch the ignition switch is turned to “ON” to the time information screen to the function setting when it is turned to “LOCK”...
Page 91 Multi information display - Type 1 Refer to “Changing the temperature unit” 1. Press and hold the multi information dis- Turn the ignition switch from the “ACC” on page 5-15. play switch for approximately 2 seconds or “LOCK” position to the “ON” position. Refer to “Changing the display language”...
Page 92 Multi information display - Type 1 [For vehicles equipped with the keyless 2. Lightly press the multi information dis- Distance Speed Fuel con- operation system] play switch to select (driving (average sumption The operation mode is in ACC or OFF for “AVG UNIT (fuel consumption display range) speed)
Page 93 Multi information display - Type 1 NOTE NOTE NOTE  The temperature value on air conditioning  If “---” is selected in the language setting, a  The operation sound setting only deactivates panel is switched in conjunction with outside warning message is not displayed when there the operation sound of the multi information temperature display unit of the multi infor-...
Page 94 Multi information display - Type 1 5. Press and hold the multi information dis- 1. Press and hold the multi information dis- Changing the momentary fuel con- play switch for approximately 2 seconds play switch for approximately 2 seconds sumption display or more, the setting is changed to the or more to switch from the setting mode E00529201408...
Page 95 Multi information display - Type 2 Multi information display - NOTE Type 2  When the ignition switch or the operation mode is OFF, the selector lever position dis- E00519903129 play, fuel remaining display, engine coolant Always stop the vehicle in a safe place before temperature display and frozen road warning operating.
Page 96 Multi information display - Type 2 Information display E00528201371 Each time you lightly press the multi information display switch (A), the display switches in the following order. 1- Odometer  P.5-20 5- Driving range display  P.5-20 8- Service reminder (distance)  P.5-23 9- Service reminder (month) ...
Page 97 Multi information display - Type 2 Odometer NOTE NOTE  When disconnecting the battery terminal, the  You can adjust to 8 different levels respec- E00527801123 tively for when the position lamps are illumi- The odometer indicates the distance travelled. memory of tripmeter nated and when they are not.
Page 98 Multi information display - Type 2 NOTE NOTE NOTE  When you refuel, the driving range display is  The average fuel consumption display can be  The display setting can be changed to the updated. reset separately for the auto reset mode and preferred units (°C or °F).
Page 99 Multi information display - Type 2 CAUTION Fuel remaining display Fuel remaining warning display  There is a danger the road might be icy, even E00522402381 E00522201816 when this symbol is not flashing, so please If the remaining fuel level is approximately The fuel remaining display indicates the fuel take care when driving.
Page 100 Please consult an authorised original indication.) In addition, the display settings for the next MITSUBISHI MOTORS dealer. periodic inspection time can be modified. 3. Lightly press the multi information dis- 3. After your vehicle is inspected at an...
Page 101 Multi information display - Type 2 2. Each time you press the multi information Changing the function settings display switch for 2 seconds or more on E00522700595 driving range display, you can switch The “Average fuel consumption reset mode”, reset mode for average fuel consumption. “Fuel consumption unit”...
Page 102 Multi information display - Type 2 [For vehicles equipped with the keyless 3. Press and hold the multi information dis- NOTE operation system] play switch to switch in sequence from  The average fuel consumption display can be “km/L”  “L/100 km”  “mpg”  Change the operation mode from ACC reset separately for the auto reset mode and or OFF to ON.
Page 103 Multi information display - Type 2 Distance Fuel consumption (driving range) km/L L/100 km mile (s) Changing the temperature unit E00523102082 The display unit for outside temperature can be switched. 1. When you lightly press the multi informa- tion display switch a few times, the infor- mation display switches to the outside temperature display.
Page 104: Indicator Lamp, Warning Lamp, And Information Screen Display List (Multi Information Display - Type 1)
Indicator lamp, warning lamp, and information screen display list (multi information display - Type 1) Indicator lamp, warning lamp, and information screen display list (multi information display - Type 1) E00523701254 Indicator and warning lamp list E00523802731 1- Position lamp indicator lamp  P.5-49 11- LED headlamp warning lamp P.5-52 6- Rear differential lock indicator lamp* P.6-52...
Page 105 • An extremely strong electromagnetic wave is received from a source such as an illegal radio set, a spark from a wire, or a radar station. • Abnormal voltage or a static electricity discharge is generated by the operation of installed electrical equipment (including after-market parts). If the warning display appears many times, consult an authorised MITSUBISHI MOTORS dealer. 5-28...
Page 106  There is a fault in the electrical system.  Immediately stop the vehicle in a safe place and consult an authorised MITSUBISHI MOTORS dealer.  There is a fault in the keyless operation Refer to “Keyless operation system” on page system.
Page 107 5-7.  There is a fault in the fuel system.  Have your vehicle inspected at an author- ised MITSUBISHI MOTORS dealer.  You are driving with the parking brake still  Release the parking brake. Refer to “Brake applied.
Page 108  Immediately stop the vehicle in a safe fallen to a low level. place and consult an authorised  There is a fault in the brake system. MITSUBISHI MOTORS dealer. Refer to “Brake warning display” on page 5-52.  There is a fault in the charging system.
Page 109  There is a fault in the steering wheel lock.  Immediately stop the vehicle in a safe place and consult an authorised MITSUBISHI MOTORS dealer. Refer to “Steering wheel lock” on page 6-16.  The steering wheel is locked.
Page 110 Refer to “When a malfunction occurs in the A/T” on page 6-33.  There is a fault in the A/T.  Have your vehicle inspected at an author- ised MITSUBISHI MOTORS dealer, immediately. Refer to “When a malfunction occurs in the A/T” on page 6-33.
Page 111 “4HLc”  “4LLc”.  There is a fault in the Easy Select 4WD.  Have your vehicle inspected at an author- ised MITSUBISHI MOTORS dealer as soon as possible. Refer to “Drive mode indicator display and 2WD/4WD operation indicator display” on page 6-41.
Page 112  There is a fault in the rear differential lock  Have your vehicle inspected at an author- system. ised MITSUBISHI MOTORS dealer as soon as possible. Refer to “The rear differential lock indica- tor lamp/display” on page 6-52.
Page 113  There is a fault in the hill start assist.  Have your vehicle inspected at an author- ised MITSUBISHI MOTORS dealer. Refer to “Warning lamp/display” on page 6-66.  There is a fault in the active stability &...
Page 114  There is a fault in the Forward Collision  Have your vehicle inspected at an author- Mitigation system (FCM). ised MITSUBISHI MOTORS dealer. Refer to “When a problem is detected” on page 6-86.  The Forward Collision Mitigation system Refer to “When a problem is detected”...
Page 115 Indicator lamp, warning lamp, and information screen display list (multi information display - Type 1) Screen Cause Solution (Reference)  When the Forward Collision Mitigation Refer to “FCM and UMS ON/OFF switch” on system (FCM) is ON, if the drive mode- page 6-85.
Page 116 6-94.  The Ultrasonic misacceleration Mitigation  Immediately have your vehicle inspected at System (UMS) does not operate normally an authorised MITSUBISHI MOTORS because there are some malfunctions in the dealer. sensor or the system. Refer to “When there is a malfunction in the system or the sensor”...
Page 117 Indicator lamp, warning lamp, and information screen display list (multi information display - Type 1) Screen Cause Solution (Reference)  The Ultrasonic misacceleration Mitigation Refer to “Ultrasonic misacceleration Mitiga- System (UMS) is activated. tion System (UMS)” on page 6-90.  When the Ultrasonic misacceleration Miti- Refer to “When the UMS is not available”...
Page 118 Indicator lamp, warning lamp, and information screen display list (multi information display - Type 1) Screen Cause Solution (Reference)  When the Ultrasonic misacceleration Miti- Refer to “When the UMS is not available” on gation System (UMS) is ON, if the rear dif- page 6-95.
Page 119  The Blind Spot Warning (BSW) does not  Have your vehicle inspected at an author- operate normally because there are some ised MITSUBISHI MOTORS dealer as malfunctions in the sensor or the system. soon as possible. Refer to “When there is a malfunction in the system or the sensor”...
Page 120 Refer to “Engine overheating” on page 8-4.  There is a fault in the sensor.  We recommend you to consult an author- ised MITSUBISHI MOTORS dealer. Refer to “Forward Collision Mitigation system (FCM): When a problem is detected” on page 6-86.
Page 121 Indicator lamp, warning lamp, and information screen display list (multi information display - Type 1) Screen Cause Solution (Reference)  More than specified limit water has accu-  Refer to “Removal of water from the fuel mulated in the fuel filter. filter”...
Page 122 Indicator lamp, warning lamp, and information screen display list (multi information display - Type 1) Screen System operation status Reference  When “ROCK” mode of Off Road mode is Refer to “Control mode” on page 6-49. selected.  When “MUD/SNOW” mode of Off Road Refer to “Control mode”...
Page 123 Indicator lamp, warning lamp, and information screen display list (multi information display - Type 1) Screen System operation status Reference  When the Forward Collision Mitigation Refer to “FCM and UMS ON/OFF switch” on system (FCM) is activated or the timing of page 6-85.
Page 124 Indicator lamp, warning lamp, and information screen display list (multi information display - Type 1) The setting for rest interval can be changed. Screen Solution Stop the vehicle in a safe place, turn off the engine, and take a rest. Use this display as rough guide for taking rests during a long drive.
Page 125: Indicator And Warning Lamps (Multi Information Display - Type 2)
Indicator and warning lamps (multi information display - Type 2) Indicator and warning lamps (multi information display - Type 2) E00501504527 9- Cruise control indicator lamp*  17- For details, refer to “Electronic immo- 1- High-beam indicator lamp  P.5-49 P.6-77 bilizer (Anti-theft starting system)”...
Page 126: Indicator Lamps
Indicator lamps 22- Active Stability & Traction Control High-beam indicator lamp Diesel preheat indicator lamp (ASTC) OFF indicator lamp*  P.6-74 E00501801327 E00502301475 23- Supplemental restraint system (SRS) This indicates the glow plug This indicator lamp illumi- warning lamp*  P.4-25 preheat condition.
Page 127: Warning Lamps
Warning lamps NOTE Warning lamps CAUTION  When the engine is warm, the diesel preheat  In the situations listed below, brake perfor- E00502400147 indicator lamp does not come on even if the mance may be compromised or the vehicle ignition switch is placed in the “ON”...
Page 128 Immediately park your vehicle in a safe MITSUBISHI MOTORS dealer as soon as place and we recommend you to have it which monitors the emissions, possible.
Page 129: Information Screen Display (Vehicles Equipped With The Multi Information Display - Type 1)
Information screen display (Vehicles equipped with the multi information display - Type 1) This warning is displayed if you drive with CAUTION LED headlamp warning lamp the parking brake still applied. The warning  This warning lamp does not indicate the E00569000078 lamp in the instrument cluster also illumi- amount of oil in the crankcase.
Page 130: Combination Headlamps And Dipper Switch
Combination headlamps and dipper switch mation screen in the multi information dis- CAUTION CAUTION play. The warning lamp in the instrument  If the brake warning display is displayed and  If the warning is displayed while the engine cluster also illuminates. the brake warning lamp and the ABS warn- is running, immediately park your vehicle in ing lamp are illuminated at the same time,...
Page 131 Combination headlamps and dipper switch Type 1 Type 2 NOTE  The sensitivity of the automatic on/off con- Rotate the switch to turn on the lamps. Rotate the switch to turn on the lamps. trol can be adjusted. For further information, contact authorised MITSUBISHI...
Page 132 Combination headlamps and dipper switch Lamps (headlamps, fog lamp, NOTE Daytime running lamp etc.) auto-cutout function  The lamp auto-cutout function can also be E00530601545 disabled. E00532701827 The daytime running lamps comes on when For further information, we recommend you ...
Page 133 Combination headlamps and dipper switch 2. Press the AHB switch. Headlamp flasher E00506300199 The high beams flash when the lever is pulled slightly (2), and will go off when it is released. When the high beam is on, the high beam indicator lamp in the instrument cluster will illuminate.
