Download Print this page

Omnitron Systems iConverter XM5 Quick Start Manual

Network interface device

Advertisement

Quick Links

iConverter
XM5
®
Network Interface Device
Quick Start Guide
38 Tesla, Irvine, CA 92618 USA
Phone: (949) 250-6510; Fax: (949) 250-6514
General and Copyright Notice
This publication is protected by U.S. and international copyright laws. All rights reserved.
The whole or any part of this publication may not be reproduced, stored in a retrieval
system, translated, transcribed, or transmitted, in any form, or by any means, manual,
electric, electronic, electromagnetic, mechanical, chemical, optical or otherwise, without
prior explicit written permission of Omnitron Systems Technology, Inc.
The following trademarks are owned by Omnitron Systems Technology, Inc.: FlexPoint
FlexSwitch
, HybridNID
, iConverter
TM
®
OmniConverter
, RuggedNet
, Omnitron Systems Technology, Inc.
®
®
Omnitron logo.
All other company or product names may be trademarks of their respective owners.
The information contained in this publication is subject to change without notice. Omnitron
Systems Technology, Inc. is not responsible for any inadvertent errors.
Warranty
This network product and the included AC/DC power adapter are warranted to the
original purchaser (Buyer) against defects in material and workmanship for a period of
two (2) years from the date of shipment. The warranty for the network product can be
extended to three (3) years by registering the product at www.omnitron-systems.com/
support within ninety (90) days from the date of shipment. During the warranty period,
Omnitron will, at its option, repair or replace a product which is proven to be defective
with the same product or with a product with at least the same functionality.
For warranty service, the product must be sent to an Omnitron designated facility, at
Buyer's expense. Omnitron will pay the shipping charge to return the product to Buyer's
designated US address using Omnitron's standard shipping method.
Limitation of Warranty
The foregoing warranty shall not apply to product malfunctions resulting from improper
or inadequate use and/or maintenance of the equipment by Buyer, Buyer-supplied
equipment, Buyer-supplied interfacing, unauthorized modifications or tampering with
equipment (including removal of equipment cover by personnel not specifically authorized
and certified by Omnitron), or misuse, or operating outside the environmental specification
of the product (including but not limited to voltage, ambient temperature, radiation,
unusual dust, etc.), or improper site preparation or maintenance.
No other warranty is expressed or implied. Omnitron specifically disclaims the implied
warranties of merchantability and fitness for any particular purpose.
The remedies provided herein are the Buyer's sole and exclusive remedies. Omnitron
shall not be liable for any direct, indirect, special, incidental, or consequential damages,
whether based on contract, tort, or any legal theory.
, miConverter
, NetOutlook
, OmniLight
®
TM
®
, OST
TM
TM
Page 2
,
TM
,
®
and the

Advertisement

loading

Summary of Contents for Omnitron Systems iConverter XM5

  • Page 1 Omnitron Systems Technology, Inc. The following trademarks are owned by Omnitron Systems Technology, Inc.: FlexPoint FlexSwitch , HybridNID...
  • Page 2: Product Overview

    The XM5 features a RS-232 Serial Console Port (aka Craft Interface) which can be Address: Omnitron Systems Technology, Inc. connected to a computer for initial setup and configuration. The Serial Console Port is accessed through the a RJ-45 port on the back of the module.
  • Page 3: Installation Procedure

    RJ-45 Ports The RJ-45 Ethernet ports support 10BASE-T, 100BASE-TX and 1000BASE-T protocols, auto-negotiation, auto MDI/MDI-X crossover and can be manually forced to a specific speed and duplex mode using the port command. SFP/SFP+/XFP Ports The SFP interfaces (P4 - P7) support SERDES 100BASE-X or 1000BASE-X fiber Clock I/O transceivers and SGMII 10/100/1000BASE-T copper transceivers.
  • Page 4: Rack Mounting

    Function OFF (DOWN) OFF (DOWN) ZTP process is disabled ON (UP) OFF (DOWN) Listen Mode OFF (DOWN) ON (UP) Activate Mode ON (UP) ON (UP) Standard Mode ZTP Options Zero Touch is disabled by default. The ZTP process is configured by setting these DIP- switches to the desired mode of operation..
  • Page 5: Connect Cables

    4) Connect Cables WARNING: Only a DC power source that complies with Insert the fiber or copper transceivers into the 10G/1G receptacles on the module. safety extra low voltage (SELV) requirements can be connected to the DC-input power supply. NOTE: The release latch of the transceiver must be in the closed (up) position before insertion.
  • Page 6: Verify Operations

    Once the module has booted, an Entry screen will be displayed on the attached PC. If Specifications a password has been configured, enter the password and press <ENTER>. A system iConverter prompt, ‘>’, will be displayed. At the module prompt (>), enter ?, help or h to view the Description 10G Network Interface Device command options.