Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Active Audio Ray-On B70 PoE
Summary of Contents for Active Audio Ray-On B70 PoE
- Page 1 Manual Ray-On For column models B70 PoE, R70 PoE, R110 PoE...
- Page 2 User Manual – Ray-On PoE series 2 sur 22 DOP1066_A...
-
Page 3: Table Of Contents
User Manual – Ray-On PoE series Table of contents Introduction ..............................5 Positioning ..............................6 2.1. R70 PoE and R110 PoE ......................... 6 B70 PoE ..............................7 Integration of the column in the network ................... 8 PoE technology ............................ 8 PoE+ network verification ........................ - Page 4 For your safety, please read this manual before any intervention on Ray-On PoE speakers. If in doubt, contact your reseller or Active Audio (info@activeaudio.fr). For your safety, please follow the instructions listed below to avoid the risk of electric shock, fire, or damage to the product and its environment.
-
Page 5: Introduction
DGRC method makes it possible to decrease the number of channels to be controlled, thereby enhancing economic efficiency. The Ray-On B70 PoE sound bar is designed for the sound reinforcement of narrow spaces such as corridors, escalators, shopping alleys, shopping malls, railway platforms…... -
Page 6: Positioning
User Manual – Ray-On PoE series 2. Positioning 2.1. R70 PoE and R110 PoE The most important parameter for the installation of Ray-On+ loudspeaker is its mounting height because the range of the column directly depends on it. Installing the column higher will increase the range but will affect SPL. On the contrary, installing the column lower will increase SPL, but decreases its range. -
Page 7: B70 Poe
User Manual – Ray-On PoE series B70 PoE The B70 sound bar is horizontally mounted, above the area to be sounded in transverse direction as shown in figure 3. The width of the zone to be sounded and the recommended space between the loudspeakers is given by the mounting height. -
Page 8: Integration Of The Column In The Network
User Manual – Ray-On PoE series Integration of the column in the network Before connecting Ray-On PoE, on the network, it is necessary to check that it is compatible with PoE+ technology and that it has the characteristics allowing to obtain the perfect functioning of Ray-On PoE. PoE technology The PoE technology described by the IEEE802.3 standard enables a device connected to an Ethernet network to be supplied from the network cable. -
Page 9: Wiring
User Manual – Ray-On PoE series • PoE+ injectors In the case where switches that do not have the PoE+ function are already present on the installation, it is possible to position a PoE injector between the switch and the cable connected to the enclosure. -
Page 10: Setting
User Manual – Ray-On PoE series Setting Ray-On PoE has a DANTE standard digital audio input. Ray-On PoE must therefore be connected to a network comprising all the elements enabling DANTE to operate. The commissioning and configuration of Ray-On PoE requires connecting a computer equipped with DANTE CONTROLLER software to the network. - Page 11 User Manual – Ray-On PoE series Locating the speakers Connect the speakers one by one on the network. After each connection : • Check that the speaker is correctly connected to the network. If the speaker is correctly connected to the network, the configuration of the LEDs located at the RJ45 connector on the speaker is as follows : 11 sur 22 DOP1066_A...
- Page 12 User Manual – Ray-On PoE series • Then access the Device View in DANTE CONTROLLER. Menu -> Device -> Device View The Receive tab allows you to view the device connected to the speaker, the connection status as well as the presence of a signal. 12 sur 22 DOP1066_A...
- Page 13 User Manual – Ray-On PoE series • After having refreshed the equipment connected in DANTE CONTROLLER (F5 key), the speaker must appear by its address, at the Status tab. 13 sur 22 DOP1066_A...
- Page 14 User Manual – Ray-On PoE series • In the Device tab, you can rename the enclosure if necessary in DANTE CONTROLLER. You can change the sample rate to subscribe to another device. Two connected devices must have the same sample rate. •...
-
Page 15: Technical Drawings
User Manual – Ray-On PoE series 5. Technical drawings 5.1. R70 PoE and R110 PoE Ray-On 70 PoE and 110 PoE loudspeakers are vertically mounted, usually on a wall, using the supplied wall-mounting system. See also figure 9 for the technical drawings of the wall-mounting system. -
Page 16: B70 Poe
User Manual – Ray-On PoE series 5.2. B70 PoE B70 PoE is horizontally mounted, usually on a wall or hanged from the ceiling, using the supplied mounting systems. See also figure 11 for the technical drawings of the mountings system. Figure 10 : Mechanical drawings Fixation dimensions Figure 11 : General and back view of fixation... -
Page 17: Specifications
User Manual – Ray-On PoE series 6. Specifications B70 PoE Acoustical data Electrical data Range ±3dB 6,5m Amplifier type Class-D amplifier Range ±5dB Max output power 250W Max SPL 94dB at 5m (108dB at 1m) Power supply RJ45 Tilting angle of audience area 0°-5°... -
Page 18: Acoustical Data
User Manual – Ray-On PoE series 7. Acoustical data All data presented below are obtained with columns in their nominal position and using nominal filtering parameters. a. R70 PoE acoustical data Figure 12 : R70 PoE directivity : sound level for the voice octaves (500Hz, 1kHz, 2kHz) Left : horizontal, Right : vertical Figure 13 : R70 PoE : Frequency response @1W at reference point* (left),... -
Page 19: R110 Poe Acoustical Data
User Manual – Ray-On PoE series b. R110 PoE acoustical data Figure 14 : R110 PoE directivity : sound level for the voice octaves (500Hz, 1kHz, 2kHz) Left : horizontal, Right : vertical Figure 15 : R110 PoE : Frequency response @1W at reference point* (left), Impedance (right) *0dB corresponds to the efficiency (dB / 1W the reference point) 19 sur 22... -
Page 20: B70 Poe Acoustical Data
User Manual – Ray-On PoE series c. B70 PoE acoustical data Figure 16 : Horizontal and vertical polar curves of B70 PoE Figure 17 : Frequency response (left), Impedance (right) 20 sur 22 DOP1066_A... -
Page 21: Declaration Of Conformity
User Manual – Ray-On PoE series 8. Declaration of conformity ACTIVE AUDIO SAS, 332 Boulevard Marcel Paul 44800 St Herblain, France, Declares under our sole responsibility that the following products B70 PoE, R70 PoE, R110 PoE Comply with the council directive 2004/108/CE... - Page 22 User Manual – Ray-On PoE series www.activeaudio.fr info@activeaudio.fr Tel: +33 (0)2 40 46 66 64 22 sur 22 DOP1066_A...
Need help?
Do you have a question about the Ray-On B70 PoE and is the answer not in the manual?
Questions and answers