Page 134 Combination headlamps and dipper switch NOTE Automatic switching conditions NOTE  You can switch the headlamp beams • Another vehicle crosses ahead of your vehi- E00551600105 (high/low) manually by operating the lever cle. The high beam headlamps illuminate when even if the AHB is working. ...
Page 135 • A light, which is similar to the headlamps • When the windscreen is replaced, use the NOTE or tail lamps, is shining around your vehi- MITSUBISHI MOTORS GENUINE parts.  If the sensor or its surrounding area becomes cle. extremely high temperature when parking •...
Page 136: Headlamp Levelling Switch
If the warning display does not disappear Double cab after waiting for a while, there is a possibility that the sensor has a malfunction. Contact an authorised MITSUBISHI MOTORS dealer for inspection of the sensor. Vehicle condition CAUTION  Always perform adjustments before driving.
Page 137: Turn-Signal Lever
Turn-signal lever : 1 person 2- Lane-change signals Hazard warning flasher :Full luggage loading When moving the lever to (2) slightly switch to change a lane, the turn-signal lamps Switch position 0- Driver only and indicator lamp in the instrument E00506602255 Switch position 4- Driver + Full luggage cluster will only flash while the lever is...
Page 138: Front Fog Lamp Switch
Front fog lamp switch* NOTE NOTE Windscreen wipers  On vehicles equipped with the emergency  The front fog lamps are automatically turned E00516902163 stop signal system, while the hazard warning off when the headlamps or tail lamps are lamps are blinking due to having manually turned off.
Page 139 Wiper and washer switch The wipers will automatically oper- ate depending on the degree of wet- ness on the windscreen. Slow Fast Rain sensor Can only be used when the ignition switch or the operation mode is in ON. If the lever is put in the “AUTO” position, the 1- Fast rain sensor (A) will detect the extent of rain 2- Slow...
Page 140 Wiper and washer switch CAUTION NOTE To adjust the sensitivity of the rain sensor  With the ignition switch or the operation  Do not cover the sensor by affixing a sticker With the lever in the “AUTO” (rain sensor) mode in ON and the lever in the “AUTO”...
Page 141 Wiper and washer switch CAUTION Misting function  If the washer is used in cold weather, the Move the lever in the direction of the arrow washer fluid sprayed against the glass may and release, to operate the wipers once. freeze resulting in poor visibility.
Page 142: Rear Window Demister Switch
Rear window demister switch*  Avoid using the washer continuously for NOTE Type 1 more than 20 seconds. Do not operate the  To avoid unnecessary discharge of the bat- washer when the fluid reservoir is empty. tery, do not use the rear window demister Otherwise, the motor may burn out.
Page 143: Horn Switch
Horn switch The rear window demister does not oper- Type 1 ate automatically. The heated mirrors will not operate auto- matically as well.  Setting change method: Hold down the rear window demister switch for about 10 seconds or more. •...
Page 144 Starting and driving Economical driving ................6-2 Brake assist system*...............6-68 Driving, alcohol and drugs ..............6-3 Emergency stop signal system*............6-69 Safe driving techniques ..............6-3 Anti-lock brake system (ABS) ............6-69 Power steering system ..............6-72 Running-in recommendations ............6-4 Parking brake ...................6-5 Active Stability & Traction Control (ASTC)* .......6-72 Parking .....................6-6 Cruise control* ................6-76 Steering wheel height and reach adjustment ........6-7...
Page 145: Economical Driving
Economical driving The drive mode-selector should be set to Economical driving Tyre inflation pressure “2H” when driving 4WD vehicles on normal roads and express ways to obtain best possi- E00600102770 Check the tyre inflation pressures at regular For economical driving, there are some tech- ble fuel economy.
Page 146: Driving, Alcohol And Drugs
Driving, alcohol and drugs Cooler or air conditioning Safe driving techniques E00600300446 The use of the air conditioning will increase Driving safety and protection against injury the fuel consumption. cannot be fully ensured. However, we recom- mend that you pay extra attention to the fol- lowing: Driving, alcohol and drugs E00600200070...
Page 147: Running-In Recommendations
Running-in recommendations not only because rearward vision will be Vehicles with M/T  Vehicles with Easy Select 4WD obstructed, but also the luggage may be pro- jected into the passenger compartment under Speed limit hard braking. Shift point 4D56 2H, 4H Running-in recommenda- 1st gear 20 km/h...
Page 148: Parking Brake
Parking brake Vehicles with A/T Vehicles with Super Select 4WD II To apply Speed limit 2WD models Shift point 2H, 4H, 4LLc 4HLc Shift point Speed limit 1st gear 15 km/h 5 km/h 1st gear 15 km/h 2nd gear 35 km/h 10 km/h 2nd gear 35 km/h...
Page 149: Parking
Parking NOTE CAUTION NOTE  Apply sufficient force to the parking brake  Before driving, be sure that the parking  To prevent the parking brake from being lever to hold the vehicle stationary after the brake is fully released and brake warning released unintentionally, the lever must be foot brake is released.
Page 150: Steering Wheel Height And Reach Adjustment
Steering wheel height and reach adjustment On vehicles equipped with A/T, apply the Always try to park your vehicle in a well lit Parking with the engine run- parking brake and place the selector lever into area. ning the “P” (PARK) position. If necessary, apply chocks to wheels.
Page 151: Inside Rear-View Mirror
Inside rear-view mirror Inside rear-view mirror To adjust the vertical mirror Type 1 position E00600802155 Adjust the rear-view mirror only after making any seat adjustments so you have a clear view It is possible to move the mirror up and down to the rear of the vehicle.
Page 152: Outside Rear-View Mirrors
Outside rear-view mirrors When the ignition switch is turned to the “ON” position or the operation mode is put in ON, the reflection factor of the mirror is auto- matically changed. NOTE  Do not hang items on, or spray glass cleaner on the sensor (1), as reduced sensitivity could result.
Page 153 Outside rear-view mirrors Manual outside rear-view mirrors CAUTION  Do not drive the vehicle with the mirror retracted in. Adjust the mirror surface by hands as indi- The lack of rearward visibility normally pro- cated by the arrows. vided by the mirror could lead to an accident. Except for vehicles equipped with the mirror retractor switch Push the mirror towards the back of the vehi-...
Page 154 Outside rear-view mirrors For vehicles equipped with the mirror CAUTION Retracting and extending the mir- retractor switch rors without using the mirror  It is possible to retract and extend the mirrors by hand. After retracting a mirror using the retractor switch mirror retractor switch, however, you should Retracting and extending the mir-...
Page 155 Outside rear-view mirrors NOTE NOTE Type 1 • Automatically extend when the driver’s • Deactivate the automatic extension func- door is closed, and then the following oper- tion. ation is performed. The outside rear-view mirrors can be [Except for vehicles equipped with the key- retracted or extended by the following less operation system] operations, even if changing to the any of...
Page 156: Ignition Switch
Ignition switch* Ignition switch START E00601403302 The starter motor operates. After the engine has started, release the key and it will auto- matically return to the “ON” position. NOTE  If your vehicle is equipped with an electronic immobilizer. To start the engine, the ID code which the transponder inside the key sends must match CAUTION the one registered in the immobilizer com-...
Page 157: Engine Switch
Immediately contact your authorised MITSUBISHI MOTORS dealer.  If the engine switch operation is not smooth and feels like it is sticking, do not operate the switch.
Page 158 Engine switch* NOTE CAUTION NOTE  Your vehicle is equipped with an electronic  When the engine is not running, put the oper- 1. Move the selector lever to the “P” immobilizer. ation mode in OFF. Leaving the operation (PARK) position, and then change the To start the engine, the ID code which the mode in ON or ACC for a long time when operation mode to OFF.
Page 159: Steering Wheel Lock
OFF, the operation mode ON details, consult authorised reminder inner buzzer sounds intermittently MITSUBISHI MOTORS dealer. to remind you to put the operation mode in OFF. Operation mode OFF reminder system Warning display (color liquid crystal display)
Page 160 Steering wheel lock NOTE CAUTION NOTE  When the following operation is performed  If the engine is stopped while driving, do not  When the steering wheel lock is abnormal, with the operation mode in OFF and the open a door or press the LOCK switch on the the warning lamp illuminates or warning dis- selector lever is in the “P”...
Page 161: Starting And Stopping The Engine
 Release the ignition key as soon as the Tips for starting safe place and contact your nearest author- engine starts to avoid damaging the starter ised MITSUBISHI MOTORS dealer. motor.  If your vehicle is equipped with a turbo- Except for vehicles equipped with the...
Page 162 Starting and stopping the engine 4. On vehicles equipped with M/T, depress WARNING NOTE the clutch pedal all the way and place the  Never run the engine in a closed or poorly  When the engine has not been started within gearshift lever in the “N”...
Page 163 Starting and stopping the engine NOTE NOTE NOTE  When the engine is not started, it may  If the engine is cold, the diesel preheat indi-  When starting the engine, the selector lever become hard to depress the brake pedal and cator lamp is on for a longer time.
Page 164 Starting and stopping the engine 2. Fully engage the parking brake while Remove the keyless operation key from the For vehicles equipped with the keyless depressing the brake pedal. key slot after starting the engine or changing operation system 3. On vehicles with M/T, press the engine the operation mode.
Page 165: Turbocharger Operation
Turbocharger operation* ation key in the key slot, the warning lamp NOTE will blink or warning display will appear for  Remove the object or additional key from the approximately 1 minute, the outer buzzer keyless operation key before inserting the sounds for approximately 3 seconds and the key into the key slot.
Page 166 Auto Stop & Go (AS&G) system* Indicator display CAUTION  If the vehicle will be stopped for a long time or if you will leave the vehicle unattended, stop the engine. [For vehicles with M/T] NOTE 1. Stop the vehicle. ...
Page 167 Auto Stop & Go (AS&G) system* NOTE CAUTION NOTE • The brake booster becomes inoperative and • On vehicles with M/T, do not move the • Ambient temperature is low the pedal effort will increase. gearshift lever to a position other than the •...
Page 168 Auto Stop & Go (AS&G) system* NOTE NOTE NOTE • The Hill Descent Control is operating (if so  If the air conditioning is operating, set the  If the engine does not restart automatically equipped) temperature control higher to lengthen the or if the engine stalls, the charge warning time that the engine is stopped automatically.
Page 169 Auto Stop & Go (AS&G) system* NOTE CAUTION NOTE  The vehicles with A/T have the function of • When the air conditioning is operated in  In the following cases, the engine will not preventing the unexpected start of the vehi- AUTO mode where the temperature control restart automatically.
Page 170: Manual Transmission
We recommend you to consult an authorised mission because the tractive force is very MITSUBISHI MOTORS dealer. great. Manual transmission* NOTE E00602002643  During cold weather, shifting may be diffi-...
Page 171 Manual transmission* Moving the gearshift lever to CAUTION 4N15 the “R” (Reverse) position  Do not depress the gearshift lever when moving it to any position other than the “R” E00615401396  2WD models (Reverse) position. If you always depress the gearshift lever when moving it, you could Vehicles with 5 M/T unintentionally move the gearshift lever to...
Page 172: Automatic Transmission Sports Mode 6A/T
Automatic transmission Sports Mode 6A/T* While depressing the brake pedal,  Vehicles with Super Select 4WD II Selector lever operation move the selector lever through the E00603302379 gate. Speed limit The transmission has 6 forward gears and Move the selector lever through the Shift point 1 reverse gear.
Page 173 Immediately have your vehicle checked by an authorised Selector lever position display Selector lever positions MITSUBISHI MOTORS dealer. If you need to move the vehicle, shift the E00603502153 E00603801973 When the ignition switch is turned to the selector lever as follows.
Page 174 Automatic transmission Sports Mode 6A/T* “N” NEUTRAL CAUTION NOTE  To prevent transmission damage, never shift  If your vehicle is equipped with the shift into the “D” (DRIVE) position from the “R” paddles, you can shift into sports mode with At this position the transmission is disen- (REVERSE) position while the vehicle is in shift paddles when the selector lever is in the...
