Advertisement

5H80
Congratulations and thank you for the purchase of your Rubbermaid 7' x 7' storage building. Before you begin assembly please
be sure to check your local building codes, ordinances and restrictions, and applicable neighborhood governances.
BEFORE YOU BEGIN – SURFACE PREPARATION
To ensure proper assembly and performance your shed needs to be built on a solid, level surface. A cement or patio surface, or
a treated-wood platform is recommended.
BEFORE YOU BEGIN – LOCATION
When choosing a location in your yard make sure you choose an area with easy access and one that provides proper drainage
for water to run away from the shed location.
Prior to beginning the assembly please complete the following items:
• Thoroughly review all assembly steps (it is important that the steps are followed in the correct order).
• Review the parts list and make sure that no parts are missing.
IMPORTANT – DO NOT
RETURN TO THE STORE
For assistance with your
Rubbermaid
Storage Building
®
or for additional product
information call our toll-free
Consumer Service number:
1-888-895-2110
M–F 8:30AM to 5:00PM EST
or visit us online at:
www.rubbermaid.com.
94¼"
85½"
84"
1821375

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 5H80 and is the answer not in the manual?

Questions and answers

James Syput
May 27, 2025

I need 2 skylights for my 5h80 Rubbermaid shed they got damaged from a hail storm

1 comments:
Mr. Anderson
May 27, 2025

To replace the skylights on a Rubbermaid 5H80 shed:

1. Use a screwdriver to punch out the screw holes around the skylight openings on the upper roof panels.
2. Remove the existing screws (AA) and the old skylights from the Upper Roof Panel (P).
3. Position the new skylights (L) in place on the Upper Roof Panel (P).
4. Fasten each skylight using 8 screws (AA) per skylight (16 screws total).
5. Repeat the process for the second Upper Roof Panel (N).
6. Do not overtighten the screws during installation.

Make sure the shed is on a level surface and follow the instructions in order.

This answer is automatically generated

Sharon Bannon
April 15, 2025

Can I still order missing parts? Model 5H80

1 comments:
Mr. Anderson
April 15, 2025

Yes, you can order missing parts for the Rubbermaid model 5H80.

This answer is automatically generated

Swain joseph
May 14, 2025

Hi I need a shed skylight (L) and gasket

Summary of Contents for Rubbermaid 5H80

  • Page 1 5H80 Congratulations and thank you for the purchase of your Rubbermaid 7' x 7' storage building. Before you begin assembly please be sure to check your local building codes, ordinances and restrictions, and applicable neighborhood governances. BEFORE YOU BEGIN – SURFACE PREPARATION To ensure proper assembly and performance your shed needs to be built on a solid, level surface.
  • Page 2 5H80 Description Assembly Letter Quantity Required Tools Front Floor Safety Back Floor Glasses Side Panel "A" Side Panel "B" Gloves Left Back Panel Right Back Panel Left Front Panel 94¼" Right Front Panel Wall Connector Utility Knife Left Door Panel...
  • Page 3 FLOOR PLAN: Build a solid, level surface for the shed foundation; minimum foundation dimensions are shown. Consult your local building authority for ordinances or restrictions before building Size the construction site to fit the entire floor. any structure at your home. OPTIONAL STEP: Note: If desired, recessed anchor locations (8 places) can be used to anchor the shed floor to a...
  • Page 4 Using a screwdriver, punch out the screw holes on the top of Left Front Panel (E) Using a screwdriver, punch out the screw holes on the top of Side Panel (B) 3 places. 3 places. Lubricate dovetails on Side Panel (A) 5 places with liquid soap. Connect Align the lap joint between Side Panel (A) and Side Panel (B).
  • Page 5 Using a screwdriver, punch out the screw holes on the top of Side Panel (B) 3 places. Using a screwdriver, punch out the screw holes on the top of Right Front Panel (F) Snap Side Panel (B) into Front Floor (J). Hold Side Panel (B) to prevent it from falling. 3 places.
  • Page 6 Lubricate dovetails on Side Panel (A) 5 places with liquid soap. Connect Right Back Install Wall Connector (Q) 5 places. Panel (D) onto dovetails of Side Panel (A). Align the lap joint between Left Back Panel (C) and Right Back Panel (D). Snap Right Back Panel (D) into Back Floor (K). click click click...
  • Page 7 Lubricate the inside of the Door Reinforcement (DR) along the full length with liquid soap. Install the Gasket (MM) into the gasket groove in the door. Start at the top and middle Starting at the top of the door, slide the Door Reinforcement (DR) onto the groove located by pushing the gasket into the groove.
  • Page 8 One person MUST hold onto the Front Gable (U) during this entire step. Set the Front Gable (U) onto the front wall panels. Install Left Door Panel (G) by inserting the lower hinge pin into the hole in Front Floor (J). Lift the left end of the Front Gable (U) enough to insert the top hinge pin on Left Door Panel (G) into the Front Gable (U) channel.
  • Page 9 Using a screwdriver, punch out the screw holes around the 2 skylight openings on Upper Fasten Upper Roof Panel (N) to Upper Roof Panel (P) using Screw (AA) 10 places. Roof Panel (P) 16 places. Fasten Skylight (L) 2 places to Upper Roof Panel (P), install Screws (AA) 16 places.
  • Page 10 Install the Truss assembly. Fasten Truss Bracket (TB) 2 places to the wall panels using Lift the Upper Roof Panel assembly onto the peak. Install Roof Pin (FF) 2 places. Screw (AA) 4 places. If necessary, use the Roof Pin Assembly Tool (GG) to pull the roof down. Tighten Bolt (DD) and Nut (EE) 7 places on the Truss Assembly.
  • Page 11 Using a screwdriver, punch out the screw holes on the top of Lower Roof Panel (M) 10 Upper Roof Panel places. While one person pushes up on the bottom of the Upper Roof Panel, slide the Lower Roof Panel (M) over the Purlin (PL) and under the Upper Roof Panel. Install Roof Pin (FF) 2 places.
  • Page 12 While one person holds the seam of the Roof down, fasten the Lower Roof Panel (M) to While one person holds the bottom of the Roof down, fasten the Wall Panels to the Roof the Upper Roof Panel using Screw (AA) 10 places. Repeat step for opposite side. Panels using Screw (AA) 12 places.
  • Page 13 85½" 84" Printed in U.S.A. Imprimé aux États-Unis Impreso en los EEUU. © 2011 Rubbermaid Incorporated, D.R. © 2011 Rubbermaid Incorporated, D.R. © 2011 Rubbermaid Incorporated, Huntersville, NC U.S.A. 28078-1801 Huntersville, NC U.S.A. 28078-1801 Huntersville, NC U.S.A. 28078-1801 Customer Service Service à...

Table of Contents

Save PDF