Cycle Selection Charts - Whirlpool DU1015 Use And Care Manual

Use cycles or options that add extra heat to the wash or rinse
portion of the cycle only when needed.
Run your dishwasher with full loads. Run a rinse cycle after
meals until the dishwasher is full.
If your home is equipped with a water softener, you may want
to avoid starting the dishwasher during the regeneration of
the softener, since this may contribute to poor wash
performance.

Cycle Selection Charts

Select the wash cycle and options desired and press START/
RESUME. The dishwasher starts filling once you press START/
RESUME, unless you select a delay wash. You can change
cycles and options as the machine is filling.
After completing a wash cycle, the dishwasher remembers the
cycle and options. It uses the same cycle and options again in
the next wash cycle, if you press only START/RESUME.
NOTE: If the door is opened during a cycle or the power is
interrupted, the Start/Resume indicator flashes. The cycle will not
resume until the door is closed and Start/Resume is pressed.
A " " shows what steps are in each cycle. Your model may have
some or all of the cycles shown.
Display time is for models with the dual digit display on the
console.
These models meet the ENERGY STAR
efficiency.
Temperatures indicate where extra heat is added. The cycle
countdown (on some models) pauses at these points until water
reaches the temperature.
Water usage is shown in U.S. gallons/liters.
Pots & Pans
Use this cycle for hard-to-clean, heavily soiled pots, pans,
casseroles, and regular tableware. During the wash, the wash
action will repeatedly pause for several seconds.
Initial display time after rotating clock pattern: 92-99 min.
Use both detergent dispenser sections.
Pre- Main Rinse Rinse
Wash Wash
140°F
(60°C)
® guidelines for energy
Final Dry Mini- Water
Heated mum Usage
Rinse Time (gal/L)
(min)
99* 6.9-7.8/
140°F Light 26.1-29.6
(60°C) soil
Normal
Use this cycle for loads with normal amounts of food soil. (The
energy-usage label is based on this cycle.) During the wash, the
wash action will repeatedly pause for several seconds.
Initial display time after rotating clock pattern: 64-84 min.
Use both detergent dispenser sections.
Pre- Main Purge Rinse
Wash Wash
120°F
(49°C)
Light (on some models)
Use this cycle for lightly soiled items or china and crystal.
During the wash, the wash action will repeatedly pause for
several seconds.
Initial display time after rotating clock pattern: 68-81 min.
Use main detergent dispenser section.
Rinse Main Purge Rinse
Wash
120°F
(49°C)
GLASS XPRESS™ cycle (on some models)
Use this cycle to quickly wash prerinsed glasses or dish loads.
This cycle does not dry.
NOTE: Time and water use do not vary in this cycle.
Initial display time after rotating clock pattern: 29 min.
Use main detergent dispenser section.
Pre- Main Rinse Rinse
Wash Wash
Rinse Only
Use this rinse cycle for rinsing dishes, glasses, and silverware
that will not be washed right away.
Initial display time after rotating clock pattern: 3 min.
Do not use detergent with this cycle.
Pre- Main Rinse Rinse
Wash Wash
*If the incoming water is less than the recommended temperature
or food soils are heavy, the cycle will automatically compensate
by adding time, heat, and water as needed.
Final Dry Mini- Water
Heated mum Usage
Rinse Time (gal/L)
(min)
71* 5.6-6.8/
140°F Light 21.2-25.7
(60°C) soil
Final Dry Mini- Water
Heated mum Usage
Rinse Time (gal/L)
(min)
77* 5.9-6.8/
135°F cycled Light 22.3-25.7
(57°C) soil
Final Dry Mini- Water
Heated mum Usage
Rinse Time (gal/L)
(min)
30 6.9/26.0
Final Dry Time Water
Heated (min) Usage
Rinse (gal/L)
10 1.8-/6.8
13