Page 175 Automatic transmission Sports Mode 6A/T* NOTE + (SHIFT UP) Vehicles equipped with the mono-color liquid crystal display  To maintain good running performance, the The transmission shifts up by one gear with transmission may refuse to perform an each operation. upshift when the selector lever or the shift paddles are operated to the “+ (SHIFT UP)”...
Page 176 A/T. Have the vehicle inspected by an E00660900059 CAUTION authorised MITSUBISHI MOTORS dealer When the selector lever position display  If the lamp comes on, reduce the engine immediately. blinks while you are driving, there could be a speed and stop the vehicle in a safe area.
Page 177 Automatic transmission Sports Mode 6A/T* CAUTION CAUTION • Stop your vehicle in a safe place, put the  Depress the brake pedal with the right foot at selector lever in the “P” (PARK) position, all times. and open the bonnet with the engine run- Using the left foot could cause driver move- NOTE ning to allow the engine to cool down.
Page 178: Easy Select 4Wd
Easy Select 4WD* checked at an authorised MITSUBISHI Passing acceleration Parking MOTORS dealer immediately. E00604501401 E00604701360 To gain extra acceleration in “D” (DRIVE) To park the vehicle, first bring it to a com- Easy Select 4WD position, push the accelerator to the floor. The plete stop, fully engage the parking brake, A/T will automatically downshift.
Page 179 Easy Select 4WD* Drive mode-selector position, drive mode indicator display, 2WD/4WD operation indicator lamp/dis- play and low-range indicator lamp E00641100111 Indicator lamp/display Drive mode-selector position Driving conditions Mono-color liquid Color liquid crystal crystal display display Rear-wheel drive When driving on dry paved road. 4-wheel drive When driving on rough, sand or snow covered roads.
Page 180 Easy Select 4WD* CAUTION  The “4L” range gives maximum torque for low-speed driving on steep slopes, as well as sandy, muddy, and other difficult surfaces. On vehicles with A/T, do not exceed speeds of approximately 70 km/h in “4L” range. ...
Page 181 Easy Select 4WD* Procedure To shift from Vehicles with M/T Vehicles with A/T The drive mode-selector can be operated while the vehicle The drive mode-selector can be operated while the vehicle is either moving or stationary. is either moving or stationary. When the vehicle is not in motion, shift the selector lever When the vehicle is not in motion, shift the gearshift lever to the “N”...
Page 182 Easy Select 4WD* CAUTION  Do not operate the drive mode-selector while the rear wheels of the vehicle are slipping on snow or ice. When the ignition switch is in the “ON” posi- Indicator lamp/display : Blink tion or the operation mode is put in ON, the : Illuminate E00693900020 2WD/4WD operation indicator lamp (1) and...
Page 183 Restart the engine. The lamp should resume and make the range selection again. normal operation. If the lamp continue to blink, have the vehicle checked by an author- ised MITSUBISHI MOTORS dealer as soon as possible. : Blink 6-40 Starting and driving...
Page 184 Easy Select 4WD*  “2H”  “4H”  “4H”  “4L” Drive mode indicator display and 2WD/4WD operation indicator display Drive mode-selec- Drive mode- Indicator display tor position selector Indicator display E00694100087 position Drive mode switch- ing in progress Drive mode switching in progress A: Drive mode indicator display...
Page 185: Super Select 4Wd Ii
Super Select 4WD II* NOTE NOTE NOTE  If, after a “4H”  “4L” selection has been  When the drive mode-selector is set between  The active stability control function is sus- “2H”  “4H”, the front wheel indicator dis- made, front and the rear wheel displays con- pended while “4L”...
Page 186 Super Select 4WD II* appropriate position according to the road Drive mode Drive mode-selector position, surface conditions. The Drive mode indicator indicator drive mode indicator display display and the 2WD/4WD operation indica- Drive mode- display and Driving and 2WD/4WD operation indi- tor display indicate the drive mode-selector selector posi- 2WD/4WD...
Page 187 Super Select 4WD II* The drive mode-selector should be positioned CAUTION Drive mode-selector operation in accordance with the following operating  The “4LLc” range gives maximum torque E00605901620 conditions: for low-speed driving on steep slopes, as The drive mode is shown on the drive mode- well as sandy, muddy, and other difficult sur- selector knob.
Page 188 Super Select 4WD II* Procedure To shift from Vehicles with M/T Vehicles with A/T 4HLc 4LLc Stop the vehicle, depress the clutch pedal to the floor and Stop the vehicle, shift the selector lever to the “N” (NEU- operate the drive mode-selector. TRAL) position, and operate the drive mode-selector.
Page 189 Super Select 4WD II* “2H”  “4H” “4H”  “4HLc” Drive mode indicator display and 2WD/4WD operation indi- cator display Drive mode-selec- Drive mode-selec- Indicator display Indicator display tor position tor position E00606001660 Drive mode switch- Drive mode switch- ing in progress ing in progress A: Drive mode indicator display B: Front wheel indicator display...
Page 190 Super Select 4WD II* “4HLc”  “4LLc” NOTE NOTE  When the drive mode-selector is set between  When parking, apply the parking brake “2H”, “4H” and “4HLc”, the front wheel before stopping the engine and make sure Drive mode- and/or centre differential lock displays blink that the front and the rear wheel displays are selector...
Page 191 Super Select 4WD II* NOTE CAUTION  If the selector lever is shifted from the “N”  If the warning display is displayed on the (NEUTRAL) position to the other position or information screen in the multi information release the brake pedal during shifting pro- display, a problem has occurred with the cess between “4HLc ...
Page 192: Off Road Mode
Off Road mode* Off Road mode E00642500109 The Off Road mode is the function that enhances driving smoothly on the off-road by selecting the most suitable engine, transmission, and brake control according to the road surface conditions when the drive mode position is in “4H” or “4L” (Easy Select 4WD), “4HLc” or “4LLc” (Super Select 4WD II).
Page 193 Off Road mode* Off Road mode-selector opera- NOTE Off Road mode indicator dis- tion play  When the rear differential lock switch is turned on while the Off Road mode is acti- E00642700215 E00642800144 vated, the Off Road mode is returned to 1.
Page 194 Rear differential lock* NOTE Type 2 Type 1 • Rear Differential Lock (if so equipped): activating • ASTC warning lamp: illuminating or blink- refer to “ASTC warning lamp/display” on page 6-75 Rear differential lock E00606201372 If one wheel starts to spin freely and the vehi- Type 2 Operating the rear differential cle becomes stuck and cannot be freed even...
Page 195 Rear differential lock* [Vehicles equipped with the color liquid crys- NOTE The rear differential lock indi- tal display] cator lamp/display  The rear differential lock does not operate when the drive mode-selector is in “2H”posi- E00606301807 Indicator lamp tion (Easy Select 4WD), “2H” or “4H” posi- When the ignition switch is turned to the tion (Super Select 4WD II).
Page 196: Rear Differential Lock
Rear differential lock* [Vehicles equipped with the mono-color [Vehicles equipped with the color liquid : Remain off liquid crystal display] crystal display] The opera- Rear differential lock NOTE The opera- tion state of Rear differential lock indicator lamp/display tion state of ...
Page 197 The indicator using it. reactivated, have the vehicle checked by an lamp/display will illuminate steadily and authorised MITSUBISHI MOTORS dealer the rear differential lock will be activated. as soon as possible. When one of the wheels has fallen...
Page 198 Rear differential lock* When driving on rocky roads When the vehicle is unable to move because one of the wheels is suspended in the air. WARNING Examples of incorrect use of the  If the rear differential lock is used by mis- rear differential lock take when turning a curve or making a right or left turn at a crossing or the like:...
Page 199: 4-Wheel Drive Operation
4-wheel drive operation* WARNING  If the rear differential lock is used by mis- take except when making an emergency escape on snow or frozen road: It becomes difficult to make a steady turn.  In the case where the condition of the road is different for the right tyre to drive from the left tyre (such as one tyre on a paved road and the other on ice), direction of the...
Page 200 4-wheel drive operation* NOTE  The driving posture should be more upright and closer to the wheel than usual; adjust the seat to a good position for easy steering and pedal operation. Be sure to wear the seat belt.  After driving on rough roads, check each part of the vehicle and wash it thoroughly with water. Refer to the “Vehicle care” section and “Inspection and maintenance following rough road operation”...
Page 201 4-wheel drive operation* Driving on dry paved road and CAUTION NOTE highway  Selecting “4H” or “4L” position (Easy Select  The use of snow tyres and/or tyre chains is 4WD), “4HLc” or “4LLc” position (Super recommended. E00646400050 Select 4WD II) to drive on dry paved road ...
Page 202 4-wheel drive operation* Road mode-selector (if so equipped) to CAUTION NOTE “GRAVEL” may help you drive smoothly.  If any of following conditions occur while  If it is necessary to drive in extremely muddy the vehicle is being driven, immediately park conditions, the use of tyre chains is recom- Driving on deep snow or muddy your vehicle in a safe place and follow these...
Page 203 4-wheel drive operation* depress the accelerator pedal to start the vehi- “4LLc” position (Super Select 4WD II) and Set the drive mode-selector to “4H” or “4L” cle and drive at a possible constant low speed. drive at a low speed. Depending on the road position (Easy Select 4WD), “4HLc”...
Page 204 NOTE WARNING low speed, a slight difference in steering may  MITSUBISHI MOTORS is not responsible  Go straight up. Do not try to traverse be experienced similar to as if the brakes to the operator for any damage or injury across a steep slope.
Page 205: Inspection And Maintenance Following Rough Road Operation
4 wheels, the performance of the vehicle affect the life span of the vehicle; consult an MITSUBISHI MOTORS dealer as soon when operating in 4-wheel drive is greatly authorised MITSUBISHI MOTORS dealer as possible to have the brakes checked.
Page 206 10-13.  Check the tyre inflation pressure regu- Only when you cannot receive a towing ser- larly. vice from a MITSUBISHI MOTORS dealer or commercial tow truck service, tow your vehicle carefully in accordance with the CAUTION instructions given in “Towing” on page 8-19.
Page 207: Limited-Slip Differential
Have the vehicle serviced by an will not work effectively. when the vehicle is cornering. The difference authorised MITSUBISHI MOTORS dealer at  If the power assist is lost or if either brake between the limited-slip differential and a...
Page 208: Hill Start Assist
MITSUBISHI MOTORS dealer. Doing so could cause an accident.  Do not turn the ignition switch to the When driving downhill WARNING “LOCK”...
Page 209: Hill Descent Control (Hdc)
Hill Descent Control (HDC)* Warning lamp To operate NOTE • On vehicles equipped with M/T, the gear- E00628101371 1. Stop the vehicle completely using the shift lever is in the following position. Warning display brake pedal. [When starting an uphill slope forwards.] The gearshift lever is in any position other 2.
Page 210 When ASTC warning lamp set to ON (stand by). WARNING come on, have the vehicle inspected at an authorised MITSUBISHI MOTORS dealer.  The driver has the responsibility to drive Indicator lamp (Refer to “ASTC warning lamp/display” on safely.
Page 211: Brake Assist System
Brake assist system* NOTE NOTE NOTE • Brake system: brake temperature high • On vehicles with M/T, the gearshift lever is • Rear differential lock (if so equipped): acti- placed in the forward gear except the 1st vating • ASTC warning lamp: illuminating or blink- position.
Page 212: Emergency Stop Signal System
Emergency stop signal system* NOTE CAUTION Anti-lock brake system (ABS)  Once the brake assist system is operational,  If the ABS warning or ASTC warning is dis- it maintains great braking force even if the played, the emergency stop signal system E00607102838 brake pedal is lightly released.
Page 213 Anti-lock brake system (ABS)  When the ABS is in use, you may feel the ABS warning lamp/display CAUTION brake pedal pulsation and the vibrations • When the ignition switch is turned to the E00607202712 of the vehicle body and steering wheel. It Warning lamp “ON”...
Page 214 Stop the vehicle in a safe place and contact an around the wheels. On vehicles that have an authorised MITSUBISHI MOTORS dealer. ABS, be careful not to damage the wheel Starting and driving...
