Advertisement
Quick Links
INTERFACE USER MANUAL
The Teisco Interface is compatible with devices that run
on Mac, Windows, iOS or Android.
Compatible Devices
MacBook (up to macOS Catalina)
iPhone (up to iOS 13)
*Requires Lightning to USB Camera Adapter
iPad Pro (up to iOS 13)
Laptop/PC (up to Windows 10)
*Recommended driver: WDM
Disclaimer: Results may vary for some Android mobile
devices. Audio latency issues may persist with some
Android operating systems.
Important Note
Due to its overall design, the Teisco Interface's Output A
is wired in reverse-stereo which may affect the output
routing in your DAW.
Track I/Os for your DAW:
Input A on the Teisco Interface = Input 1 on your DAW
Output A on the Teisco Interface = Output 2 on your DAW
Input B on the Teisco Interface = Input 2 on your DAW
Output B on the Teisco Interface = Output 1 on your DAW
For ease of use, we recommend trying out the sample
DAW Input and Output settings shown below.
Tried & Tested DAW Compatibility
This list represents music creation
software that works with the Interface:
Cakewalk by BandLab
Cubase 10
GarageBand 10
Logic Pro X
Pro Tools 2018*
Reaper 5
*Instructions for Pro Tools
1. Open Audio and MIDI Devices
2. Create aggregate device
3. Rename device
4. The Teisco interface should now
appear in Pro Tools as a playback engine
If your DAW or device is not on this list, it
might still work with the Interface!
Contact us at support@teisco.com if
you face compatibility issues.
Advertisement
Summary of Contents for Teisco Interface
- Page 1 Track I/Os for your DAW: you face compatibility issues. Input A on the Teisco Interface = Input 1 on your DAW Output A on the Teisco Interface = Output 2 on your DAW Input B on the Teisco Interface = Input 2 on your DAW...
- Page 2 Teisco Interface on a Pedalboard (MONO) DAW requirements: If it’s your first time using a recording interface, this is the best place to start. Create 1 MONO track in DAW Add plugins to the track as desired Connect your pedals or your guitar directly to the Teisco Interface’s input and connect the...
- Page 3 Teisco You may also run other pedals before or after Interface) the Teisco Interface for the desired effect. You can also run a mono input into the Teisco Track 1: Input 1+2, Stereo Out (if you’re Interface and process output in stereo.
- Page 4 ASAP, or if you’re just looking to clock in some silent practice, go ahead and use Create 1 STEREO track in DAW the Interface as a simple recording interface. Add plugins to the track as desired Use Output B for your headphones. You’ll need a Use these settings in your DAW: headphone jack adapter.
- Page 5 (time-based ones like delays and reverbs) in your amp’s effects loop. Use these settings in your DAW: The Teisco Interface can single-handedly handle Track 1: Input 1, Output 2 both operations by running Channel A before Track 2: Input 2, Output 1 your amp, and Channel B in the effects loop.
- Page 6 Teisco Interface with Two Instruments DAW requirements: The Teisco Interface is able to run two instruments, each with separate plugins. Both tracks can be recorded at the same time. Create 2 MONO tracks in DAW Add plugins to each track as desired...
- Page 7 Teisco Interface Running Direct and to The Teisco Interface can also route two DAW requirements: different signals on stage. Create 2 MONO tracks in DAW Send Channel A to your guitar amp and Channel Add plugins to each track as desired B to the mixer/monitor.
- Page 8 Teisco Interface for Wet / Dry Setups Use the Teisco Interface to send your dry signal DAW requirements: to your guitar amp, and your time-based “wet” effects to another amp or directly to the front Create 2 MONO tracks in DAW of house.