Page 215: Power Steering System
Power steering system Power steering system Active Stability & Traction CAUTION Control (ASTC)  Do not install any aftermarket limited slip E00607401472 differential (LSD) on your vehicle. The The power steering system operates while the E00616701947 active stability control function may stop engine is running.
Page 216 Active Stability & Traction Control (ASTC)* NOTE NOTE “ASC OFF” switch; the indicator is turned off.  On vehicles with the rear differential lock,  The active stability control function does not the ASTC and ABS functions are suspended operate when the drive mode-selector is in while the rear differential lock is activated.
Page 217  Even if the active stability control function is ON, please contact your nearest authorised turned off, it may activate depending on the vehicle’s movement. MITSUBISHI MOTORS dealer for inspec- tion. Active Traction Control func- ASTC indicator lamp The indicator lamp will blink when tion the ASTC is operating.
Page 218 Active Stability & Traction Control (ASTC)* CAUTION NOTE NOTE  If the temperature in the braking system con-  The ASTC function indicator display illumi-  The indicator lamp may turn on when tinues to increase due to continuous brake nates only when the 2WD/4WD operation you start the engine.
Page 219: Cruise Control
Cruise control* CAUTION CAUTION Cruise control switches  The system may be malfunctioning.  When you do not wish to drive at a set speed, Park your vehicle in a safe place and stop the turn off the cruise control for safety. engine.
Page 220 Cruise control* Indicator display NOTE To increase the set speed  When operating the cruise control switches, E00609401997 press the cruise control switches correctly. There are 2 ways to increase the set speed. The set speed driving may be deactivated automatically if two or more switches of the 2.
Page 221 Cruise control* When you reach your desired speed, release Accelerator pedal the switch. Your new cruising speed is now set. While driving at the set speed, use the accel- erator pedal to reach your desired speed and then push down the “SET -” switch (B) and release the switch momentarily to set a new desired cruising speed.
Page 222 15 km/h or more below the set speed your vehicle inspected by an authorised because of a hill, etc. MITSUBISHI MOTORS dealer.  When your speed slows to approximately 40 km/h or less. Starting and driving...
Page 223: Forward Collision Mitigation System (Fcm)
Forward Collision Mitigation system (FCM)*  Indicator lamp go off. also turns ON/OFF at the same time. (Vehi- To resume the set speed cles equipped with the UMS) E00609802158 Forward Collision Mitiga- If the set speed driving is deactivated by the tion system (FCM) condition described in “To deactivate”...
Page 224 Forward Collision Mitigation system (FCM)* WARNING Forward collision warning CAUTION function  A driver is responsible for driving safely.  Under certain conditions, the audible alarm The FCM is the system to mitigate colli- may not work at all or may be scarcely audi- E00635401217 sion-caused damages or to avoid collisions ble.
Page 225 Forward Collision Mitigation system (FCM)* pedestrian in front, this function deploys the While the FCM braking control is triggered, CAUTION brake assist sooner the brake assist operation. you are warned of the hazard with a  When applying the brake during the auto- The FCM brake assist function operates when “BRAKE!”...
Page 226 • When replacing the windscreen wipers similar shaped vehicle. • When pedestrians gather in a group. without using the MITSUBISHI MOTORS • When there is a different object near the GENUINE parts. • When a pedestrian clothing appears to be vehicle.
Page 227 Forward Collision Mitigation system (FCM)* CAUTION CAUTION CAUTION • When the pedestrian is walking fast or run- • When quickly approaching a vehicle in • When passing through an area that objects ning. front to overtake it. may contact the vehicle, such as thick grass, tree branches, or a banner.
Page 228 Forward Collision Mitigation system (FCM)* CAUTION FCM and UMS ON/OFF switch To turn on/off the system • When the tyre pressure is not proper. E00635601453 You can switch the system from OFF to ON This switch is used to turn on and off the •...
Page 229 Forward Collision Mitigation system (FCM)* When “NEAR” is selected NOTE To change alarm timing  The indicator is combined with the Give a short press to the FCM and UMS “UMS OFF” indicator. ON/OFF switch to change the timing at which the frontal collision alarm is triggered.
Page 230 Contact authorised to operation. may appear. MITSUBISHI MOTORS dealer for inspec- If the display keeps showing the message, indicator will appear on the informa- tion of the sensor. there is a possibility that the FCM has a mal- tion screen of the multi information display function.
Page 231 • Do not apply an impact or load on the sen- please contact an authorised MITSUBISHI MITSUBISHI MOTORS dealer. sor or its surrounding area. MOTORS dealer. • Do not put anything including a sticker or film to the outer side of the windscreen in front of or surrounding area of the sensor.
Page 232 MITSUBISHI MOTORS dealer. If you need to replace the windscreen, con- tact an authorised MITSUBISHI MOTORS dealer.  The sensor emits infrared rays when the operation mode is in ON. Do not look into the sensor by using optical goods such as a magnifying glass.
Page 233: Ultrasonic Misacceleration Mitigation System (Ums)
Ultrasonic misacceleration Mitigation System (UMS)* Ultrasonic misacceleration Mitigation System (UMS) E00643400411 The Ultrasonic misacceleration Mitigation System (UMS) operates to prevent sudden starts and mitigate collision-caused damages by suppress- ing the engine output for up to approximately 5 seconds when the system judges that the system is detected the vehicle or obstacles within approximately 4 m in front and behind your vehicle and judges that accelerator pedal was depressed promptly and too strongly such as misopera- tion of it.
Page 234 Ultrasonic misacceleration Mitigation System (UMS)* Situation Operation display Buzzer When an obstacle is detected in front of your vehicle with the Intermittent selector lever in the “D” (DRIVE) position or in the sport beeping sound mode, if the accelerator pedal is depressed promptly and too strongly, the engine output is suppressed for up to approxi- mately 5 seconds.
Page 235 Ultrasonic misacceleration Mitigation System (UMS)* WARNING CAUTION CAUTION • Turn the system OFF. (Continuously • The sensors or surroundings have been • For a short period after the system judges press the FCM and UMS ON/OFF switch wiped by hand. the repeated depression of the accelerator for more than 3 seconds.) pedal at a few seconds interval as a release...
Page 236 Ultrasonic misacceleration Mitigation System (UMS)* CAUTION CAUTION Obstacle detection areas • When running the road, the gradient • Do not modify the suspension of your vehi- E00643500021 changes suddenly. cle. The detection areas of the front and rear sen- • When passing through the mass of the •...
Page 237 UMS ON/OFF is switched in MITSUBISHI MOTORS dealer. • Obstacles that have irregular surface. conjunction with the ON/OFF state of the • Obstacles that have the shape of the pole FCM.
Page 238: Blind Spot Warning (Bsw) (With Lane Change Assist)
Blind Spot Warning (BSW) some malfunctions in the system or the sen- sor. Have the vehicle inspected at an author- (with Lane Change Assist) ised MITSUBISHI MOTORS dealer as soon E00644300143 as possible. WARNING The Blind Spot Warning (BSW) is a driving...
Page 239 Blind Spot Warning (BSW) (with Lane Change Assist)* Detection areas WARNING • When the heights of the next lane and E00644400362 The BSW uses two sensors (A) located inside your lane are different. the rear bumper. • Immediately after the BSW has been turned on.
Page 240 Blind Spot Warning (BSW) (with Lane Change Assist)* WARNING To operate NOTE • When the sensor is extremely hot or cold  When the ignition switch is turned to the E00652300272 When the BSW switch is pressed while the (while the vehicle is parked for a long “LOCK”...
Page 241 Have the vehicle inspected at an author-  Set the BSW to OFF when towing. alert the driver. ised MITSUBISHI MOTORS dealer as soon  The Blind Spot Warning lamp in the outside as possible. rear-view mirror may not be visible due to...
Page 242: Rear Cross Traffic Alert (Rcta)
MITSUBISHI MOTORS dealer. the bumper surface around the sensor. When the warning display does not disappear after having cleaned the sensor, contact an authorised MITSUBISHI MOTORS dealer. Rear Cross Traffic Alert (RCTA) E00652400231 The Rear Cross Traffic Alert (RCTA) is an aid system for backing up.
Page 243 • When the reversing speed of your vehicle is RCTA may not function properly. Have the approximately 18 km/h or higher. vehicle inspected authorised MITSUBISHI MOTORS dealer. 6-100 Starting and driving...
Page 244: Reversing Sensor System
Reversing sensor system* to detect low or thin objects or objects near To operate Reversing sensor system the rear bumper. Thus, make sure to check the surroundings as you operate the vehicle in a E00615501528 1. Press the BSW switch while the operation safe manner.
Page 245 • The stickers or accessories have been and prevent the system from functioning attached to the sensors or surroundings. properly. Have the vehicle inspected at an • The sensors or surroundings are covered authorised MITSUBISHI MOTORS dealer. with ice, snow, or mud. 6-102 Starting and driving...
Page 246 Reversing sensor system* Back sensor (vehicles without a towbar) NOTE Warning for obstacles Vehicle to obstacle Warning dis-  The buzzer may sound lower than the normal distance play/sound cycle warning sound when the reversing sensor If there is an obstacle behind the vehicle, a system is receiving ultrasonic noise from Approximately 125 warning will be issued with the information...
Page 247 Example: Rear corner sensor (left) malfunctioning details, consult authorised  After pressing the “SONAR” switch, revers- MITSUBISHI MOTORS dealer. ing sensor system operation differs accord- ing to the detection area setting. • Setting when towbar is not equipped Changing the detection areas When the gearshift lever or the selector lever is moved to the “R”...
Page 248: Sensor System
Sensor system* CAUTION  Make sure to check the surroundings with your own eyes to ensure safety. Do not oper- ate the vehicle by relying on the sensor sys- tem alone. Obstacle detection areas E00647800367 The detection areas of the corner and back sensors are limited to those shown in the illustration.
Page 249 Sensor system* NOTE CAUTION  The sensors do not detect objects located in • The vehicle tilts significantly. the area directly below or near the bumper. If • The vehicle is driven on a rough road (with the height of an object is lower than the a bumpy, gravel, hilly, or grassy surface).
Page 250 Sensor system* Vehicle to obstacle Warning dis- To operate distance play/sound cycle E00648100224 Approximately 80 to To operate the system, the ignition switch is Fast intermittent 40 cm in the “ON” position or the operation mode is put in ON. When the sensor system is oper- Within approxi- Continuous ated, the sensor system operation indicator...
Page 251  After pressing the “SONAR” switch, sensor details, consult authorised system operation differs according to the MITSUBISHI MOTORS dealer. detection area setting. • Setting when towbar is not equipped When the selector lever is moved to the “R” Changing the detection areas...
Page 252: Rear-View Camera
Rear-view camera* Range of view of rear-view Range of view of rear-view camera camera The range of view of the rear-view camera is limited to the area shown in the illustrations. It cannot show the both sides and the lower part of the rear bumper, etc.
Page 253 Rear-view camera* operation mode in ON, the view behind the NOTE Reference lines on the screen vehicle will automatically appear on the  If the atmospheric temperature is extremely screen of the Mitsubishi Multi Entertainment hot or extremely cold, the rear-view camera Reference lines and upper surface of the rear System (MMES) or the DVD AUDIO.
Page 254 Rear-view camera* CAUTION  Due to the number of people in the vehicle, the fuel quantity, the weight and positioning of luggage, and/or the condition of the road surface, the lines in the view from the rear- view camera may not be accurately posi- tioned relative to the actual road.
Page 255: Multi Around Monitor
Multi Around Monitor* not use them as a guide to distances to solid objects. Example: On the screen the point B appears the nearest, then the point C and A in order of distance. The point A and B actually are the same distances from the vehicle, and the point C is farther off than the point A and B.
Page 256 Multi Around Monitor* B- Front-view camera CAUTION Location of each cameras C- Side-view camera  The Multi Around Monitor is an assistance The cameras are integrated into the location system that enables the driver to check the WARNING as shown below. safety around the vehicle.
Page 257 Multi Around Monitor* Range of view of the Multi Around Monitor cameras A: Front-view camera B: Side-view camera (Right) C: Side-view camera (Left) D: Rear-view camera 6-114 Starting and driving...
Page 258 Multi Around Monitor* Types of views of the Multi Side-view/Front-view mode Around Monitor Views of the passenger’s side of the vehicle and the front of the vehicle are displayed. Two different types of views are displayed on the left side and the right side respectively. Bird’s eye-view/Rear-view mode Views of the surroundings of the vehicle and behind the vehicle are displayed.
Page 259 Multi Around Monitor* NOTE NOTE NOTE • When the light of the sun or the light from a • Do not splash the camera with boiling  The passenger’s side screen can be switched vehicle’s headlamps shines directly into the water.
Page 260  When you place the gearshift lever or the played correctly. Be sure to have it inspected selector lever in the “R” (REVERSE) posi- by an authorised MITSUBISHI MOTORS tion with the front view displayed on the dealer. driver’s side screen, the driver’s side screen 1- Approximately 100 cm from the front switches to the Rear-view mode.
Page 261 Multi Around Monitor* 2- Approximately 200 cm from the rear Rear-view mode Errors between the display and edge of the rear bumper the actual road surface E00645600244 Reference lines for the distance and the vehi- E00645900029 CAUTION cle width and upper surface of the rear The reference lines for distance and vehicle ...
Page 262 Multi Around Monitor* Therefore when there is an obstacle on the B: Objects shown on the screen downward slope, it appears closer than its actual position.  When there is an upward slope behind the vehicle E00648700057 The reference lines are displayed closer than the actual distance.
Page 263 Multi Around Monitor* not use them as a guide to distances to solid CAUTION objects.  The bird’s-eye view is an simulated view Example: On the screen the point B appears processed by combining view captured by the nearest, then the point C and A in order of “Front-view camera”, “Side-view cameras distance.
Page 264: Cargo Loads
Cargo loads 1. Stop the vehicle in a safe place. NOTE NOTE  In the bird’s eye-view mode, since the views CAUTION  When the selection mode is in the following captured by the four cameras, “Front-view situations, the vehicle icon colour does not ...
Page 265 Cargo loads CAUTION • Do not place cargo or luggage on the instru- ment panel. Also, do not stack up cargo or luggage on the front passenger’s seat or the rear seat. Having the driver’s vision blocked, and your cargo being thrown inside the cabin if you suddenly have to brake can cause a serious accident or injury.
Page 266 For pleasant driving Ventilators ..................7-2 Listen to MP3s ................7-51 Cooler* .....................7-4 Listen to an iPod*................7-53 Automatic climate control air conditioning*........7-7 Listen to Audio Files on a USB Device* ........7-55 Display Indicator ................7-57 Rear circulator* ................7-14 Important air conditioning operation tips ........7-16 Audio Quality and Volume Balance Adjustment ......7-59 Air purifier ..................7-16 System Settings ................7-59...
Page 267: Ventilators
Ventilators To close the vent, move the knob (A) to the To close the vent, move the knob (A) to the Ventilators inside as far as possible. outside as far as possible. E00700102061 Type 1 Left Right 1- Centre ventilators 1- Close 2- Side ventilators 2- Open...
Page 268 Ventilators Mode selection E00700302845 To change the position and amount of air flowing from the ventilators, turn the mode selection dial. (Refer to “Mode selection dial” on page 7-5.) On vehicles with the automatic climate control air conditioning, press the MODE switch or demister switch. (Refer to “MODE switch” on page 7-12, “Demister switch”...
Page 269: Cooler
Cooler* NOTE Control panel  For vehicles with the Auto Stop & Go E00731201087 (AS&G) system, the windows may start to fog up during the Auto Stop & Go (AS&G) system is operating. If this occurs, press the demister switch to remove fog from the win- dows.
Page 270 Cooler*  “ ” Outside air Mode selection dial NOTE Outside air is introduced into the passen- E00731501048  Normally, use the “ ” (outside) position ger compartment. To change the position of air flowing from the to keep the windscreen and side windows ...
Page 271 Cooler* 2. Set the air selection lever to the “ ” (outside) position. 3. Change the temperature by turning the control dial clockwise or anticlockwise. 4. Select the desired blower speed. CAUTION  If the outside air is dusty or otherwise con- taminated, or if high cooling performance is desired, set air selection lever to the “...
Page 272: Automatic Climate Control Air Conditioning
Automatic climate control air conditioning* Automatic climate control air conditioning E00702402172 The air conditioning can only be used while the engine is running. CAUTION  The engine speed may increase when the air conditioning is operating. With an increased engine speed, an A/T vehicle will creep to a greater degree than with a lower engine speed.
Page 273 Automatic climate control air conditioning* 11- Air conditioning indicator 12- Mode selection display 13- Blower speed display Dual-zone automatic climate control air conditioning - Type 2 11- Passenger’s side temperature display 1- Passenger’s side temperature control  P.7-9 switch 12- DUAL indicator 2- Air conditioning switch 13- Mode selection display 3- Blower speed selection switch...
Page 274 Automatic climate control air conditioning* The selected temperature will be shown in the NOTE Blower speed selection switch display (A).  There is an interior air temperature sensor E00702801427 (A) in the illustrated position. Press of the blower speed selection Never place anything on top of the sensor, switch to increase the blower speed.
Page 275 Automatic climate control air conditioning* operating conditions can be changed as If the driver’s side temperature control NOTE desired. switch is pressed, the passenger’s side  While the engine coolant temperature is low, For further information, we recommend you temperature will also be controlled to the the temperature of the air from the heater to consult an authorised MITSUBISHI same setting temperature as the driver’s...
Page 276 Automatic climate control air conditioning* 2 sounds are emitted and the indicator NOTE lamp flashes 3 times.  When the engine coolant temperature rises to a certain level, the air selection is automati- NOTE cally switched to the recirculation position and the indicator lamp (A) comes on.
Page 277 Automatic climate control air conditioning* The air conditioning switch is not con- Air conditioning switch trolled automatically as long as the air E00703502763 conditioning switch is not operated. Press the switch to turn the air conditioning  Setting change method on, the “...
Page 278 Automatic climate control air conditioning* Demister switch Operating the system in auto- NOTE matic mode  If the blower speed selection switch, air con- E00703901092 ditioning switch, MODE switch, or air selec- When this switch is pressed, the mode E00704102838 tion switch is operated while the system is changes to the “...
Page 279: Rear Circulator
Rear circulator*  For ordinary demisting  For quick demisting NOTE  For vehicles with the Auto Stop & Go (AS&G) system, if the demister switch is Type 1 Type 1 pressed, the Auto Stop & Go (AS&G) sys- tem will not operate and the engine will not stop automatically even if the vehicle is stopped.
Page 280 Rear circulator* Air flow and direction adjust- NOTE ments  Do not put foreign objects into the air inlet port (B). Move the flap (A) to adjust the air flow direc- tion. To operate the rear circulator in the rear seat To operate the rear circulator E00779000028 in the front seat...
Page 281: Important Air Conditioning Operation Tips
Important air conditioning operation tips  Close the windows when the air condi- It is recommended that the refrigerant be tioning is in use. The entry of outside air recovered and recycled for further use. through open windows will reduce the cooling efficiency.
Page 282: Am/Fm Radio/Cd Player With Aux
AM/FM radio/CD player with AUX*  Furthermore, even if there is no specific AM/FM radio/CD player Important Points on Usage denotation of trademarks or registered with AUX E00735500023 trademarks, these are to be observed in their entirety. E00708503547 iPod/iPhone Playback Function The audio system can only be used when the ...
Page 283: Handling Of Discs
Handling of Discs Supported models  Do not forcefully insert a disc if another is (water droplets) to form on the disc and inter- already within the device. This can result nal optical components, and this may prevent  iPhone5S in damage to discs, or malfunction.
Page 284: Audio Files (Mp3/Wma/Aac)
Audio Files (MP3/WMA/AAC)  Depending on the disc, some functions • Some parts may not be played. Maxi- may not be used, or the disc may not be • Tracks may freeze during playback. Com- Type Size played. • Tracks may be displayed erroneously. playing ments ...
Page 285 Audio Files (MP3/WMA/AAC) Speci- CAUTION Name fica- Explanation ROOT  Do not append the file extensions “.mp3”, Folder tion “.wma”, “.m4a”, other than Audio file MP3/WMA/AAC format files. Playing discs Format ISO96 Level Maximum 8 with these types of files recorded upon them specifica- character file may cause the files to be incorrectly identi-...
Page 286 Audio Files (MP3/WMA/AAC) video compression standard used in video Speci- Item Details CDs, etc. Name fica- Explanation Sampling MPEG-1: 32/44.1/48 MP3 is one of the audio compression meth- tion frequency MPEG-2: 16/22.05/24 ods contained in the MPEG audio standard, Maxi- 509 files [kHz] and reduces the quality of sounds that are...
Page 287 Audio Files (MP3/WMA/AAC) format that has a higher compression ratio Item Details CAUTION than MP3. Bit rate [kbps] 32 to 192  AAC files different to the standards at right may not be played correctly, or file/folder Support NOTE names may not be displayed correctly. (variable bit rate) ...
Page 288: Important Points On Safety For The Customer
Important Points on Safety for the Customer Item Details WARNING WARNING Supported tag AAC tags or ID3 tags  The driver should not perform compli-  During thunderstorms, do not touch the information Title, Artist name, cated operations while driving. antenna or the front panel.
Page 289 Operation Keys Disc slot Disc *Label side Turn the power on, and resume playback Turn the SEL•PWR•VOL key clockwise Push the disc in a certain amount, and the from the previous status. to increase, and counter-clockwise to product will pull the disc in, and playback 2.
Page 290 Operation Keys Explanation of Buttons E00737501431 This explains names and functions of each part. 5- MEDIA key 8- SEL•PWR•VOL key Each time this is pressed, the audio Adjust the volume, and turn the power Use to eject a disc. source switches in the order “CD”, ON/OFF.
Page 291: Listen To Radio
Listen to Radio 12- 4RPT key Type 2 For audio, press to turn repeat playback mode on/off; for radio, use as preset key 4. 13- 5RDM key For audio, press to turn random play- back mode on/off; for radio, use as pre- set key 5.
Page 292: Listen To Cds
Listen to CDs Manual/Seek Station Selection NOTE NOTE  If a preset key that already has a station reg-  Each time the AUTO-P key is pressed, this istered is selected, then this is overwritten switches between normal reception and Press the key or the key to the fre-...
Page 293: Listen To Mp3S/Wmas/Aacs
Listen to MP3s/WMAs/AACs This enables selection of the next or previous Play the tracks on the disc in a random order. Insert a disc to automatically start playback.  “Insert/Eject Discs” (P.7-24) track. If a disc is already within the product, press NOTE the MEDIA key to switch to CD as the Fast Forward or Rewind...
Page 294: Listen To An Ipod
Listen to an iPod* Play the tracks in the folder in a random 4. Turn the SEL•PWR•VOL key to select Repeat Playback (RPT) order. the file. 5. Press the SEL•PWR•VOL key. Press the 4RPT key. NOTE This plays the selected file (track). Repeat playback of the track currently being ...
Page 295 Listen to an iPod* CAUTION NOTE Select the Track (File)  No indemnification for data loss resulting  Depending on the iPod/iPhone, the button when the iPod/iPhone is connected to the functions on the product may not operate Press the key or key to select the product will be possible.
Page 296: Listen To Audio Files On A Usb Device
Listen to Audio Files on a USB Device* 2. Turn the SEL•PWR•VOL key to select Shuffle Playback (RDM) Listen to Audio Files on a the category. USB Device 3. Press the SEL•PWR•VOL key. Categories Press the 5RDM key. or tracks within the selected category are E00736501522 displayed.
Page 297 Listen to Audio Files on a USB Device* This enables selection of the next or previous NOTE NOTE track.  Digital audio players that support the mass  Depending on the status of the vehicle and storage class specifications can be con- device, the iPod/iPhone may not be played Fast Forward or Rewind nected.
Page 298: Use Aux
Use AUX Repeat playback of the tracks within the NOTE Use AUX folder currently being played.  Even if the file is selected, all folder random E00736901249 playback will not be cancelled. By connecting external input cables and AUX NOTE devices to this product, you can play tracks ...
Page 299: Display Indicator
Display Indicator NOTE Change the Display Mode NOTE  Depending on the audio device to be con-  If there is no artist text information to dis- E00738501249 nected, noise may be emitted. play, then “Track No. + Playtime” is dis- You can change the content of the display played.
Page 300: Audio Quality And Volume Balance Adjustment
Audio Quality and Volume Balance Adjustment Turning the SEL•PWR•VOL key counter- 1. Hold down the /MENU key. During iPod Playback clockwise or clockwise, the adjustment 2. Turn the SEL•PWR•VOL key to select E00738901054 items switch as shown below. “CLOCK MODE” or “CLOCK ADJUST During other than Podcast playback, this BASSTREBLEFADERBAL- MODE”.
Page 301: Troubleshooting
Troubleshooting Troubleshooting E00738401310 Please check these items if a message appears on the display, or if you think something is not working properly. If This Message Appears... A message is displayed on this product according to the situation. Mode Message Cause Response DISC_ERROR...
Page 302 Troubleshooting Mode Message Cause Response Confirm audio files that can be played.  “Audio NO _ FILE There are no audio files that can be played. files (MP3/WMA/AAC)” (P.7-19) DEVICE _ ERR An unsupported USB device has been connected. Confirm the USB device. BUS_POWER There is high electrical current.
Page 303: Am/Fm Radio/Cd Player
AM/FM radio/CD player*  Furthermore, even if there is no specific AM/FM radio/CD player Important Points on Usage denotation of trademarks or registered E00735501033 trademarks, these are to be observed in E00708503550 their entirety. The audio system can only be used when the iPod/iPhone Playback Function ignition switch or the operation mode is in ON or ACC.
Page 304 AM/FM radio/CD player* 5th generation 5th generation 160GB (2009) 160GB (2007) 80GB (video) (video) 60GB 80GB 30GB 6th generation 5th generation 4th generation (video) 8GB 16GB (video camera) 8GB 16GB 8GB 16GB 3rd generation 2nd generation 1st generation (video) (aluminum) 1GB 2GB 4GB 4GB 8GB 2GB 4GB 8GB...
Page 305 AM/FM radio/CD player* 4th generation 3rd generation 2nd generation 1st generation 8GB 32GB 64GB 32GB 64GB 8GB 32GB 64GB 8GB 32GB 64GB 16GB 32GB 64GB 16GB 32GB 8GB 16GB 32GB 8GB 16GB 7-40 For pleasant driving...
Page 306: Handling Of Discs
Handling of Discs Handling of Discs Types of Disc That Can Be Important Points on Storage Played Back E00735901200  When not using discs, ensure these are This explains care that should be taken in the kept in cases, and stored out of direct sun- E00736001110 handling of discs.
Page 307: Audio Files (Mp3/Wma/Aac)
Audio Files (MP3/WMA/AAC)  8 cm discs may not be used.  Playback of other than standard CDs is Additionally, ensure you read the user manu-  Do not insert irregularly-shaped discs (for not guaranteed. Even if the audio can be als for your CD-R/RW drive and the writing example, heart-shaped), as these may played back, the audio quality cannot be...
Page 308 Audio Files (MP3/WMA/AAC) Speci- NOTE Name fica- Explanation ROOT  Depending on your computer’s operating Folder tion system, version, software, or settings, files Audio file may not have a file extension appended. In Format ISO96 Level Maximum 8 these cases, append the file extensions specifica- character file “.mp3”, “.wma”, or “.m4a”...
Page 309 Audio Files (MP3/WMA/AAC) “Motion Picture Experts Group”, and this is a Speci- Item Details video compression standard used in video Name fica- Explanation Sampling MPEG-1: 32/44.1/48 CDs, etc. tion frequency MPEG-2: 16/22.05/24 MP3 is one of the audio compression meth- File name Maximum 64 bytes (for Uni- [kHz]...
Page 310 Audio Files (MP3/WMA/AAC) format that has a higher compression ratio Item Details CAUTION than MP3. Bit rate [kbps] 48 to 320  AAC files different to the standards at right may not play back correctly, or file/folder Support NOTE names may not be displayed correctly. (variable bit rate) ...
Page 311: Important Points On Safety For The Customer
Important Points on Safety for the Customer Item Details WARNING WARNING Supported tag AAC tags or ID3 tags  The driver should not perform compli-  During thunderstorms, do not touch the information Title, Artist name, cated operations while driving. antenna or the front panel.
Page 312 Operation Keys Disc slot Disc *Label side Turn the power on, and resume playback Turn the PWR/VOL key clockwise to Push the disc in a certain amount, and the from the previous status. increase, and counter- clockwise to product will pull the disc in, and playback 2.
Page 313 Operation Keys Explanation of Buttons E00737501141 This explains names and functions of each part. 5- RADIO key 10- SCAN key Switch the radio and the band. For audio, play scan playback; for Use to eject a disc. 6- PWR/VOL key radio, scan for stations.
Page 314: Listen To Radio
Listen to Radio key/ Type 2 For audio, select audio track/file; for radio, perform automatic station selec- tion. 16- MENU key Switch to Menu mode. /SEL key Adjust audio quality and select items. For radio, manually select stations. Steering wheel audio remote 1- Volume up/down switch *: An iPod cable (available separately) is Adjust audio functions and the mobile...
Page 315 Listen to Radio Manual/Seek Station Selection NOTE Auto Preset  Press this button again while receiving the station to return to normal reception. The top 6 stations with a strong signal can be Turn the /SEL key to the frequency to lis- automatically registered in order with preset ten to.
Page 316: Listen To Cds
Listen to CDs Listen to CDs Switch Playback Mode Scan Playback (SCAN) E00737801216 Press the SCAN key. Repeat playback, random playback, and scan This explains how to listen to audio CDs playback are possible. (CD-DA/CD-TEXT). Play the first 10 seconds of each of the tracks on the whole disc in order.
Page 317 Listen to MP3s If a disc is already within the product, press Play the tracks in the folder in a random Repeat Playback (RPT) the MEDIA key to switch to CD as the order. source. Press the 1RPT key. NOTE NOTE Repeat playback of the track currently being ...
Page 318: Listen To An Ipod
Listen to an iPod* Files within the selected folder are dis- CAUTION NOTE played.  Do not leave the iPod/iPhone unattended in  When inserting removing 3. Turn the /SEL key to select the file. the vehicle. iPod/iPhone, for safety’s sake first stop the 4.
Page 319 Listen to an iPod* The selected source is indicated on the dis- 1. Turn the /SEL key to select the cate- NOTE play. gory.  Pressing again will cancel. 2. Press the /SEL key. Categories or Select the Track (File) tracks within the selected category are displayed.
Page 320: Listen To Audio Files On A Usb Device
Listen to Audio Files on a USB Device* Listen to Audio Files on a NOTE NOTE USB Device  Digital audio players that support the mass  Depending on the status of the vehicle and storage class specifications can be con- device, the iPod/iPhone may not play back E00736501535 nected.
Page 321 Listen to Audio Files on a USB Device* This enables selection of the next or previous Repeat playback of the tracks within the NOTE track. folder currently being played.  Even if the file is selected, all folder random playback will not be cancelled. NOTE Fast Forward or Rewind ...
Page 322: Display Indicator
Display Indicator Search Tracks NOTE NOTE  If there is no operation for five seconds after  While the folder is selected, press the 6 selecting the file, that file is played back. Search folders and files, and select a track. key to cancel track search mode.
Page 323 Display Indicator Change the Display Mode NOTE During MP3/WMA/AAC Play- back  Up to 11 characters may be displayed at one E00738501119 time. To display 12 or more characters, press You can change the content of the display the PAGE key, and subsequent characters indicator.
Page 324: Audio Quality And Volume Balance Adjustment
Audio Quality and Volume Balance Adjustment [DISP] Each time the key is pressed, this Adjust- Adjust Audio Quality and Vol- Turn counter- switches in the order “Album name”, “Track ment Turn clockwise ume Balance clockwise name”, “Artist name”, and “Operating sta- items tus”.
Page 325: Troubleshooting
Troubleshooting Settings Time Setting PHONE Settings Settings content value PHONE During mobile phone voice cut- Set the time manually. Change mobile phone voice cut-in settings. in, output audio from all speak- Depending on the type of vehicle, PHONE 1. Select “YES” at the “Adjust time” screen, ers.
Page 326 The drive has malfunctioned for some reason. Check that there is no problem with the disc, and insert the disc again. If the problem persists, con- sult an authorised MITSUBISHI MOTORS dealer. HEAT ERROR The temperature inside the product is high.
Page 327: Antenna
Antenna If You Think Something Is Not Working Properly... Here is a list of symptoms, causes and responses if you think something is not working properly. Symptoms Cause Response There is no sound or quiet The volume is turned to its minimum. Adjust the volume.
Page 328: Link System
Link System* NOTE  Be sure to remove the roof antenna in the following cases: • When going into an automatic car wash. • When placing a car cover over the vehicle. • When driving into a structure that has a low ceiling.
Page 329: Usb Input Terminal
USB input terminal* USB input terminal How to connect a USB memory Type 2 device E00761902051 Vehicles without E00762002020 DVD AUDIO You can connect your USB memory device or iPod* to play music files stored in the USB 1. Park your vehicle in a safe place and turn memory device or iPod.
Page 330 USB input terminal* 5. To remove the USB connector cable, turn Type 2 Type 1 the ignition switch to the “LOCK” posi- Vehicles with out tion or put the operation mode in OFF DVD AUDIO first and perform the installation steps in reverse.
Page 331: Hdmi Terminal
HDMI terminal* 4. Connect the connector cable to the USB For vehicles equipped with the AM/FM Type 2 input terminal. radio/CD player 5. To remove the connector cable, turn the ignition switch to the “LOCK” position or Refer to “Listen to an iPod” on page 7-53, put the operation mode in OFF first and “Listen to Audio Files on a USB Device”...
Page 332: Sun Visors
Sun visors Sun visors Vanity mirror Type 1 E00711202538 E00711301747 A vanity mirror is fitted to the back of the sun visor on the passenger side. 3. Connect a commercially available HDMI cable to the HDMI device. 4. Connect a HDMI cable to the HDMI ter- 1- To eliminate front glare minal.
Page 333: Cigarette Lighter
Cigarette lighter* Type 1 (fixed position) Type 2 (movable) To use the ashtray, pull it out. To use the movable ashtray, open the lid. Cigarette lighter E00711502573 The cigarette lighter can be used while the To remove the ashtray, pull it out while press- ignition switch is in either “ON”...
Page 334: Accessory Socket
Accessory socket* The cigarette lighter will automatically return CAUTION NOTE to its original position with a “click” when  When the cigarette lighter socket is used as a  Accessory sockets in 2 locations can be used ready. Pull it out for use. power source for an electric appliance, be at the same time.
Page 335: Usb Port (For Charging)
There are two USB ports (for charging) and have the vehicle checked by an author- If the USB connector cable does not insert in ised MITSUBISHI MOTORS dealer. located on the back of the floor console box. it firmly, it may become extremely hot and When using the USB port (for charging), the fuses may blow.
Page 336: Interior Lamps
Interior lamps Interior lamps Room lamps/Rear personal Rear (Type 2)* lamps E00712002793 E00712102879 Room lamps Front* Rear personal lamps 1- Front room & map lamps* 2- Rear room lamp* Rear personal lamps* NOTE Rear (Type 1)*  If you leave the lamps on without running the engine, you will run down the battery.
Page 337 Interior lamps Position Position Position of lamp On/off control of lamp On/off control of lamp On/off control switch switch switch  When the ignition switch is 2-DOOR Delayed off function Auto cut-out function () [Vehicles without central door turned to the “ON” position If the lamp is left switched on lock system] or the operation mode is put...
Page 338: Storage Spaces
15 seconds it goes off.  The time until the lamp goes off (delayed off) can be adjusted. For details, please con- sult an authorised MITSUBISHI MOTORS dealer.  The auto cut-out function cannot be operated when the room lamp switch is in the “ON” or “...
Page 339 Storage spaces Type 1 Type 3 NOTE  When the lamps are illuminated with the lamp switch in the “ ”, “ ”, or NOTE Type 2 “AUTO” position (vehicles with automatic  The centre console under tray is removable, lamp control), the glove box lamp illumi- so it is also possible to use as storage space.
Page 340 Storage spaces NOTE  When using a commercially available USB connector cable connected to the USB input terminal or commercially available HDMI connector cable connected to the HDMI input terminal, if you hold up extra length of the cable in the storage space and install the tray, you can use only the necessary length cable pulled out from the storage space.
Page 341: Cup Holder
Cup holder* CAUTION For the front seat  The holder should not be used to store any- thing heavier than sunglasses. These objects The cup holder is located between the front could drop out. seats. NOTE  The holder may not be able to accommodate every possible size and shape of sunglasses;...
Page 342: Bottle Holder
Bottle holder The bottle holders are provided at both sides of front and rear doors (if so equipped). NOTE Bottle holder  Do not hang heavy luggage (more than about 4 kg) on the hook. E00718201514 NOTE Doing so could cause damage to the hook. WARNING ...
Page 343: Coat Hook
Coat hook* CAUTION WARNING  Do not use the assist grips when getting into  Do not put a hanger or any heavy or or out of the vehicle. The assist grips could pointed object on the coat hook. If the cur- detach causing you to fall.
Page 344 For emergencies If the vehicle breaks down ...............8-2 If the operation mode cannot be changed to OFF (vehicles equipped with the keyless operation system) ....8-2 Emergency starting ................8-2 Engine overheating ................8-4 Bleeding the fuel system ..............8-5 Removal of water from the fuel filter ..........8-5 Tools, jack and jack handle ..............8-6 How to change a tyre ..............8-10 Towing ...................8-19...
Page 345: If The Vehicle Breaks Down
If the vehicle breaks down 1. Move the selector lever to the “P” If the vehicle breaks down CAUTION (PARK) position, and then change the  Do not attempt to start the engine by pulling operation mode to OFF. (For vehicles E00800101137 or pushing the vehicle.
Page 346 Emergency starting 4. Make sure battery electrolyte is at the NOTE WARNING proper level.  Open the terminal cover before connecting  Make sure that the connection is made Refer to “Battery” on page 10-9. the jumper cable to the positive (+) terminal to the appointed position (shown in the of the battery.
Page 347: Engine Overheating
 For vehicles equipped with the Auto Stop & Stop the engine immediately and contact Engine overheating Go (AS&G) system, press the “Auto Stop & an authorised MITSUBISHI MOTORS Go (AS&G) OFF” switch to deactivate the E00800604292 dealer for assistance.
Page 348: Bleeding The Fuel System
Bleeding the fuel system 5. Add coolant to the radiator and/or reserve Pump the hand pump (A) at the top of the fuel tank if necessary (refer to the “Mainte- filter until the hand pump becomes stiff. nance” section). Then try again to start the engine. If the engine does not start, repeat the process WARNING above.
Page 349: Tools, Jack And Jack Handle
If in doubt, consult your nearest author- driving, it indicates that water has accumu- 7 times in order to force the water out ised MITSUBISHI MOTORS dealer. lated in the fuel filter. If this occurs, remove through the drain plug (A).
Page 350 Tools, jack and jack handle C- Jack handle Single cab Single cab, Double cab Double cab 1- Wheel nut wrench Club cab 1- Tool bag 2- Wheel nut wrench A- Tool (wheel nut wrench) Removing and storing the tools, B- Jack handle jack and jack handle A- Tool (wheel nut wrench) C- Jack...
Page 351 Tools, jack and jack handle Club cab The tools are stored under the floor behind the passenger’s seat. The jack, and jack handle are stored under the floor behind the driver’s seat. 1. Open the rear door. Refer to “To open or close the rear door (Club cab)”...
Page 352 Tools, jack and jack handle 4. Remove the securing nut (C), and then 6. Reverse the removing procedure when 3. Remove the securing nut (C), and then take out the jack (D) on the right-hand storing the tools, jack and jack handle. take out the jack (D).
Page 353: How To Change A Tyre
How to change a tyre 3. While pressing the snap pin (F) on the To use the jack handle (Club assembled handle (E), insert the white- cab) marked handle (G) until it is locked by snap pin as illustrated. E00802401189 1.
Page 354 How to change a tyre On vehicles with automatic transmission, NOTE CAUTION move the selector lever to the “P” (PARK)  The chocks shown in the illustration do not  The pressure should be periodically checked position, and turn the ignition switch to come with your vehicle.
Page 355 How to change a tyre 3. Securely insert the pin (C) on the jack CAUTION handle into the holder (D) of the spare  When removing the spare wheel, please wheel carrier. observe the followings. If you do not follow them, it could result in break the spare wheel carrier.
Page 356 How to change a tyre 2. Turn the securing bolt (B) anticlockwise To change a tyre with the wheel nut wrench to lower the E00803202729 spare wheel completely to the ground and 1. Loosen the wheel nuts a quarter turn with to slack the chain.
Page 357 How to change a tyre NOTE  When jacking up the rear of the vehicle, turn the tip of the jack so that the grooved portion (D) properly meets the designated point. A- Front jacking point (vehicles for 2WD) C- Rear jacking point WARNING 2WD Hi-Rider, 4WD 3.
Page 358 How to change a tyre 5. Move the jack handle up and down to WARNING raise the ram until just before the jack  Do not use a jack except the one that came contacts the jacking point of the vehicle. with your vehicle.
Page 359 How to change a tyre 8. Turn the wheel nuts clockwise by hand to Type 2 initially tighten them. [Type 1: On vehicles with steel wheels] Temporarily tighten the wheel nuts by hand until the tapered parts of the wheel nuts make light contact with the seats of the wheel holes and the wheel is not loose.
Page 360  Never use your foot or a pipe extension for ised MITSUBISHI MOTORS dealer. extra force in the wheel nut wrench. If you  Do not mix one type of tyre with another or do so, you will tighten the nut too much.
Page 361 How to change a tyre 4. Have your damaged tyre repaired as soon To store the spare wheel NOTE as possible.  Confirm that the hanger disc is securely fit- E00803701785 ted in the wheel disc hole when the wheel is Type 1 Type 2 just lifted off the ground.
Page 362: Towing
MITSUBISHI MOTORS dealer or a com- 22 N•m (achieved by applying a force of mercial tow truck service. 100 N at the end of the wheel nut In the following cases, transport the vehicle wrench)).
Page 363 Towing ised MITSUBISHI MOTORS dealer or a CAUTION commercial tow truck service for assistance.  On 4WD vehicles, transport the vehicle with the driving wheels on a carriage (Type D or Only when you cannot receive a towing ser- E) as illustrated. Never try to tow with the...
Page 364 Towing down strap. Never place the ignition switch in CAUTION 2WD Hi-Rider, 4WD the “LOCK” position or put the operation  On vehicles with manual transmission, do mode in OFF when towing. not tow the vehicle with the rear wheels on the ground (Type B) as illustrated.
Page 365 Towing 2. Keep the engine running. 6. During towing make sure that close con- WARNING If the engine is not running, perform the tact is maintained between the drivers of  When the engine is not running, the brake following operation to unlock the steering both vehicles, and that the vehicles travel booster and power steering pump do not wheel.
Page 366: Operation Under Adverse Driving Conditions
 When the vehicle with an automatic trans-  Avoid high-speed operation, sudden MITSUBISHI MOTORS dealer and take mission is to be towed by another vehicle acceleration, abrupt brake application and the necessary measures or repair. with the all wheels on the ground, make sure sharp cornering.
Page 367 Operation under adverse driving conditions CAUTION  Do not press the accelerator pedal rapidly. If the wheels break free of the ice, the vehicle could suddenly start moving and possibly cause an accident. On a bumpy or rutted road Drive as slow as possible when driving on bumpy or rutted roads.
Page 368 Vehicle care Vehicle care precautions ..............9-2 Cleaning the interior of your vehicle ..........9-2 Cleaning the exterior of your vehicle ..........9-3...
Page 369 Vehicle care precautions Vehicle care precautions Cleaning the interior of your Plastic, vinyl leather, fabric and flocked parts vehicle E00900102005 In order to maintain the value of your vehicle, E00900301563 E00900201719 1. Lightly wipe these off with a soft cloth it is necessary to perform regular mainte- After cleaning the interior of your vehicle soaked in a mild soap and water solution.
Page 370 Cleaning the exterior of your vehicle Use a vacuum cleaner and brush to clean the paint coat and body of your vehicle if left NOTE the seats. If stained, vinyl and synthetic in prolonged contact.  Remove dirty patches or oil substances leather should be cleaned with an appro- Frequent washing and waxing is the best way quickly as they can stain genuine leather.
Page 371 Cleaning the exterior of your vehicle After washing your vehicle, wipe off all CAUTION CAUTION waterdrops from the rubber parts around the  Never spray or splash water on the electrical • The outside rear-view mirrors are retracted. doors to prevent the doors from freezing. components in the engine compartment.
Page 372 Cleaning the exterior of your vehicle the glass, wipe it dry with a clean, dry, soft Cleaning plastic parts Aluminium wheels* cloth. Never use a cloth that is used for clean- E00901301935 E00901500347 ing a painted surface to clean a window. Wax 1.
Page 373 Cleaning the exterior of your vehicle If salt and other chemicals are used on the roads in your area, clean the engine compart- ment at least every three months. Never spray or splash water on the electrical components in the engine compartment, as this may cause damage.
Page 374 Maintenance Service precautions ................10-2 Catalytic converter .................10-3 Bonnet ....................10-3 Engine oil ..................10-5 Engine coolant ................10-6 Washer fluid ...................10-7 Brake fluid ..................10-7 Clutch fluid* ...................10-8 Power steering fluid ...............10-9 Battery ....................10-9 Tyres ....................10-11 Wiper blade rubber replacement ..........10-15 General maintenance ..............10-16 Fusible links .................10-17 Fuses ....................10-17 Replacement of lamp bulbs ............10-21...
Page 375: Service Precautions
 When checking or servicing the inside of your personal safety. Consult an author- the engine compartment, make sure the ised MITSUBISHI MOTORS dealer for engine is switched off and has had a necessary information. chance to cool down.
Page 376: Catalytic Converter
Catalytic converter Check items of engine compartment are located as shown in the figure below. 4D56 4N15 The catalytic converter is installed in the 1. Engine coolant reservoir NOTE exhaust system. 2. Brake fluid reservoir  Use fuel of the type recommended in “Fuel It is important to keep the engine properly 3.
Page 377 Bonnet 3. Support the bonnet by inserting the sup- port bar in its slot. 2. Raise the bonnet while pressing the safety 2. Slowly lower the bonnet to a position lock. about 20 cm above the closed position, then let it drop. CAUTION 3.
Page 378: Engine Oil
Engine oil The engine oil used has a significant effect on Engine oil NOTE the engine’s performance, service life and  The engine oil will deteriorate rapidly if the startability. Be sure to use oil of the recom- E01000404853 vehicle is subjected to severe conditions, mended quality and appropriate viscosity.
Page 379: Engine Coolant
If this occurs, have based non-silicate, non-amine, non- the system checked at an authorised nitrate and non-borate coolant with long MITSUBISHI MOTORS dealer as soon as life hybrid organic acid technology Engine coolant possible. If the level should drop below the “L” (LOW)
Page 380: Washer Fluid
Washer fluid The concentration should be checked before CAUTION During cold weather the start of cold weather and anti-freeze  Do not use alcohol or methanol anti-freeze or added to the system if necessary. any engine coolants mixed with alcohol or To ensure proper operation of the washers at methanol anti-freeze.
Page 381: Clutch Fluid
 Keep the reservoir tank cap closed to prevent the brake system. your authorised MITSUBISHI MOTORS the brake fluid from deteriorating except If this occurs, have the vehicle checked by an dealer and repaired immediately.
Page 382: Power Steering Fluid
Also, do not short-circuit the bat- Fluid type tery terminals. Doing so could create sparks. The battery emits highly explosive hydro- Use “MITSUBISHI MOTORS GENUINE gen gas. Ventilate when charging the bat- PSF (Power Steering Fluid)”. tery in an enclosed space. Maintenance...
Page 383 Battery Check the electrolyte level at least once every positive (+) terminal and then the negative WARNING four weeks, depending on the operating con- (−) terminal.  Keep away from children ditions. If the battery is not used, it will discharge by NOTE itself with time.
Page 384: Tyres
Tyres WARNING NOTE  Ventilate when charging or using the bat-  Keep the terminals clean. After the battery is tery in an enclosed space. connected, apply terminal protection grease. To clean the terminals, use lukewarm water.  Check to see if the battery is securely CAUTION installed and cannot be moved during travel.
Page 385 Tyres Tyre inflation pressures E01001404788 No cargo Cargo Tyre size Front Rear Front Rear 220 kPa 220 kPa 220 kPa 290 kPa 265/60R18 110H (32 p.s.i/ 2.2 kgf/cm²) (32 p.s.i/ 2.2 kgf/cm²) (32 p.s.i/ 2.2 kgf/cm²) (42 p.s.i/ 2.9 kgf/cm²) 220 kPa 220 kPa 220 kPa...
Page 386 2- Tread wear indicator severe braking. Consult your authorised MITSUBISHI MOTORS dealer to determine Replacing tyres and wheels Check the tyres for cuts, cracks and other the cause of irregular tread wear.
Page 387 Tyres CAUTION Snow tyres Spare tyre used  If the tyres have arrows (A) indicating the E01002000549 correct direction of rotation, swap the front The use of snow tyres is recommended for and rear tyres on the left hand side of the driving on snow and ice.
Page 388: Wiper Blade Rubber Replacement
Wiper blade rubber replacement On 4WD vehicles in which the driving power 2. Pull the wiper blade until its stopper (A) CAUTION is distributed preferentially to the rear wheels, disengages from the hook (B). Pull the  Drive carefully and do not exceed 30 km/h. ensure that the tyre chains are fitted on the wiper blade further to remove it.
Page 389: General Maintenance
MOTORS smell fuel, do not operate the vehicle; call dealer for inspection. 5. Push the wiper blade until the hook (B) your authorised MITSUBISHI MOTORS engages securely with the stopper (A). dealer for assistance. Hinges and latches lubrication Check all latches and hinges, and, if neces- sary, have them lubricated.
Page 390: Fusible Links
In case of a melted fusible link, see your authorised MITSUBISHI MOTORS dealer for inspection and replacement. For the fusible links, please refer to “Passen- ger compartment fuse location table” on page 10-18 and “Engine compartment fuse loca-...
Page 391 Fuses Sym- Capac- Engine compartment Passenger compartment fuse loca- Electrical system tion table In the engine compartment, the fuse block is Control unit 7.5 A E01007902286 located as shown in the illustration. Rear fog lamp 10 A Central door lock 15 A Room lamp 15 A...
Page 392 Fuses  Some fuses may not be installed on your Electrical sys- Capac- Behind of the fuse block cover Symbol vehicle, depending on the vehicle model ities or specifications.  The table above shows the main equip- 30 A DC(AUDIO) ment corresponding to each fuse.
Page 393 Fuses Electrical sys- Capac- Electrical sys- Capac- Capacity Colour Symbol Symbol ities ities 15 A Blue Headlamp high AC inverter 20 A 20 A Yellow 10 A beam (left) — Spare fuse 20 A Green (fuse type) / Pink (fusible 30 A Headlamp high link type)
Page 394: Replacement Of Lamp Bulbs
 Never use a fuse with a capacity larger than your vehicle checked by an authorised that specified or any substitute, such as wire, MITSUBISHI MOTORS dealer. foil, etc.; doing so will cause the circuit wir- ing to heat up and could cause a fire.
Page 395 (PY21W)  Front these procedures be carried out by an author- 7- Daytime running lamps: 13 W ised MITSUBISHI MOTORS dealer. (P13W)  Be careful not to scratch the vehicle body Halogen headlamps type 8- Type 1 when removing a lamp and lens.
Page 396  The high-mounted stop lamp uses an LED Type A instead of the bulb. If you need to repair or replace the lamp, contact an authorised MITSUBISHI MOTORS dealer. Type B Type 1 Type 2 1- Position lamps/Daytime running lamps: －...
Page 397 Replacement of lamp bulbs 4- Rear turn-signal lamps: 21 W Inside Headlamps (PY21W) E01003403987 E01003502747 5- Reversing lamps: 18 W (W16W) 6- High-mounted stop lamp*: － Vehicles with halogen headlamps Type 1 Type 2 Type 3 7- Licence plate lamps: 5 W (W5W) Codes in parentheses indicate bulb types.
Page 398 Replacement of lamp bulbs NOTE  When moving the upper cover towards the rear of the vehicle, remove the harness from the air cleaner hooks (C). 3. Turn the cover (E) anticlockwise to 5. To install the bulb, perform the removal remove it.
Page 399 Replacement of lamp bulbs NOTE  When moving the upper cover towards the rear of the vehicle, remove the harness from the air cleaner hooks (C). 3. Turn the cover (E) anticlockwise to 5. To install the bulb, perform the removal remove it.
Page 400 Replacement of lamp bulbs NOTE  After replacing the bulb, make sure that the hinges at the front of the vehicle are firmly set. *: Front of the vehicle *: Front of the vehicle 4. Turn the bulb socket (F) anticlockwise to 2.
Page 401 Replacement of lamp bulbs Front turn-signal lamps Front fog lamps/Daytime run- ning lamps E01003802708 1. To create enough work space, turn the E01004003850 steering wheel all the way in the direction opposite to the side you wish to replace. Vehicles with halogen headlamps 2.
Page 402 Replacement of lamp bulbs NOTE Type 1 Type 2 Type 3  When refitting the clip (B), first insert part (H) of the clip into the hole and then press part (I) into it. D- Front fog lamp *: Front of the vehicle E- Daytime running lamp 3.
Page 403 Replacement of lamp bulbs 4. [Daytime running lamp] 3. Move the lamp unit toward the rear of the NOTE Turn the socket (D) anticlockwise to vehicle and remove the clips (B).  When refitting the clip (B), first insert part remove it, and while holding down the tab (J) of the clip into the hole and then press Type A...
Page 404 Replacement of lamp bulbs 5. To install the bulb, perform the removal Type A steps in reverse. NOTE  When mounting the lamp unit for Type A, align the pins (F) and clip (G) on the lamp unit with the holes (H) in the body. NOTE Type B ...
Page 405 Replacement of lamp bulbs 3. To install the bulb, perform the removal Except for vehicles with rear circulator NOTE steps in reverse.  When installing the lens, align the tab (A) on the lens with the holes on the vehicle side. NOTE ...
Page 406 Replacement of lamp bulbs Rear room lamp (Type 1), Rear Type 2 Type 1 personal lamps (Type 2), Room lamp (Type 3) E01004901523 Type 1, Type 2 1. Insert a straight blade (or minus) screw- driver into the notch of the lens and pry gently to remove it.
Page 407  Wrap a piece of cloth around the tip of the screwdriver in order to avoid scratching the lens. Glove box lamp 2. To install the bulb, perform the removal steps in reverse. E01006101499 Have the glove box lamp bulb replaced at an authorised MITSUBISHI MOTORS dealer. 10-34 Maintenance...
Page 408 Specifications Vehicle labelling ................11-2 Vehicle dimensions ................11-3 Vehicle performance ..............11-9 Engine specifications ..............11-12 Electrical system ................11-12 Tyres and wheels ................11-13 Capacity ..................11-13...
Page 409: Vehicle Labelling
Vehicle labelling Vehicle labelling 4D56 E01100105614 Vehicle Identification Number: (VIN) The vehicle identification number is stamped as shown in the illustration. 4N15 Engine model/number The engine model and number are stamped on the engine cylinder block as shown in the illustrations.
Page 410: Vehicle Dimensions
Vehicle dimensions Vehicle dimensions E01100205426 Single cab Specifications 11-3...
Page 411 Vehicle dimensions Single cab Item Front track 1,520 mm Overall width 1,815 mm Front overhang 880 mm Wheel base 3,000 mm, 2,800 mm* Rear overhang 1,215 mm, 1,295 mm* Overall length 5,095 mm 5,095 mm, 4,895 mm* , 5,175 mm* Ground clearance (unladen) 200 mm Overall height (unladen)
Page 412 Vehicle dimensions Club cab Specifications 11-5...
Page 413 Vehicle dimensions Club cab Item 2WD Hi-Rider Front track 1,520 mm Overall width 1,815 mm Front overhang 880 mm Wheel base 3,000 mm Without rear bumper 1,330 mm Rear overhang With rear bumper 1,410 mm Without rear bumper 5,210 mm Overall length With rear bumper 5,290 mm...
Page 414 Vehicle dimensions Double cab Specifications 11-7...
Page 415 Vehicle dimensions Double cab Item 2WD Hi-Rider Front track 1,520 mm 1,520 mm Overall width 1,815 mm 1,815 mm Front overhang 880 mm 880 mm Wheel base 3,000 mm 3,000 mm Without rear bumper 1,340 mm − Rear overhang With rear bumper −...
Page 416: Vehicle Performance
Vehicle performance Vehicle performance E01100304387 Single cab Item Maximum speed 165 km/h 169 km/h Club cab 2WD Hi-Rider Item Maximum speed 165 km/h 179 km/h 177 km/h Double cab 2WD Hi-Rider, 4WD Item Maximum speed 165 km/h 179 km/h 177 km/h Specifications 11-9...
Page 417: Engine Specifications
 The vehicles equipped with Auto Stop & Go (AS&G) system have a dedicated AS&G battery type. Use of a different battery could cause the battery to run down quickly or AS&G system not to operate normally. Please contact an authorised MITSUBISHI MOTORS dealer when replacing the battery. 11-12...
Page 418: Tyres And Wheels
Size 15x6J 16x6JJ 16x6J 16x7J, 16x7JJ 17x7 1/2J 18x7 1/2J Wheel Offset (Inset) 38 mm NOTE  Contact your MITSUBISHI MOTORS dealer for details on the combination used on your vehicle. Capacity E01101308018 4D56 4N15 (M/T) 4N15 (A/T) Specifications 11-13...
Page 419 0.1 litre Washer fluid 4.2 litres — Automatic transmission fluid 10.4 litres MITSUBISHI MOTORS GENUINE ATF-PA CAUTION  For the Automatic transmission fluid, use only the MITSUBISHI MOTORS GENUINE ATF. Use of a different fluid could damage the transmission. 11-14 Specifications...
Page 420 Capacity Item Quantity Lubricants MITSUBISHI MOTORS GENUINE MTF API GL-3 SAE 5M/T 2.3 litres 75W-85 Manual trans- MITSUBISHI MOTORS GENUINE NEW MULTI GEAR 6M/T 2.2 litres mission oil OIL ECO API GL-4, SAE 75W-80 MITSUBISHI MOTORS GENUINE NEW MULTI GEAR 6M/T 2.2 litres...
Page 422 E09300104686 Information for station service Except for short wheel base 75 litres vehicles Capacity Short wheel base vehicles 68 litres Fuel Cetane number (EN590) Recommended fuel 51 or higher Refer to the “General information” section for the fuel selection. Engine oil Refer to the “Maintenance”...

Mitsubishi MOTORS Triton Owner's Manual

General Information 2

Locking and Unlocking 3

Seat and Seat Belts 4

Section 4

Section 5

Section 6

For Emergencies

Maintenance

Quick Links

Chapters

Troubleshooting

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Mitsubishi MOTORS Triton

Summary of Contents for Mitsubishi MOTORS Triton